A method of switch selection for an electric vehicle drive

The key to reducing cost of electric vehicles is integration. All too often systems such as the motor, motor controller, batteries and vehicle chassis/body are considered as separate problems. The truth is that a lot of trade-offs can be made between these systems, causing an overall improvement in many areas including total cost. Motor controller and battery cost have a relatively simple relationship; the less energy lost in the motor controller the less energy that has to be carried in the batteries, hence the lower the battery cost. A motor controller’s cost is primarily influenced by the cost of the switches. This paper will therefore present a method of assessing the optimal switch selection on the premise that the optimal switch is the one that produces the lowest system cost, where system cost is the cost of batteries + switches.

An isolated MOSFET gate driver

Traditional methods of isolated MOSFET/IGBT gate drive are presented, and their pros and cons assessed. The best options are chosen to meet our objective— a small, high speed, low cost, low power isolated gate drive module. Two small ferrite bead transformers are used for isolation, one transmits power at 2.5MHz, the other sends narrow set reset pulses. On the secondary these pulses drive a transistor totem pole to ensure high current drive, and the value is held by CMOS buffers with positive feedback. An alternative design for driving logic level devices uses only an HC buffer on the secondary. Double sided SMDconstruction (primary one side, secondary on the other) yields an upright module 40x18x5mm. Propagation delaywas 20ns, and rise/fall time 15ns with a 1nF load. The design places no limits on frequency of operation or duty cycle. Power supply requirementswere 5V@20mA for operation below 100kHz, dominated by magnetising current.

Control of infrastructure inspection aircraft vertical dynamics in the presence of thermal disturbances

The low-altitude aircraft inspection of powerlines, or other linear infrastructure networks, is emerging as an important application requiring specialised control technologies. Despite some recent advances in automated control related to this application, control of the underactuated aircraft vertical dynamics has not been completely achieved, especially in the presence of thermal disturbances. Rejection of thermal disturbances represents a key challenge to the control of inspection aircraft due to the underactuated nature of the dynamics and specified speed, altitude, and pitch constraints. This paper proposes a new vertical controller consisting of a backstepping elevator controller with feedforward-feedback throttle controller. The performance of our proposed approach is evaluated against two existing candidate controllers.

System level tests of transformer differential protection using an IEC 61850 process bus

The IEC 61850 family of standards for substation communication systems were released in the early 2000s, and include IEC 61850-8-1 and IEC 61850-9-2 that enable Ethernet to be used for process-level connections between transmission substation switchyards and control rooms. This paper presents an investigation of process bus protection performance, as the in-service behavior of multi-function process buses is largely unknown. An experimental approach was adopted that used a Real Time Digital Simulator and 'live' substation automation devices. The effect of sampling synchronization error and network traffic on transformer differential protection performance was assessed and compared to conventional hard-wired connections. Ethernet was used for all sampled value measurements, circuit breaker tripping, transformer tap-changer position reports and Precision Time Protocol synchronization of sampled value merging unit sampling. Test results showed that the protection relay under investigation operated correctly with process bus network traffic approaching 100% capacity. The protection system was not adversely affected by synchronizing errors significantly larger than the standards permit, suggesting these requirements may be overly conservative. This 'closed loop' approach, using substation automation hardware, validated the operation of protection relays under extreme conditions. Digital connections using a single shared Ethernet network outperformed conventional hard-wired solutions.

The primary school as a logic machine

This paper makes a case for thinking about the primary school as a logic machine (apparatus) as a way of thinking about processes of in-school stratification. Firstly we discuss related literature on in-school stratification in primary schools, particularly as it relates to literacy learning. Secondly we explain how school reform can be thought about in terms of the idea of the machine or apparatus. In which case the processes of in-school stratification can be mapped as more than simply concerns about school organisation (such as students grouping) but also involve a politics of truth, played out in each school, that constitutes school culture and what counts as ‘good’ pedagogy. Thirdly, the chapter will focus specifically on research conducted into primary schools in the Northern Suburbs of Adelaide, one of the most educationally disadvantaged regions in Australia, as a case study of the relationship between in-school stratification and the reproduction of inequality. We will draw from more than 20 years of ethnographic work in primary school in the northern suburbs of Adelaide and provide a snapshot of a recent attempt to improve literacy achievement in a few Northern Suburbs public primary schools (SILA project). The SILA project, through diagnostic reviews, has provided a significant analysis of the challenges facing policy and practice in such challenging school contexts that also maps onto existing (inter)national research. These diagnostic reviews said ‘hard things’ that required attention by SILA schools and these included: · an over reliance on whole class, low level, routine tasks and hence a lack of challenge and rigour in the learning tasks offered to students ; · a focus on the 'code breaking' function of language at the expense of richer conceptualisations of literacy that might guide teachers’ understanding of challenging pedagogies ; · the need for substantial shifts in the culture of schools, especially unsettling deficit views of students and their communities ; · a need to provide a more ‘consistent’ approach to teaching literacy across the school; · a need to focus School Improvement Plans in order to implement a clear focus on literacy learning; and, · a need to sustain professional learning to produce new knowledge and practice . The paper will conclude with suggestions for further research and possible reform projects into the primary school as a logic machine.

