Ironless wheel motor for a direct drive vehicle application

An ironless motor for use as direct wheel drive is presented. The motor is intended for use in a lightweight (600kg), low drag, series hybrid commuter vehicle under development at The University of Queensland. The vehicle will utilise these ironless motors in each of its rear wheels, with each motor producing a peak torque output of 500Nm and a maximum rotational speed of 1500rpm. The axial flux motor consists of twin Ironless litz wire stators with a central magnetic ring and simplified Halbach magnet arrays on either side. A small amount of iron is used to support the outer Halbach arrays and to improve the peak magnetic flux density. Ducted air cooling is used to remove heat from the motor and will allow for a continuous torque rating of 250Nm. Ironless machines have previously been shown to be effective in high speed, high frequency applications (+1000Hz). They are generally regarded as non-optimal for low speed applications as iron cores allow for better magnet utilisation and do not significantly increase the weight of a machine. However, ironless machines can also be seen to be effective in applications where the average torque requirement is much lower than the peak torque requirement such as in some vehicle drive applications. The low spinning losses in ironless machines are shown to result in very high energy throughput efficiency in a wide range of vehicle driving cycles.

Implementation of a better choice healthy food and drink supply strategy for staff and visitors in government owned health facilities in Queensland, Australia

Objective The present paper reports on a quality improvement activity examining implementation of A Better Choice Healthy Food and Drink Supply Strategy for Queensland Health Facilities (A Better Choice). A Better Choice is a policy to increase supply and promotion of healthy foods and drinks and decrease supply and promotion of energy-dense, nutrient-poor choices in all food supply areas including food outlets, staff dining rooms, vending machines, tea trolleys, coffee carts, leased premises, catering, fundraising, promotion and advertising. Design An online survey targeted 278 facility managers to collect self-reported quantitative and qualitative data. Telephone interviews were sought concurrently with the twenty-five A Better Choice district contact officers to gather qualitative information. Setting Public sector-owned and -operated health facilities in Queensland, Australia. Subjects One hundred and thirty-four facility managers and twenty-four district contact officers participated with response rates of 48·2 % and 96·0 %, respectively. Results Of facility managers, 78·4 % reported implementation of more than half of the A Better Choice requirements including 24·6 % who reported full strategy implementation. Reported implementation was highest in food outlets, staff dining rooms, tea trolleys, coffee carts, internal catering and drink vending machines. Reported implementation was more problematic in snack vending machines, external catering, leased premises and fundraising. Conclusions Despite methodological challenges, the study suggests that policy approaches to improve the food and drink supply can be implemented successfully in public-sector health facilities, although results can be limited in some areas. A Better Choice may provide a model for improving food supply in other health and workplace settings.

Improved sub-cellular resolution via simultaneous analysis of organelle proteomics data across varied experimental conditions

Spatial organisation of proteins according to their function plays an important role in the specificity of their molecular interactions. Emerging proteomics methods seek to assign proteins to sub-cellular locations by partial separation of organelles and computational analysis of protein abundance distributions among partially separated fractions. Such methods permit simultaneous analysis of unpurified organelles and promise proteome-wide localisation in scenarios wherein perturbation may prompt dynamic re-distribution. Resolving organelles that display similar behavior during a protocol designed to provide partial enrichment represents a possible shortcoming. We employ the Localisation of Organelle Proteins by Isotope Tagging (LOPIT) organelle proteomics platform to demonstrate that combining information from distinct separations of the same material can improve organelle resolution and assignment of proteins to sub-cellular locations. Two previously published experiments, whose distinct gradients are alone unable to fully resolve six known protein-organelle groupings, are subjected to a rigorous analysis to assess protein-organelle association via a contemporary pattern recognition algorithm. Upon straightforward combination of single-gradient data, we observe significant improvement in protein-organelle association via both a non-linear support vector machine algorithm and partial least-squares discriminant analysis. The outcome yields suggestions for further improvements to present organelle proteomics platforms, and a robust analytical methodology via which to associate proteins with sub-cellular organelles.

A Near-Infrared Reflectance Spectroscopy Method for Direct Analysis of Several Chemical Components and Properties of Fruit, for Example, Chinese Hawthorn

Near-infrared spectroscopy (NIRS) calibrations were developed for the discrimination of Chinese hawthorn (Crataegus pinnatifida Bge. var. major) fruit from three geographical regions as well as for the estimation of the total sugar, total acid, total phenolic content, and total antioxidant activity. Principal component analysis (PCA) was used for the discrimination of the fruit on the basis of their geographical origin. Three pattern recognition methods, linear discriminant analysis, partial least-squares-discriminant analysis, and back-propagation artificial neural networks, were applied to classify and compare these samples. Furthermore, three multivariate calibration models based on the first derivative NIR spectroscopy, partial least-squares regression, back-propagation artificial neural networks, and least-squares-support vector machines, were constructed for quantitative analysis of the four analytes, total sugar, total acid, total phenolic content, and total antioxidant activity, and validated by prediction data sets.

