Hip joint stabilization vs. propulsion and resistance in individuals with transfemoral amputation

Joint moments and joint powers are widely used to determine the effects of rehabilitation programs and prosthetic components (e.g., alignments). A complementary analysis of the 3D angle between joint moment and joint angular velocity has been proposed to assess whether the joints are predominantly driven or stabilized.

Dynamic input to determine hip joint moments, power and work on the prosthetic limb of transfemoral amputees: ground reactions vs knee reactions

Study Design: Comparative analysis Background: Calculations of lower limbs kinetics are limited by floor-mounted force-plates. Objectives: Comparison of hip joint moments, power and mechanical work on the prosthetic limb of a transfemoral amputee calculated by inverse dynamics using either the ground reactions (force-plates) or knee reactions (transducer). Methods: Kinematics, ground reactions and knee reactions were collected using a motion analysis system, two force-plates and a multi-axial transducer mounted below the socket, respectively. Results: The inverse dynamics using ground reactions under-estimated the peaks of hip energy generation and absorption occurring at 63 % and 76 % of the gait cycle (GC) by 28 % and 54 %, respectively. This method over-estimated a phase of negative work at the hip (from 37 %GC to 56 %GC) by 24%. It under-estimated the phases of positive (from 57 %GC to 72 %GC) and negative (from 73 %GC to 98 %GC) work at the hip by 11 % and 58%, respectively. Conclusions: A transducer mounted within the prosthesis has the capacity to provide more realistic kinetics of the prosthetic limb because it enables assessment of multiple consecutive steps and a wide range of activities without issues of foot placement on force-plates. CLINICAL RELEVANCE The hip is the only joint that an amputee controls directly to set in motion the prosthesis. Hip joint kinetics are associated with joint degeneration, low back pain, risks of fall, etc. Therefore, realistic assessment of hip kinetics over multiple gait cycles and a wide range of activities is essential.

Inferring lung cancer risk factor patterns through joint Bayesian spatio-temporal analysis

Background: Preventing risk factor exposure is vital to reduce the high burden from lung cancer. The leading risk factor for developing lung cancer is tobacco smoking. In Australia, despite apparent success in reducing smoking prevalence, there is limited information on small area patterns and small area temporal trends. We sought to estimate spatio-temporal patterns for lung cancer risk factors using routinely collected population-based cancer data. Methods: The analysis used a Bayesian shared component spatio-temporal model, with male and female lung cancer included separately. The shared component reflected exposure to lung cancer risk factors, and was modelled over 477 statistical local areas (SLAs) and 15 years in Queensland, Australia. Analyses were also run adjusting for area-level socioeconomic disadvantage, Indigenous population composition, or remoteness. Results: Strong spatial patterns were observed in the underlying risk factor exposure for both males (median Relative Risk (RR) across SLAs compared to the Queensland average ranged from 0.48-2.00) and females (median RR range across SLAs 0.53-1.80), with high exposure observed in many remote areas. Strong temporal trends were also observed. Males showed a decrease in the underlying risk across time, while females showed an increase followed by a decrease in the final two years. These patterns were largely consistent across each SLA. The high underlying risk estimates observed among disadvantaged, remote and indigenous areas decreased after adjustment, particularly among females. Conclusion: The modelled underlying exposure appeared to reflect previous smoking prevalence, with a lag period of around 30 years, consistent with the time taken to develop lung cancer. The consistent temporal trends in lung cancer risk factors across small areas support the hypothesis that past interventions have been equally effective across the state. However, this also means that spatial inequalities have remained unaddressed, highlighting the potential for future interventions, particularly among remote areas.

Changes in cervical spine bone mineral density in response to flight training

BACKGROUND High magnitude loads and unusual loading regimes are two important determinants for increasing bone mass. Past research demonstrated that positive Gz-induced loading, providing high loads in an unaccustomed manner, had an osteogenic effect on bone. Another determinant of bone mass is that the bone response to loading is site specific. This study sought to further investigate the site specific bone response to loading, examining the cervical spine response, the site suspected of experiencing the greatest loading, to high performance flight. METHODS Bone mineral density (BMD) and bone mineral content (BMC) was monitored in 9 RAAF trainee fighter pilots completing an 8-mo flight training course on a PC-9 and 10 age-height-weight-matched controls. RESULTS At completion of the course, the pilots had a significant increase in cervical spine BMD and total body BMC. No significant changes were found for the control group. CONCLUSIONS This study demonstrated that the physical environment associated with flight training may have contributed to a significant increase in cervical spine bone mass in the trainee PC-9 pilots. The increase in bone mass was possibly a response to the strain generated by the daily wearing of helmet and mask assembly under the influence of positive sustained accelerative forces.

