Designing ePortfolios for music postgraduate study : a practice-led inquiry

In this research I have examined how ePortfolios can be designed for Music postgraduate study through a practice led research enquiry. This process involved designing two Web 2.0 ePortfolio systems for a group of five post graduate music research students. The design process revolved around the application of an iterative methodology called Software Develop as Research (SoDaR) that seeks to simultaneously develop design and pedagogy. The approach to designing these ePortfolio systems applied four theoretical protocols to examine the use of digitised artefacts in ePortfolio systems to enable a dynamic and inclusive dialogue around representations of the students work. The research and design process involved an analysis of existing software and literature with a focus upon identifying the affordances of available Web 2.0 software and the applications of these ideas within 21st Century life. The five post graduate music students each posed different needs in relation to the management of digitised artefacts and the communication of their work amongst peers, supervisors and public display. An ePortfolio was developed for each of them that was flexible enough to address their needs within the university setting. However in this first SoDaR iteration data gathering phase I identified aspects of the university context that presented a negative case that impacted upon the design and usage of the ePortfolios and prevented uptake. Whilst the portfolio itself functioned effectively, the university policies and technical requirements prevented serious use. The negative case analysis of the case study found revealed that Access and Control and Implementation, Technical and Policy Constraints protocols where limiting user uptake. From the semistructured interviews carried out as part of this study participant feedback revealed that whilst the participants did not use the ePortfolio system I designed, each student was employing Web 2.0 social networking and storage processes in their lives and research. In the subsequent iterations I then designed a more ‘ideal’ system that could be applied outside of the University context that draws upon the employment of these resources. In conclusion I suggest recommendations about ePortfolio design that considers what the applications of the theoretical protocols reveal about creative arts settings. The transferability of these recommendations are of course dependent upon the reapplication of the theoretical protocols in a new context. To address the mobility of ePortfolio design between Institutions and wider settings I have also designed a prototype for a business card sized USB portal for the artists’ ePortfolio. This research project is not a static one; it stands as an evolving design for a Web 2.0 ePortfolio that seeks to refer to users needs, institutional and professional contexts and the development of software that can be incorporated within the design. What it potentially provides to creative artist is an opportunity to have a dialogue about art with artefacts of the artist products and processes in that discussion.

Advanced analysis of steel frame structures comprising non-compact sections

During the past decade, a significant amount of research has been conducted internationally with the aim of developing, implementing, and verifying "advanced analysis" methods suitable for non-linear analysis and design of steel frame structures. Application of these methods permits comprehensive assessment of the actual failure modes and ultimate strengths of structural systems in practical design situations, without resort to simplified elastic methods of analysis and semi-empirical specification equations. Advanced analysis has the potential to extend the creativity of structural engineers and simplify the design process, while ensuring greater economy and more uniform safety with respect to the ultimate limit state. The application of advanced analysis methods has previously been restricted to steel frames comprising only members with compact cross-sections that are not subject to the effects of local buckling. This precluded the use of advanced analysis from the design of steel frames comprising a significant proportion of the most commonly used Australian sections, which are non-compact and subject to the effects of local buckling. This thesis contains a detailed description of research conducted over the past three years in an attempt to extend the scope of advanced analysis by developing methods that include the effects of local buckling in a non-linear analysis formulation, suitable for practical design of steel frames comprising non-compact sections. Two alternative concentrated plasticity formulations are presented in this thesis: the refined plastic hinge method and the pseudo plastic zone method. Both methods implicitly account for the effects of gradual cross-sectional yielding, longitudinal spread of plasticity, initial geometric imperfections, residual stresses, and local buckling. The accuracy and precision of the methods for the analysis of steel frames comprising non-compact sections has been established by comparison with a comprehensive range of analytical benchmark frame solutions. Both the refined plastic hinge and pseudo plastic zone methods are more accurate and precise than the conventional individual member design methods based on elastic analysis and specification equations. For example, the pseudo plastic zone method predicts the ultimate strength of the analytical benchmark frames with an average conservative error of less than one percent, and has an acceptable maximum unconservati_ve error of less than five percent. The pseudo plastic zone model can allow the design capacity to be increased by up to 30 percent for simple frames, mainly due to the consideration of inelastic redistribution. The benefits may be even more significant for complex frames with significant redundancy, which provides greater scope for inelastic redistribution. The analytical benchmark frame solutions were obtained using a distributed plasticity shell finite element model. A detailed description of this model and the results of all the 120 benchmark analyses are provided. The model explicitly accounts for the effects of gradual cross-sectional yielding, longitudinal spread of plasticity, initial geometric imperfections, residual stresses, and local buckling. Its accuracy was verified by comparison with a variety of analytical solutions and the results of three large-scale experimental tests of steel frames comprising non-compact sections. A description of the experimental method and test results is also provided.