Interestingness Measures for Multi-Level Association Rules

Association rule mining is one technique that is widely used when querying databases, especially those that are transactional, in order to obtain useful associations or correlations among sets of items. Much work has been done focusing on efficiency, effectiveness and redundancy. There has also been a focusing on the quality of rules from single level datasets with many interestingness measures proposed. However, with multi-level datasets now being common there is a lack of interestingness measures developed for multi-level and cross-level rules. Single level measures do not take into account the hierarchy found in a multi-level dataset. This leaves the Support-Confidence approach, which does not consider the hierarchy anyway and has other drawbacks, as one of the few measures available. In this chapter we propose two approaches which measure multi-level association rules to help evaluate their interestingness by considering the database’s underlying taxonomy. These measures of diversity and peculiarity can be used to help identify those rules from multi-level datasets that are potentially useful.

Towards bio-inspired place recognition over multiple spatial scales

This paper presents a new multi-scale place recognition system inspired by the recent discovery of overlapping, multi-scale spatial maps stored in the rodent brain. By training a set of Support Vector Machines to recognize places at varying levels of spatial specificity, we are able to validate spatially specific place recognition hypotheses against broader place recognition hypotheses without sacrificing localization accuracy. We evaluate the system in a range of experiments using cameras mounted on a motorbike and a human in two different environments. At 100% precision, the multiscale approach results in a 56% average improvement in recall rate across both datasets. We analyse the results and then discuss future work that may lead to improvements in both robotic mapping and our understanding of sensory processing and encoding in the mammalian brain.

Awareness of risky behaviour among Chinese drivers

Background In China, as in many developing countries, rapid increases in car ownership and new drivers have been coupled with a large trauma burden. The World Health Organization has identified key risk factors including speeding, drink-driving, helmet and restraint non-use, overloaded vehicles, and fatigued-driving in many rapidly motorising countries, including China. Levels of awareness of these risk factors among road users are not well understood. Although research identifies speeding as the major factor contributing to road crashes in China, there appears to be widespread acceptance of it among the broader community. Purpose To assess self-reported speeding and awareness of crash risk factors among Chinese drivers in Beijing. Methods Car drivers (n=299) were recruited from car washing locations and car parks to complete an anonymous questionnaire. Perceptions of the relative risk of drink-driving, fatigued-driving and speeding, and attitudes towards speeding and self-reported driving speeds were assessed. Results Overall, driving speeds of >10km/hr above posted limits on two road types (60 and 80 km/hour zones) were reported by more than one third of drivers. High-range speeding (i.e., >30 km/hour in a 60 km/hour zone and >40 km/hour in an 80 km/hour zone) was reported by approximately 5% of the sample. Attitudinal measures indicated that approximately three quarters of drivers reported attitudes that were not supportive of speeding. Drink-driving was identified as the most risky behaviour; 18% reported the perception that drink-driving had the same level of danger as speeding and 82% reported it as more dangerous. For fatigued-driving, 1% reported the perception that it was not as dangerous as speeding; 27.4% reported it as the same level and 71.6% perceived it as more dangerous. Conclusion Driving speeds well above posted speed limits were commonly reported by drivers. Speeding was rated as the least dangerous on-road behaviour, compared to drink-driving and fatigued-driving. One third of drivers reported regularly engaging in speeds at least 10km/hr above posted limits, despite speeding being the major reported contributor to crashes. Greater awareness of the risks associated with speeding is needed to help reduce the road trauma burden in China and promote greater speed limit compliance.

Bike share's impact on car use : evidence from the United States, Great Britain, and Australia

There are currently more than 400 cities operating bike share programs. Purported benefits of bike share programs include flexible mobility, physical activity, reduced congestion, emissions and fuel use. Implicit or explicit in the calculation of program benefits are assumptions regarding the modes of travel replaced by bike share journeys. This paper examines the degree to which car trips are replaced by bike share, through an examination of survey and trip data from bike share programs in Melbourne, Brisbane, Washing, D.C., London, and Minneapolis/St. Paul. A secondary and unique component of this analysis examines motor vehicle support services required for bike share fleet rebalancing and maintenance. These two components are then combined to estimate bike share’s overall contribution to changes in vehicle kilometres traveled. The results indicate that the estimated mean reduction in car use due to bike share is at least twice the distance covered by operator support vehicles, with the exception of London, in which the relationship is reversed, largely due to a low car mode substitution rate. As bike share programs mature, evaluation of their effectiveness in reducing car use may become increasingly important. This paper reveals that by increasing the convenience of bike share relative to car use and by improving perceptions of safety, the capacity of bike share programs to reduce vehicle trips and yield overall net benefits will be enhanced. Researchers can adapt the analytical approach proposed in this paper to assist in the evaluation of current and future bike share programs.