MRI reveals individual level deformities in the growing scoliotic spine that clinically are masked by the Cobb angle

Clinically, the Cobb angle method measures the overall scoliotic curve in the coronal plane but does not measure individual vertebra and disc wedging. The contributions of the vertebrae and discs in the growing scoliotic spine were measured using sequential MRI scans to investigate coronal plane deformity progression with growth. Sequential MRI data showed complex patterns of deformity progression. Changes to the wedging of individual vertebrae and discs may occur in patients who have no increase in overall Cobb angle measure; the Cobb method alone may be insufficient to capture the complex mechanisms of deformity progression.

Cross-cultural adaptation, reliability and validity of the Turkish version of the spine functional index

Background The Spine Functional Index (SFI) is a patient reported outcome measure with sound clinimetric properties and clinical viability for the determination of whole-spine impairment. To date, no validated Turkish version is available. The purpose of this study is to cross-culturally adapted the SFI for Turkish-speaking patients (SFI-Tk) and determine the psychometric properties of reliability, validity and factor structure in a Turkish population with spine musculoskeletal disorders. Methods The SFI English version was culturally adapted and translated into Turkish using a double forward and backward method according to established guidelines. Patients (n = 285, cervical = l29, lumbar = 151, cervical and lumbar region = 5, 73% female, age 45 ± 1) with spine musculoskeletal disorders completed the SFI-Tk at baseline and after a seven day period for test-retest reliability. For criterion validity the Turkish version of the Functional Rating Index (FRI) was used plus the Neck Disability Index (NDI) for cervical patients and the Oswestry Disability Index (ODI) for back patients. Additional psychometric properties were determined for internal consistency (Chronbach’s α), criterion validity and factor structure. Results There was a high degree of internal consistency (α = 0.85, item range 0.80-0.88) and test-retest reliability (r = 0.93, item range = 0.75-0.95). The factor analysis demonstrated a one-factor solution explaining 24.2% of total variance. Criterion validity with the ODI was high (r = 0.71, p < 0.001) while the FRI and NDI were fair (r = 0.52 and r = 0.58, respectively). The SFI-Tk showed no missing responses with the ‘half-mark’ option used in 11.75% of total responses by 77.9% of participants. Measurement error from SEM and MDC90 were respectively 2.96% and 7.12%. Conclusions The SFI-Tk demonstrated a one-factor solution and is a reliable and valid instrument. The SFI-Tk consists of simple and easily understood wording and may be used to assess spine region musculoskeletal disorders in Turkish speaking patients.

ACE research briefing paper 008 : How to Design and Manage Successful Joint Ventures in the Exploration Space

Joint ventures are formed and dissolved regularly in the mining industry. What impact do such changes have on the viability of mineral exploration projects? The Australian Centre for Entrepreneurship Research (ACE) has taken 9 years' worth of data (2002-2011) on 1,025 joint ventures in the Australasian mining industry and studied trends in fomentation, dissolution, and reconfiguration and how they impact project outcomes. This research is generously sponsored by the Queensland Exploration Council (QEC) and the Australian Research Council (ARC).

Medical imaging and Biomechanical analysis of scoliosis progression in the growing adolescent spine

Progression of spinal deformity in children was studied with Computed Tomography (CT) and Magnetic Resonance Imaging (MRI) to identify how gravity affects the deformity and to determine the full three-dimensional character of the deformity. The CT study showed that gravity is significant in deformity progression in some patients which has implications for clinical patient management. The world first MRI study showed that the standard clinical measure used to define the extent of the deformity is inadequate and further use of three-dimensional MRI should be considered by spinal surgeons.