Transitions

Transitions represents a selection of works presented by 3rd year QUT design students undertaken as part of their coursework entitled "Environments in Transitions". The work focuses upon the migration of ideas and aesthetics from East to West, with particular consideration for the influence of Japanese woodblock prints, Wabi-Sabi themes and decorative motifs upon European design during the turn of the 19th century. The works exhibited included design artifacts of various themes, and associated print work which informed the design process. A small exhibition publication accompanied the exhibition and talk.

Green roofs : understanding their benefits for Australia

Summary of Actions Towards Sustainable Outcomes Environmental Issues / Principal Impacts The increased growth of cities is intensifying its impact on people and the environment through: • increased use of energy for the heating and cooling of more buildings, leading to urban heat islands and more greenhouse gas emissions • increased amount of hard surfaces contributing to higher temperatures in cities and more stormwater runoff • degraded air quality and noise impact • reduced urban biodiversity • compromised health and general well-being of people Basic Strategies In many design situations boundaries and constraints limit the application of cutting EDGe actions. In these circumstances designers should at least consider the following: • Consider green roofs early in the design process in consultation with all stakeholders to enable maximised integration with building systems and to mitigate building cost (avoid constructing as a retrofit). • Design of the green roof as part of a building’s structural, mechanical and hydraulic systems could lead to structural efficiency, the ability to optimise cooling benefits and better integrated water recycling systems. • Inform the selection of the type of green roof by considering its function, for example designing for social activity, required maintenance/access regime, recycling of water or habitat regeneration or a combination of uses. • Evaluate existing surroundings to determine possible links to the natural environment and choice of vegetation for the green roof with availability of local plant supply and expertise. Cutting EDGe Strategies • Create green roofs to contribute positively to the environment through reduced urban heat island effect and building temperatures, to improved stormwater quality, increased natural habitats, provision of social spaces and opportunity for increased local food supply. • Maximise solar panel efficiency by incorporating with design of green roof. • Integrate multiple functions for a single green roof such as grey water recycling, food production, more bio-diverse plantings, air quality improvement and provision of delightful spaces for social interaction. Synergies & references • BEDP Environment Design Guide DES 53: Roof and Facade Gardens GEN 4: Positive Development – designing for Net Positive Impacts TEC 26: Living Walls - a way to green the built environment • Green Roofs Australia: www.greenroofs.wordpress.com • International Green Roof Association: www.igra-world.com • Green Roofs for Healthy Cities (USA): www.greenroofs.org • Centre for Urban Greenery and Ecology (Singapore): http://research.cuge.com.sg

Infrastructure sustainability : vulnerability of axially loaded columns subjected to transverse impact loads

Increased industrialisation has brought to the forefront the susceptibility of concrete columns in both buildings and bridges to vehicle impacts. Accurate vulnerability assessments are crucial in the design process due to possible catastrophic nature of the failures that can cause. This chapter reports on research undertaken to investigate the impact capacity of the columns of low to medium raised building designed according to the Australian standards. Numerical simulation techniques were used in the process and validation was done by using experimental results published in the literature. The investigation thus far has confirmed that vulnerability of typical columns in five story buildings located in urban areas to medium velocity car impacts and hence these columns need to be re-designed or retrofitted. In addition, accuracy of the simplified method presented in EN 1991-1-7 to quantify the impact damage was scrutinised. A simplified concept to assess the damage due to all collisions modes was introduced. The research information will be extended to generate a common data base to assess the vulnerability of columns in urban areas against new generation of vehicles.