Purification of particles of subterranean clover red leaf virus using an industrial-grade cellulase

Particles of two isolates of subterranean clover red leaf virus were purified by a method in which infected plant tissue was digested with an industrial-grade cellulase, Celluclast® 2.0 L type X. The yields of virus particles using this enzyme were comparable with those obtained using either of two laboratory-grade cellulases, Cellulase type 1 (Sigma) and Driselase®. However, the specific infectivity or aphid transmissibility of the particles purified using Celluclast® was 10-100 times greater than those of preparations obtained using laboratory-grade cellulases or no enzyme. The main advantage of using Celluclast® is that at present in Australia its cost is only ca. 1% of laboratory-grade cellulases.

Testing second order cyclostationarity in the squared envelope spectrum of non-white vibration signals

Cyclostationary models for the diagnostic signals measured on faulty rotating machineries have proved to be successful in many laboratory tests and industrial applications. The squared envelope spectrum has been pointed out as the most efficient indicator for the assessment of second order cyclostationary symptoms of damages, which are typical, for instance, of rolling element bearing faults. In an attempt to foster the spread of rotating machinery diagnostics, the current trend in the field is to reach higher levels of automation of the condition monitoring systems. For this purpose, statistical tests for the presence of cyclostationarity have been proposed during the last years. The statistical thresholds proposed in the past for the identification of cyclostationary components have been obtained under the hypothesis of having a white noise signal when the component is healthy. This need, coupled with the non-white nature of the real signals implies the necessity of pre-whitening or filtering the signal in optimal narrow-bands, increasing the complexity of the algorithm and the risk of losing diagnostic information or introducing biases on the result. In this paper, the authors introduce an original analytical derivation of the statistical tests for cyclostationarity in the squared envelope spectrum, dropping the hypothesis of white noise from the beginning. The effect of first order and second order cyclostationary components on the distribution of the squared envelope spectrum will be quantified and the effectiveness of the newly proposed threshold verified, providing a sound theoretical basis and a practical starting point for efficient automated diagnostics of machine components such as rolling element bearings. The analytical results will be verified by means of numerical simulations and by using experimental vibration data of rolling element bearings.

Comparison of high level FPGA hardware design for solving tri-diagonal linear systems

Reconfigurable computing devices can increase the performance of compute intensive algorithms by implementing application specific co-processor architectures. The power cost for this performance gain is often an order of magnitude less than that of modern CPUs and GPUs. Exploiting the potential of reconfigurable devices such as Field-Programmable Gate Arrays (FPGAs) is typically a complex and tedious hardware engineering task. Re- cently the major FPGA vendors (Altera, and Xilinx) have released their own high-level design tools, which have great potential for rapid development of FPGA based custom accelerators. In this paper, we will evaluate Altera’s OpenCL Software Development Kit, and Xilinx’s Vivado High Level Sythesis tool. These tools will be compared for their per- formance, logic utilisation, and ease of development for the test case of a Tri-diagonal linear system solver.

Cross-layer design for traffic management in wireless networked control systems

Wireless networked control systems (WNCSs) have been increasingly deployed in industrial applications. As they require timely data packet transmissions, it is difficult to make efficient use of the limited channel resources, particularly in contention based wireless networks in the layered network architecture. Aiming to maintain the WNCSs under critical real-time traffic condition at which the WNCSs marginally meet the real-time requirements, a cross-layer design (CLD) approach is presented in this paper to adaptively adjust the control period to achieve improved channel utilization while still maintaining effective and timely packet transmissions. The effectiveness of the proposed approach is demonstrated through simulation studies.