Treatment of proximal interphalangeal joint flexion contracture: Combined static and dynamic orthotic intervention compared with other therapy intervention: randomized controlled trial

Purpose To test the effectiveness of static and dynamic orthoses using them as an exclusive treatment for proximal interphalangeal (PIP) joint flexion contracture compared with other hand therapy conservative treatments described in the literature. Methods 60 patients who used orthoses were compared with a control group that received other hand therapy treatments. Clinical assessments were measured before the experiment and 3 months after and included active PIP joint extension and function. Results A significant improvement in the extension active range of motion at the PIP joint in the second measurement was found in both groups, but it was significantly greater in the experimental group. Improvement in function (Disabilities of the Arm, Shoulder, and Hand score) between the first and second assessment was similar in the control and experimental groups. Conclusions Using night progressive static and daily dynamic orthoses as an exclusive treatment during the proliferative phase led to significant improvements in the PIP joint active extension, but the improvement did not correlate with increased function as perceived by the patient.

Development of a new ultrasound-based system for tracking motion of the human lumbar spine: Reliability, stability and repeatability during forward bending movement trials

The aim of this study was to develop a new method for quantifying intersegmental motion of the spine in an instrumented motion segment L4–L5 model using ultrasound image post-processing combined with an electromagnetic device. A prospective test–retest design was employed, combined with an evaluation of stability and within- and between-day intra-tester reliability during forward bending by 15 healthy male patients. The accuracy of the measurement system using the model was calculated to be ± 0.9° (standard deviation = 0.43) over a 40° range and ± 0.4 cm (standard deviation = 0.28) over 1.5 cm. The mean composite range of forward bending was 15.5 ± 2.04° during a single trial (standard error of the mean = 0.54, coefficient of variation = 4.18). Reliability (intra-class correlation coefficient = 2.1) was found to be excellent for both within-day measures (0.995–0.999) and between-day measures (0.996–0.999). Further work is necessary to explore the use of this approach in the evaluation of biomechanics, clinical assessments and interventions.

Spine curvature analysis between participants with obesity and normal weight participants: A biplanar electromagnetic device measurement

To analyse and compare standing thoracolumbar curves in normal weight participants and participants with obesity, using an electromagnetic device, and to analyse the measurement reliability. Material and Methods. Cross-sectional study was carried out. 36 individuals were divided into two groups (normal-weight and participants with obesity) according to their waist circumference. The reference points (T1–T8–L1–L5 and both posterior superior iliac spines) were used to perform a description of thoracolumbar curvature in the sagittal and coronal planes. A transformation from the global coordinate system was performed and thoracolumbar curves were adjusted by fifth-order polynomial equations. The tangents of the first and fifth lumbar vertebrae and the first thoracic vertebra were determined from their derivatives. The reliability of the measurement was assessed according to the internal consistency of the measure and the thoracolumbar curvature angles were compared between groups. Results. Cronbach’s alpha values ranged between 0.824 (95% CI: 0.776–0.847) and 0.918 (95% CI: 0.903–0.949). In the coronal plane, no significant differences were found between groups; however, in sagittal plane, significant differences were observed for thoracic kyphosis. Conclusion. There were significant differences in thoracic kyphosis in the sagittal plane between two groups of young adults grouped according to their waist circumference.

The Australia-Chile free trade agreement 2008: Intellectual property and development. A submission to the Joint Standing Committee on treaties

A submission to the Joint Standing Committee on treaties

A Submission to the Joint Standing Committee on Treaties on the Anti-Counterfeiting Trade Agreement 2011 (# ACTA)