Remediation strategies of shaft and common mode voltages in adjustable speed drive systems

AC motors are largely used in a wide range of modern systems, from household appliances to automated industry applications such as: ventilations systems, fans, pumps, conveyors and machine tool drives. Inverters are widely used in industrial and commercial applications due to the growing need for speed control in ASD systems. Fast switching transients and the common mode voltage, in interaction with parasitic capacitive couplings, may cause many unwanted problems in the ASD applications. These include shaft voltage and leakage currents. One of the inherent characteristics of Pulse Width Modulation (PWM) techniques is the generation of the common mode voltage, which is defined as the voltage between the electrical neutral of the inverter output and the ground. Shaft voltage can cause bearing currents when it exceeds the amount of breakdown voltage level of the thin lubricant film between the inner and outer rings of the bearing. This phenomenon is the main reason for early bearing failures. A rapid development in power switches technology has lead to a drastic decrement of switching rise and fall times. Because there is considerable capacitance between the stator windings and the frame, there can be a significant capacitive current (ground current escaping to earth through stray capacitors inside a motor) if the common mode voltage has high frequency components. This current leads to noises and Electromagnetic Interferences (EMI) issues in motor drive systems. These problems have been dealt with using a variety of methods which have been reported in the literature. However, cost and maintenance issues have prevented these methods from being widely accepted. Extra cost or rating of the inverter switches is usually the price to pay for such approaches. Thus, the determination of cost-effective techniques for shaft and common mode voltage reduction in ASD systems, with the focus on the first step of the design process, is the targeted scope of this thesis. An introduction to this research – including a description of the research problem, the literature review and an account of the research progress linking the research papers – is presented in Chapter 1. Electrical power generation from renewable energy sources, such as wind energy systems, has become a crucial issue because of environmental problems and a predicted future shortage of traditional energy sources. Thus, Chapter 2 focuses on the shaft voltage analysis of stator-fed induction generators (IG) and Doubly Fed Induction Generators DFIGs in wind turbine applications. This shaft voltage analysis includes: topologies, high frequency modelling, calculation and mitigation techniques. A back-to-back AC-DC-AC converter is investigated in terms of shaft voltage generation in a DFIG. Different topologies of LC filter placement are analysed in an effort to eliminate the shaft voltage. Different capacitive couplings exist in the motor/generator structure and any change in design parameters affects the capacitive couplings. Thus, an appropriate design for AC motors should lead to the smallest possible shaft voltage. Calculation of the shaft voltage based on different capacitive couplings, and an investigation of the effects of different design parameters are discussed in Chapter 3. This is achieved through 2-D and 3-D finite element simulation and experimental analysis. End-winding parameters of the motor are also effective factors in the calculation of the shaft voltage and have not been taken into account in previous reported studies. Calculation of the end-winding capacitances is rather complex because of the diversity of end winding shapes and the complexity of their geometry. A comprehensive analysis of these capacitances has been carried out with 3-D finite element simulations and experimental studies to determine their effective design parameters. These are documented in Chapter 4. Results of this analysis show that, by choosing appropriate design parameters, it is possible to decrease the shaft voltage and resultant bearing current in the primary stage of generator/motor design without using any additional active and passive filter-based techniques. The common mode voltage is defined by a switching pattern and, by using the appropriate pattern; the common mode voltage level can be controlled. Therefore, any PWM pattern which eliminates or minimizes the common mode voltage will be an effective shaft voltage reduction technique. Thus, common mode voltage reduction of a three-phase AC motor supplied with a single-phase diode rectifier is the focus of Chapter 5. The proposed strategy is mainly based on proper utilization of the zero vectors. Multilevel inverters are also used in ASD systems which have more voltage levels and switching states, and can provide more possibilities to reduce common mode voltage. A description of common mode voltage of multilevel inverters is investigated in Chapter 6. Chapter 7 investigates the elimination techniques of the shaft voltage in a DFIG based on the methods presented in the literature by the use of simulation results. However, it could be shown that every solution to reduce the shaft voltage in DFIG systems has its own characteristics, and these have to be taken into account in determining the most effective strategy. Calculation of the capacitive coupling and electric fields between the outer and inner races and the balls at different motor speeds in symmetrical and asymmetrical shaft and balls positions is discussed in Chapter 8. The analysis is carried out using finite element simulations to determine the conditions which will increase the probability of high rates of bearing failure due to current discharges through the balls and races.

