On-road ultrafine particle concentration in the M5 East road tunnel, Sydney, Australia

The human health effects following exposure to ultrafine (<100nm) particles (UFPs) produced by fuel combustion, while not completely understood, are generally regarded as detrimental. Road tunnels have emerged as locations where maximum exposure to these particles may occur for the vehicle occupants using them. This study aimed to quantify and investigate the determinants of UFP concentrations in the 4km twin-bore (eastbound and westbound) M5 East tunnel in Sydney, Australia. Sampling was undertaken using a condensation particle counter (CPC) mounted in a vehicle traversing both tunnel bores at various times of day from May through July, 2006. Supplementary measurements were conducted in February, 2008. Over three hundred transects of the tunnel were performed, and these were distributed evenly between the bores. Additional comparative measurements were conducted on a mixed route comprising major roads and shorter tunnels, all within Sydney. Individual trip average UFP concentrations in the M5 East tunnel bores ranged from 5.53 × 104 p cm-3 to 5.95 × 106 p cm-3. Data were sorted by hour of capture, and hourly median trip average (HMA) UFP concentrations ranged from 7.81 × 104 p cm-3 to 1.73 × 106 p cm-3. Hourly median UFP concentrations measured on the mixed route were between 3.71 × 104 p cm-3 and 1.55 × 105 p cm-3. Hourly heavy diesel vehicle (HDV) traffic volume was a very good determinant of UFP concentration in the eastbound tunnel bore (R2 = 0.87), but much less so in the westbound bore (R2 = 0.26). In both bores, the volume of passenger vehicles (i.e. unleaded gasoline-powered vehicles) was a significantly poorer determinant of particle concentration. When compared with similar studies reported previously, the measurements described here were among the highest recorded concentrations, which further highlights the contribution road tunnels may make to the overall UFP exposure of vehicle occupants.

Off-site Manufacture in Australia : Current State and Future Directions

Off-site manufacture (OSM) offers numerous benefits to all parties in the construction process. The uptake of OSM in Australia has, however, been limited. This limited uptake corresponds to similar trends in the UK and US, although the level of OSM there appears to be increasing. This project undertook three workshops — one each in Victoria, Queensland and Western Australia — and 18 interviews with key stakeholders to assist in identifying the general benefits and barriers to OSM uptake in the Australian construction industry. Seven case studies were also undertaken, involving construction projects that used OSM, ranging from civil projects through to residential. Each of these case studies has been analysed to identify what worked and what didn’t, and suggest the lessons to be learned from each project.

Drivers constraints and the future of off-site manufacture in Australia.

Much has been written on Off-site Manufacture (OSM) in construction, particularly regarding the perceived benefits and barriers to implementation. However, very little understanding of the state of OSM in the Australian construction industry exists. A ‘scoping study' has recently been undertaken to determine the ‘state-of-the-art’ of OSM in Australia. This involved several industry workshops, interviews and case studies across four major states of Australia. The study surveyed a range of suppliers across the construction supply-chain, incorporating the civil, commercial and housing segments of the market. This revealed that skills shortages and lack of adequate OSM knowledge are generally the greatest issues facing OSM in Australia. The drivers and constraints that emerged from the research were, in large measure, consistent with those found in the US and UK, although some Australian anomalies are evident, such as the geographical disparity of markets. A comparative analysis with similar studies in the UK and US is reported, illustrating both the drivers and constraints confronting the industry in Australia. OSM uptake into the future is however dependent on many factors, not least of which is a better understanding of the construction process and its associated costs.

The ethical predisposition of university students in Western Australia : 1997 vs 2007

A sample of 285 Western Australian university students was used to assess the prevailing attitudes regarding potential breaches of ethical conduct on the part of business practitioners and organisations. The authors developed an ethical profile for the 2007 sample based on 14 scenarios used in the questionnaire. This profile was then compared to the results from data collected in 1997 using similar sampling and the same survey instrument. The prevailing predisposition is best viewed as centrist in nature, with a move to a more ethical stance in the last 10 years.