Reluctantly virtual : modelling copyright industry dynamics

During the evolution of the music industry, developments in the media environment have required music firms to adapt in order to survive. Changes in broadcast radio programming during the 1950s; the Compact Cassette during the 1970s; and the deregulation of media ownership during the 1990s are all examples of changes which have heavily affected the music industry. This study explores similar contemporary dynamics, examines how decision makers in the music industry perceive and make sense of the developments, and reveals how they revise their business strategies, based on their mental models of the media environment. A qualitative system dynamics model is developed in order to support the reasoning brought forward by the study. The model is empirically grounded, but is also based on previous music industry research and a theoretical platform constituted by concepts from evolutionary economics and sociology of culture. The empirical data primarily consist of 36 personal interviews with decision makers in the American, British and Swedish music industrial ecosystems. The study argues that the model which is proposed, more effectively explains contemporary music industry dynamics than music industry models presented by previous research initiatives. Supported by the model, the study is able to show how “new” media outlets make old music business models obsolete and challenge the industry’s traditional power structures. It is no longer possible to expose music at one outlet (usually broadcast radio) in the hope that it will lead to sales of the same music at another (e.g. a compact disc). The study shows that many music industry decision makers still have not embraced the new logic, and have not yet challenged their traditional mental models of the media environment. Rather, they remain focused on preserving the pivotal role held by the CD and other physical distribution technologies. Further, the study shows that while many music firms remain attached to the old models, other firms, primarily music publishers, have accepted the transformation, and have reluctantly recognised the realities of a virtualised environment.

Supermarkets and agro-industrial foods : the strategic manufacturing of consumer trust

There is increasing evidence of a weakened platform of consumer trust in mass produced food products. The resistance shown by consumers to the agro-industrial paradigm is evident in an emergent phase of reflexive consumerism, public reactions to an overly-concentrated retail sector and the rise of alternative food networks such as farmers' markets and organic box schemes. Supermarkets are responding strategically by aiming to manufacture new trust relations with consumers. This paper identifies three key strategies of trust manufacturing: (i) reputational enhancement though the institution of “behind the scenes,” business-to-business private standards; (ii) direct quality claims via private standard certification badges on food products, and ; (iii) discursive claimsmaking through symbolic representations of “authenticity” and “tradition.” Drawing upon the food governance literature and a “visual sociology” of supermarkets and supermarket produce, we highlight how trust is both commoditized and increasingly embedded into the marketing of mass-produced foods.

Pulse-coupled neural network performance for real-time identification of vegetation during forced landing

Safety concerns in the operation of autonomous aerial systems require safe-landing protocols be followed during situations where the mission should be aborted due to mechanical or other failure. This article presents a pulse-coupled neural network (PCNN) to assist in the vegetation classification in a vision-based landing site detection system for an unmanned aircraft. We propose a heterogeneous computing architecture and an OpenCL implementation of a PCNN feature generator. Its performance is compared across OpenCL kernels designed for CPU, GPU, and FPGA platforms. This comparison examines the compute times required for network convergence under a variety of images to determine the plausibility for real-time feature detection.

Provotypes: Teasing out tensions between industrial context and use context

What industrial organisations think people do and what they actually do are often two very different things. But exactly this tension can be a source of innovation: how can we give form to insights about what people do, to deliberately challenge industries' conceptions, and inspire new product and service development

Ethnography of software maintenance activities in an industrial engineering setup

New technical and procedural interventions are less likely to be adopted in industry, unless they are smoothly integrated into the existing practices of professionals. In this paper, we provide a case study of the use of ethnographic methods for studying software bug-fixing activities at an industrial engineering conglomerate. We aimed at getting an in-depth understanding of software developers' everyday practices in bug-fixing related projects and in turn inform the design of novel productivity tools. The use of ethnography has allowed us to look at the social side of software maintenance practices. In this paper, we highlight: 1) organizational issues that influence bug-fixing activities; 2) social role of bug tracking systems, and; 3) social issues specific to different phases of bug-fixing activities.

Numerical investigation of mechanical and thermal dynamic properties of the industrial transformer

Industrial transformer is one of the most critical assets in the power and heavy industry. Failures of transformers can cause enormous losses. The poor joints of the electrical circuit on transformers can cause overheating and results in stress concentration on the structure which is the major cause of catastrophic failure. Few researches have been focused on the mechanical properties of industrial transformers under overheating thermal conditions. In this paper, both mechanical and thermal properties of industrial transformers are jointly investigated using Finite Element Analysis (FEA). Dynamic response analysis is conducted on a modified transformer FEA model, and the computational results are compared with experimental results from literature to validate this simulation model. Based on the FEA model, thermal stress is calculated under different temperature conditions. These analysis results can provide insights to the understanding of the failure of transformers due to overheating, therefore are significant to assess winding fault, especially to the manufacturing and maintenance of large transformers.