Developing managers as researchers using a learning cohort approach

This paper describes the design process and curriculum for a learning cohort of eight managers who came from public and private providers of vocational education and training. While the authors found no discussion on developing research knowledge and skills of managers using learning cohorts, the general learning cohorts literature provided a number of recommendations for learning cohort design. The initial stages of the learning cohort were evaluated. The results highlighted the importance of clarifying the psychological contract and its use in self-selection, supported the recommendations in the literature of the significance of the careful design and implementation of an initial residential workshop and also found support for further residential workshops of a similar design. The attendance of the cohort members in tow faculty wide core research units drew mixed comments.

Intelligent physical modelling systems - Why?

“What did you think you were doing?” Was the question posed by the conference organizers to me as the inventor and constructor of the first working Tangible Interfaces over 40 years ago. I think the question was intended to encourage me to talk about the underlying ideas and intentionality rather than describe an endless sequence of electronic bricks and that is what I shall do in this presentation. In the sixties the prevalent idea for a graphics interface was an analogue with sketching which was to somehow be understood by the computer as three dimensional form. I rebelled against this notion for reasons which I will explain in the presentation and instead came up with tangible physical three dimensional intelligent objects. I called these first prototypes “Intelligent Physical Modelling Systems” which is a really dumb name for an obvious concept. I am eternally grateful to Hiroshi Ishii for coining the term “Tangible User Interfaces” - the same idea but with a much smarter name. Another motivator was user involvement in the design process, and that led to the Generator (1979) project with Cedric Price for the world’s first intelligent building capable of organizing itself in response to the appetites of the users. The working model of that project is in MoMA. And the same motivation led to a self builders design kit (1980) for Walter Segal which facilitated self-builders to design their own houses. And indeed as the organizer’s question implied, the motivation and intentionality of these projects developed over the years in step with advancing technology. The speaker will attempt to articulate these changes with medical, psychological and educational examples. Much of this later work indeed stemming from the Media Lab where we are talking. Related topics such as “tangible thinking” and “intelligent teacups” will be introduced and the presentation will end with some speculations for the future. The presentation will be given against a background of images of early prototypes many of which have never been previously published.

Full Circle : a collection of prototypes

This exhibition engages with one of the key issues facing the fashion textiles industry in terms of future sustainability: that of the well being of fashion industry workers in Australia and New Zealand (people). This collection formed the basis of my honours dissertation (completed in New Zealand in 2008) which examines the contribution that design can make to sustainable manufacturing; particularly design for local production and consumption. An important aspect this work is the discussion of source, the work suggests that the made in China syndrome (in reference to the current state of over-consumerism in Australia and New Zealand) could be bought to a close through design to minimize waste and maximize opportunity for ‘people’: in this case both garment workers and the SMEs that employ them. The garments reflect the possibilities of focusing on a local approach that could be put into practice by a framework of SMEs that already exist. In addition the design process is highly transferrable and could be put into practice almost anywhere with minimal set up costs and a design ethos that progresses at the same pace as the skills of workers. This collection is a physical and conceptual embodiment of a source local/make local/sell local approach. The collection is an example of design that demonstrates that this is not an unrealistic ideal and is in fact possible through the development of a sustainable industry, in the sense of people, profit and planet, through adoption of a design process model that stops the waste at the source, by making better use of the raw materials and labour involved in making fashion garments. Although the focus of this research appears to centre on people and profit, this kind of source local/make local/sell local approach also has great benefits in terms of environmental sustainability.