The reliability of information on work-related injuries available from hospitalisation data in Australia

Objective: To examine the reliability of work-related activity coding for injury-related hospitalisations in Australia. Method: A random sample of 4373 injury-related hospital separations from 1 July 2002 to 30 June 2004 were obtained from a stratified random sample of 50 hospitals across 4 states in Australia. From this sample, cases were identified as work-related if they contained an ICD-10-AM work-related activity code (U73) allocated by either: (i) the original coder; (ii) an independent auditor, blinded to the original code; or (iii) a research assistant, blinded to both the original and auditor codes, who reviewed narrative text extracted from the medical record. The concordance of activity coding and number of cases identified as work-related using each method were compared. Results: Of the 4373 cases sampled, 318 cases were identified as being work-related using any of the three methods for identification. The original coder identified 217 and the auditor identified 266 work-related cases (68.2% and 83.6% of the total cases identified, respectively). Around 10% of cases were only identified through the text description review. The original coder and auditor agreed on the assignment of work-relatedness for 68.9% of cases. Conclusions and Implications: The current best estimates of the frequency of hospital admissions for occupational injury underestimate the burden by around 32%. This is a substantial underestimate that has major implications for public policy, and highlights the need for further work on improving the quality and completeness of routine, administrative data sources for a more complete identification of work-related injuries.

The reputation of the corporate social responsibility industry in Australia

Corporate social responsibility (CSR) is increasingly seen as an imperative for sustainable business and there is a growing literature on the effect of CSR on corporate reputation. Despite this, a pall of ambiguity and uncertainty remains around what CSR means and how it should be practiced. This paper offers a unique addition to the body of literature to date by revealing that CSR is an emerging industry in Australia, which is in the process of developing its own reputation as a set of business practices. The paper is based on exploratory qualitative research using a case study methodology. Interviews were conducted with key actors within the industry to investigate shared understandings of what CSR means, perceptions of CSR practice and of the industry as a whole, and who is involved in shaping these perceptions. The research revealed that the CSR industry in Australia is in its early stages of development and is therefore in need of increased internal cooperation if it is to develop a strong reputation.

The response to dryness in Australia

The drought Australia now faces is leading to shifts in the perception of the continent, of Australians and the world. The ideals of lush green landscapes are making way for landscape designs in which dryness is a quality of the design. On a map of the world, Australia is enormous, and seems empty because development is concentrated around its edges. Its heart must be red, in the cultural projections of the world from images of Uluru, 'the rock', set in a flat desert with no relief. Of course the country is not really all desert - surely? - with low shrubs pretty much throughout. Inhabitation seems to cling to the edges where teh continent feels microclimatic effects from the adjacent oceans and edging mountain ranges, which screen the population from the real state of the environment - dry, harsh, amazing and unique. Australia is rightly proud of this harsh difference from its edges, but prefers the harshness to be 'out there'. At the moment however, the country is pretty much universally in drought, and the contrast between green and brown, that it has celebrated, even built its identity around, is disappearing to become brown throughout. Without the browning of Australia, some areas, such as tropical Queensland, are having their designed public landscapes and gardens revealed as an elaborate mythology, a landscape fraud.

Open access policies, practices and licensing : a review of the literature in Australia and selected jurisdictions

The full economic, cultural and environmental value of information produced or funded by the public sector can be realised through enabling greater access to and reuse of the information. To do this effectively it is necessary to describe and implement a policy framework that supports greater access and reuse among a distributed, online network of information suppliers and users. The objective of this study was to identify materials dealing with policies, principles and practices relating to information access and reuse in Australia and in other key jurisdictions internationally. Open Access Policies, Practices and Licensing: A review of the literature in Australia and selected jurisdictions sets out the findings of an extensive review of published materials dealing with policies, practices and legal issues relating to information access and reuse, with a particular focus on materials generated, held or funded by public sector bodies. The report was produced as part of the work program of the project “Enabling Real-Time Information Access in Both Urban and Regional Areas”, established within the Cooperative Research Centre for Spatial Information (CRCSI).