“If Hollywood could order intellectual property laws for Christmas, what would they look like? This is pretty close.” David Fewer “While European and American IP maximalists have pushed for TRIPS-Plus provisions in FTAs and bilateral agreements, they are now pushing for TRIPS-Plus-Plus protections in these various forums.” Susan Sell “ACTA is a threat to the future of a free and open Internet.” Alexander Furnas “Implementing the agreement could open a Pandora's box of potential human rights violations.” Amnesty International. “I will not take part in this masquerade.” Kader Arif, Rapporteur for the Anti-Counterfeiting Trade Agreement 2011 in the European Parliament Executive Summary As an independent scholar and expert in intellectual property, I am of the view that the Australian Parliament should reject the adoption of the Anti-Counterfeiting Trade Agreement 2011. I would take issue with the Department of Foreign Affairs and Trade’s rather partisan account of the negotiations, the consultations, and the outcomes associated with the Anti-Counterfeiting Trade Agreement 2011. In my view, the negotiations were secretive and biased; the local consultations were sometimes farcical because of the lack of information about the draft texts of the agreement; and the final text of the Anti-Counterfeiting Trade Agreement 2011 is not in the best interests of Australia, particularly given that it is a net importer of copyright works and trade mark goods and services. I would also express grave reservations about the quality of the rather pitiful National Interest Analysis – and the lack of any regulatory impact statement – associated with the Anti-Counterfeiting Trade Agreement 2011. The assertion that the Anti-Counterfeiting Trade Agreement 2011 does not require legislative measures is questionable – especially given the United States Trade Representative has called the agreement ‘the highest-standard plurilateral agreement ever achieved concerning the enforcement of intellectual property rights.’ It is worthwhile reiterating that there has been much criticism of the secretive and partisan nature of the negotiations surrounding the Anti-Counterfeiting Trade Agreement 2011. Sean Flynn summarizes these concerns: "The negotiation process for ACTA has been a case study in establishing the conditions for effective industry capture of a lawmaking process. Instead of using the relatively transparent and inclusive multilateral processes, ACTA was launched through a closed and secretive “‘club approach’ in which like-minded jurisdictions define enforcement ‘membership’ rules and then invite other countries to join, presumably via other trade agreements.” The most influential developing countries, including Brazil, India, China and Russia, were excluded. Likewise, a series of manoeuvres ensured that public knowledge about the specifics of the agreement and opportunities for input into the process were severely limited. Negotiations were held with mere hours notice to the public as to when and where they would be convened, often in countries half away around the world from where public interest groups are housed. Once there, all negotiation processes were closed to the public. Draft texts were not released before or after most negotiating rounds, and meetings with stakeholders took place only behind closed doors and off the record. A public release of draft text, in April 2010, was followed by no public or on-the-record meetings with negotiators." Moreover, it is disturbing that the Anti-Counterfeiting Trade Agreement 2011 has been driven by ideology and faith, rather than by any evidence-based policy making Professor Duncan Matthews has raised significant questions about the quality of empirical evidence used to support the proposal of Anti-Counterfeiting Trade Agreement 2011: ‘There are concerns that statements about levels of counterfeiting and piracy are based either on customs seizures, with the actual quantities of infringing goods in free circulation in any particular market largely unknown, or on estimated losses derived from industry surveys.’ It is particularly disturbing that, in spite of past criticism, the Department of Foreign Affairs and Trade has supported the Anti-Counterfeiting Trade Agreement 2011, without engaging the Productivity Commission or the Treasury to do a proper economic analysis of the proposed treaty. Kader Arif, Rapporteur for the Anti-Counterfeiting Trade Agreement 2011 in the European Parliament, quit his position, and said of the process: "I want to denounce in the strongest possible manner the entire process that led to the signature of this agreement: no inclusion of civil society organisations, a lack of transparency from the start of the negotiations, repeated postponing of the signature of the text without an explanation being ever given, exclusion of the EU Parliament's demands that were expressed on several occasions in our assembly. As rapporteur of this text, I have faced never-before-seen manoeuvres from the right wing of this Parliament to impose a rushed calendar before public opinion could be alerted, thus depriving the Parliament of its right to expression and of the tools at its disposal to convey citizens' legitimate demands.” Everyone knows the ACTA agreement is problematic, whether it is its impact on civil liberties, the way it makes Internet access providers liable, its consequences on generic drugs manufacturing, or how little protection it gives to our geographical indications. This agreement might have major consequences on citizens' lives, and still, everything is being done to prevent the European