The development of urban river corridors in Malaysia

Malaysian urban river corridors are facing major physical transformations in the 21st century. The effects of rapid development exacerbated by the competition between two key industry sectors, commercial base and tourism development in conjunction with urbanisation and industrialisation, have posted a high demand for the uses of these spaces. The political scenario and lack on consideration of ecological principles in its design solution have sparked stiff environmental and cultural constraint towards its landscape character as well as the ecological system. Therefore, a holistic approach towards improving the landscape design processes is extremely necessary to protect values of these places. Limited research has been carried out and further has created an urgent need to explore better ways to improve the landscape design processes of Malaysian urban river corridor developments that encompass the needs and aspirations of its multi-ethnic society without making any drastic changes to the landscape character of the rivers. This paper provides a brief introduction to address this significant gap and hence serves to contribute to the literature review.

Methodology for evaluating the landscape character of Malaysian heritage urban river corridors

The effects of rapid development have increased pressures on these places exacerbated by the competition between two key industry sectors, commercial base and tourism development. This, in supplement with urbanisation and industrialisation, has posted a high demand for the uses of these spaces. The political scenario and lack of adaptation on ecological principles and public participations in its design approach have sparked stiff environmental, historical and cultural constraint towards its landscape character as well as the ecological system. Therefore, a holistic approach towards improving the landscape design process is extremely necessary to protect human well being, cultural, environmental and historical values of these places. Limited research also has been carried out to overcome this situation. This further has created an urgent need to explore better ways to improve the landscape design process of Malaysian heritage urban river corridor developments that encompass the needs and aspirations of the Malaysian multi-ethnic society without making any drastic changes to the landscape character of the rivers. This paper presents a methodology to develop an advanced Landscape Character Assessment (aLCA) framework for evaluating the landscape character of the places, derived from the perception of two keys yet oppositional stakeholders: urban design team and special interest public. The triangulation of subjectivist paradigm methodologies: the psychophysical approach; the psychological approach; and, the phenomenological approach will be employed. The outcome will be used to improve the present landscape design process for future development of these places. Unless a range of perspectives can be brought to bear on enhancing the form and function of their future development and management, urban river corridors in the Malaysian context will continue to decline.

Sustainability factors in Industrialised Building System

In Malaysia, Industrialised Building Systems (IBS) are being promoted as a potential to enhance sustainability by the building industry and government. Known elsewhere as prefabricated construction, IBS employs a combination of ready-made components in the construction of buildings that promote quality of production, enhance simplification of construction processes and minimise on-site work. The components are manufactured in a factory either on or off site. They are then positioned and assembled into building structures. The unique characteristic of IBS has the potential to respond well to the sustainability challenge facing the construction industry. Despite the promises however, IBS has yet to be effectively implemented in Malaysia. There are often misconceptions among key stakeholders about IBS applications and some of the rating schemes fail to assess IBS towards sustainability deliverables. A holistic approach to improving IBS implementation is necessary to consider sustainability perceptions on IBS among key stakeholders. As IBS design is one of the most important development phases to incorporate sustainability requirements and expectations, a framework of embedding sustainability factors into IBS design is being developed through research. This paper presents an improved IBS design process focused on sustainability, showing where and how sustainability should be assessed to improve IBS construction. The framework being developed can provide guidance and decision making assistance to not only design consultants but all relevant stakeholders by integrating sustainability concepts into IBS applications. Outcome of the research will also provide a benchmark for developing countries in adopting prefabricated construction systems.

Public sector strategy classification system for shared service identification

The purpose of this conceptual paper is to address the lack of consistent means through which strategies are identified and discussed across theoretical perspectives in the field of business strategy. A standardised referencing system is offered to codify the means by which strategies can be identified, from which new business services and information systems may be derived. This taxonomy was developed using qualitative content analysis study of government agencies’ strategic plans. This taxonomy is useful for identifying strategy formation and determining gaps and opportunities. Managers will benefit from a more transparent strategic design process that reduces ambiguity, aids in identifying and correcting gaps in strategy formulation, and fosters enhanced strategic analysis. Key benefits to academics are the improved dialogue in strategic management field and suggest that progress in the field requires that fundamentals of strategy formulation and classification be considered more carefully. Finally, the formalization of strategy can lead to the clear identification of new business services, which inform ICT investment decisions and shared service prioritisation.