Increasing socio-economic inequalities in drug-induced deaths in Australia : 1981-2002

Introduction and Aims: Since the 1990s illicit drug use death rates in Australia have increased markedly. There is a notable gap in knowledge about changing socio-economic inequalities in drug use death rates. Some limited Australian and overseas data point to higher rates of drug death in the lowest socio-economic groups, but the paucity of available studies and their sometimes conflicting findings need to be addressed. Design and Methods: This paper uses data obtained from the Australian Bureau of Statistics (ABS) to examine changes in age-standardised drug-induced mortality rates for Australian males over the period 1981 – 2002. Socio-economic status was categorised as manual or non-manual work status. Results: With the rapid increase in drug-induced mortality rates in the 1990s, there was a parallel increase in socio-economic inequalities in drug-induced deaths. The decline in drug death rates from 2000 onwards was associated with a decline in socio-economic inequalities. By 2002, manual workers had drug death rates well over twice the rate of non-manual workers. Discussion: Three factors are identified which contribute to these socio-economic inequalities in mortality. First, there has been an age shift in deaths evident only for manual workers. Secondly, there has been an increase in availability until 1999 and a relative decline in the cost of the drug, which most often leads to drug death (heroin). Thirdly, there has been a shift to amphetamine use which may lead to significant levels of morbidity, but few deaths. [Najman JM, Toloo G, Williams GM. Increasing socio-economic inequalities in drug-induced deaths in Australia: 1981–2002.

Growing demand for emergency health services in Queensland, Australia

Introduction: The demand for emergency health services (EHS), both in the prehospital (ambulance) and hospital (emergency departments) settings, is growing rapidly in Australia. Broader health system changes have reduced available health infrastructure, particularly hospital beds, resulting in reduced access to and congestion of the EHS as demonstrated by longer waiting times and ambulance “ramping”. Ambulance ramping occurring when patients have a prolonged wait on the emergency vehicle due to the unavailability of hospital beds. This presentation will outline the trends in EHS demand in Queensland compared with the rest of Australia and factors that appear to be contributing to the growth in demand. Methods: Secondary analysis was conducted using data from publicly available sources. Data from the Queensland Ambulance Service and Queensland Health Emergency Department Information System (EDIS) also were analyzed. Results: The demand for ambulance services and emergency departments has been increasing at 8% and 4% per year over the last decade, respectively; while accessible hospital beds have reduced by almost 10% contributing to the emergency department congestion and possibly contributing to the prehospital demand. While the increase in the proportion of the elderly population seems to explain a great deal of the demand for EHS, other factors also influence this growth including patient characteristics, institutional and societal factors, economic, EHS arrangements, and clinical factors. Conclusions: Overcrowding of facilities that provide EHS are causing considerable community concern. This overcrowding is caused by the growing demand and reduced access. The causes of this growing demand are complex, and require further detailed analysis in order to quantify and qualify these causes in order to provide a resilient foundation of evidence for future policy direction.

Continuation rates and reasons for removal among Implanon® users accessing two family planning clinics in Queensland, Australia

Background - This study examined demographic profile, continuation rates and reasons for removal among Implanon^® users accessing two family planning clinics in Queensland, Australia. Study Design - A retrospective chart audit of 976 women who attended for implant insertion over a 3-year period between May 2001 and May 2004. Results - Continuation rates showed that at 6 months after insertion, 94% of women continued, 74% continued at 1 year and 50% continued at 2 years. Metropolitan women were more likely than rural women to discontinue use because of dissatisfaction with bleeding patterns. Cox regression analysis showed that those attending the regional clinic experienced significantly shorter time to removal. Conclusions - Implanon® continuation rates and reasons for removal differ between clinics in metropolitan and rural locations. A cooling-off period did not affect the likelihood of continuation with Implanon®. Preinsertion counselling should emphasize potential changes in bleeding patterns.