Parliament from having its say in this matter. That is why today, as I release this report for which I was in charge, I want to send a strong signal and alert the public opinion about this unacceptable situation. I will not take part in this masquerade." There have been parallel concerns about the process and substance of the Anti-Counterfeiting Trade Agreement 2011 in the context of Australia. I have a number of concerns about the substance of the Anti-Counterfeiting Trade Agreement 2011. First, I am concerned that the Anti-Counterfeiting Trade Agreement 2011 fails to provide appropriate safeguards in respect of human rights, consumer protection, competition, and privacy laws. It is recommended that the new Joint Parliamentary Committee on Human Rights investigate this treaty. Second, I argue that there is a lack of balance to the copyright measures in the Anti-Counterfeiting Trade Agreement 2011 – the definition of piracy is overbroad; the suite of civil remedies, criminal offences, and border measures is excessive; and there is a lack of suitable protection for copyright exceptions, limitations, and remedies. Third, I discuss trade mark law, intermediary liability, and counterfeiting. I express my concerns, in this context, that the Anti-Counterfeiting Trade Agreement 2011 could have an adverse impact upon consumer interests, competition policy, and innovation in the digital economy. I also note, with concern, the lobbying by tobacco industries for the Anti-Counterfeiting Trade Agreement 2011 – and the lack of any recognition in the treaty for the capacity of countries to take measures of tobacco control under the World Health Organization Framework Convention on Tobacco Control. Fourth, I note that the Anti-Counterfeiting Trade Agreement 2011 provides no positive obligations to promote access to essential medicines. It is particularly lamentable that Australia and the United States of America have failed to implement the Doha Declaration on the TRIPS Agreement and Public Health 2001 and the WTO General Council Decision 2003. Fifth, I express concerns about the border measures in the Anti-Counterfeiting Trade Agreement 2011. Such measures lack balance – and unduly favour the interests of intellectual property owners over consumers, importers, and exporters. Moreover, such measures will be costly, as they involve shifting the burden of intellectual property enforcement to customs and border authorities. Interdicting, seizing, and destroying goods may also raise significant trade issues. Finally, I express concern that the Anti-Counterfeiting Trade Agreement 2011 undermines the role of existing international organisations, such as the United Nations, the World Intellectual Property Organization and the World Trade Organization, and subverts international initiatives such as the WIPO Development Agenda 2007. I also question the raison d'être, independence, transparency, and accountability of the proposed new ‘ACTA Committee’. In this context, I am concerned by the shift in the position of the Labor Party in its approach to international treaty-making in relation to intellectual property. The Australian Parliament adopted the Australia-United States Free Trade Agreement 2004, which included a large Chapter on intellectual property. The treaty was a ‘TRIPs-Plus’ agreement, because the obligations were much more extensive and prescriptive than those required under the multilateral framework established by the TRIPS Agreement 1994. During the debate over the Australia-United States Free Trade Agreement 2004, the Labor Party expressed the view that it would seek to mitigate the effects of the TRIPS-Plus Agreement, when at such time it gained power. Far from seeking to ameliorate the effects of the Australia-United States Free Trade Agreement 2004, the Labor Government would seek to lock Australia into a TRIPS-Double Plus Agreement – the Anti-Counterfeiting Trade Agreement 2011. There has not been a clear political explanation for this change in approach to international intellectual property. For both reasons of process and substance, I conclude that the Australian Parliament and the Australian Government should reject the Anti-Counterfeiting Trade Agreement 2011. The Australian Government would do better to endorse the Washington Declaration on Intellectual Property and the Public Interest 2011, and implement its outstanding obligations in respect of access to knowledge, access to essential medicines, and the WIPO Development Agenda 2007. The case study of the Anti-Counterfeiting Trade Agreement 2011 highlights the need for further reforms to the process by which Australia engages in international treaty-making.

A Submission to the Joint Standing Committee on Treaties on the Korea-Australia Free Trade Agreement (KAFTA)

Australia and South Korea have signed a new free trade agreement - the Korea-Australia Free Trade Agreement (KAFTA). Is it a fair trade fairytale? Or is it a dirty deal done dirt cheap? Or somewhere in between? It is hard to tell, given the initial secrecy of the negotiations, and the complexity of the texts of the agreement There has been much debate in Parliament over the transparency of the trade agreement; the scope of market access provided under the deal; the impact of the investment chapter, with its investor-state dispute settlement clause; the intellectual property chapter; the environment chapter; its impact upon public health; and the labor rights chapter. KAFTA provides an indication of the approach of the new Conservative Government in Australia to other trade deals – such as the Trans-Pacific Partnership.