Knowing a donor and identifying as one : determinants of people's willingness for related and anonymous living donation in Australia

While LRD (living donation to a genetically/emotionally related recipient) is well established in Australia, LAD (living anonymous donation to a stranger) is rare. Given the increasing use of LAD overseas, Australia may likely follow suit. Understanding the determinants of people’s willingness for LAD is essential but infrequently studied in Australia. Consequently, we compared the determinants of people’s LRD and LAD willingness, and assessed whether these determinants differed according to type of living donation. We surveyed 487 health students about their LRD and LAD willingness, attitudes, identity, prior experience with blood and organ donation, deceased donation preference, and demographics. We used Structural Equation Modelling (SEM) to identify the determinants of willingness for LRD and LAD and paired sample t-tests to examine differences in LRD and LAD attitudes, identity, and willingness. Mean differences in willingness (LRD 5.93, LAD 3.92), attitudes (LRD 6.43, LAD 5.53), and identity (LRD 5.69, LAD 3.58) were statistically significant. Revised SEM models provided a good fit to the data (LRD: x2 (41) = 67.67, p = 0.005, CFI = 0.96, RMSEA = 0.04; LAD: x2 (40) = 79.64, p < 0.001, CFI = 0.95, RMSEA = 0.05) and explained 45% and 54% of the variation in LRD and LAD willingness, respectively. Four common determinants of LRD and LAD willingness emerged: identity, attitude, past blood donation, and knowing a deceased donor. Religious affiliation and deceased donation preference predicted LAD willingness also. Identifying similarities and differences in these determinants can inform future efforts aimed at understanding people’s LRD and LAD willingness and the evaluation of potential living donor motives. Notably, this study highlights the importance of people’s identification as a living donor as a motive underlying their willingness to donate their organs while living.

A comparison of farmland returns in Australia, Canada, New Zealand and United States

Rural land is still a major property asset class and rural commodity production is an important domestic and export market in all economies. This paper carries out a comprehensive analysis of both rural production and land prices in four major rural production countries. The study compares rural property values in Unites States, Canada, Australia and New Zealand over a period 1990 to 2005 and analyzes and compares the capital return and total return performance for rural land in these four countries. The analysis allows a comparison of farm land returns for both a subsidised and non-subsidised farming policy to determine if levels of farm support result in variations in farm profitability and therefore farm land values.

Amniotic fluid stem cells produce robust mineral deposits on biodegradable scaffolds

Insufficient availability of osteogenic cells limits bone regeneration through cell-based therapies. This study investigated the potential of amniotic fluid–derived stem (AFS) cells to synthesize mineralized extracellular matrix within porous medical-grade poly-e-caprolactone (mPCL) scaffolds. The AFS cells were initially differentiated in two-dimensional (2D) culture to determine appropriate osteogenic culture conditions and verify physiologic mineral production by the AFS cells. The AFS cells were then cultured on 3D mPCL scaffolds (6-mm diameter9-mm height) and analyzed for their ability to differentiate to osteoblastic cells in this environment. The amount and distribution of mineralized matrix production was quantified throughout the mPCL scaffold using nondestructive micro computed tomography (microCT) analysis and confirmed through biochemical assays. Sterile microCT scanning provided longitudinal analysis of long-term cultured mPCL constructs to determine the rate and distribution of mineral matrix within the scaffolds. The AFS cells deposited mineralized matrix throughout the mPCL scaffolds and remained viable after 15 weeks of 3D culture. The effect of predifferentiation of the AFS cells on the subsequent bone formation in vivo was determined in a rat subcutaneous model. Cells that were pre-differentiated for 28 days in vitro produced seven times more mineralized matrix when implanted subcutaneously in vivo. This study demonstrated the potential of AFS cells to produce 3D mineralized bioengineered constructs in vitro and in vivo and suggests that AFS cells may be an effective cell source for functional repair of large bone defects