Architecture and affect

Invited Lecture for Interdisciplinary seminar, Yale School of Architecture. Seminar investigates architectural techniques of affect; topics included Adrian Stokes, Freud on aggression, Spinoza, German aesthetics, viscerality, Guattari and “concrete machines”; Other Invited guests: Peggy Deamer, Brian Massumi, Gary Genosko, Ernst Prelinger, Elizabeth Grosz, Ed Mitchell.

A comparative study of the semi-elastic and fully-elastic MapReduce models

MapReduce is a computation model for processing large data sets in parallel on large clusters of machines, in a reliable, fault-tolerant manner. A MapReduce computation is broken down into a number of map tasks and reduce tasks, which are performed by so called mappers and reducers, respectively. The placement of the mappers and reducers on the machines directly affects the performance and cost of the MapReduce computation in cloud computing. From the computational point of view, the mappers/reducers placement problem is a generation of the classical bin packing problem, which is NP-complete. Thus, in this paper we propose a new heuristic algorithm for the mappers/reducers placement problem in cloud computing and evaluate it by comparing with other several heuristics on solution quality and computation time by solving a set of test problems with various characteristics. The computational results show that our heuristic algorithm is much more efficient than the other heuristics and it can obtain a better solution in a reasonable time. Furthermore, we verify the effectiveness of our heuristic algorithm by comparing the mapper/reducer placement for a benchmark problem generated by our heuristic algorithm with a conventional mapper/reducer placement which puts a fixed number of mapper/reducer on each machine. The comparison results show that the computation using our mapper/reducer placement is much cheaper than the computation using the conventional placement while still satisfying the computation deadline.

A hybrid genetic algorithm for the energy-efficient virtual machine placement problem in data centers

Server consolidation using virtualization technology has become an important technology to improve the energy efficiency of data centers. Virtual machine placement is the key in the server consolidation technology. In the past few years, many approaches to the virtual machine placement have been proposed. However, existing virtual machine placement approaches consider the energy consumption by physical machines only, but do not consider the energy consumption in communication network, in a data center. However, the energy consumption in the communication network in a data center is not trivial, and therefore should be considered in the virtual machine placement. In our preliminary research, we have proposed a genetic algorithm for a new virtual machine placement problem that considers the energy consumption in both physical machines and the communication network in a data center. Aiming at improving the performance and efficiency of the genetic algorithm, this paper presents a hybrid genetic algorithm for the energy-efficient virtual machine placement problem. Experimental results show that the hybrid genetic algorithm significantly outperforms the original genetic algorithm, and that the hybrid genetic algorithm is scalable.

Wide area controls for transient and dynamic stability enhancement

This paper presents a study done into the effectiveness of using local acceleration measurements vs. remote angle measurements in providing stabilising control via SVCs following large disturbances. The system studied was an analogue of the Queensland-New South Wales Interconnection (QNI) and involved the control of an existing Static Var Compensators (SVC) at Sydney West. This study is placed in the context of wide area controls for large systems using aggregated models for groups of machines.

Acoustic emission condition monitoring : an application for wind turbine fault detection

Low speed rotating machines which are the most critical components in drive train of wind turbines are often menaced by several technical and environmental defects. These factors contribute to mount the economic requirement for Health Monitoring and Condition Monitoring of the systems. When a defect is happened in such system result in reduced energy loss rates from related process and due to it Condition Monitoring techniques that detecting energy loss are very difficult if not possible to use. However, in the case of Acoustic Emission (AE) technique this issue is partly overcome and is well suited for detecting very small energy release rates. Acoustic Emission (AE) as a technique is more than 50 years old and in this new technology the sounds associated with the failure of materials were detected. Acoustic wave is a non-stationary signal which can discover elastic stress waves in a failure component, capable of online monitoring, and is very sensitive to the fault diagnosis. In this paper the history and background of discovering and developing AE is discussed, different ages of developing AE which include Age of Enlightenment (1950-1967), Golden Age of AE (1967-1980), Period of Transition (1980-Present). In the next section the application of AE condition monitoring in machinery process and various systems that applied AE technique in their health monitoring is discussed. In the end an experimental result is proposed by QUT test rig which an outer race bearing fault was simulated to depict the sensitivity of AE for detecting incipient faults in low speed high frequency machine.

Deleuze and music : a creative approach to the study of music

The work of Gilles Deleuze has influenced an increasing number of music scholars and practicing musicians, particularly those interested in experimental, electronic and popular music. This is despite the notoriously complex nature of his writings, and the specialised theoretical vocabulary that he employs. This thesis both demystifies some of the key terms and concepts of this vocabulary, before demonstrating how Deleuze’s ideas may be put to work in new and fruitful ways; this is achieved with specific reference to the relationships that music has with thought, time and machines. In Chapter 1, Deleuze’s understanding of the power of thought is examined, in particular his approach to communication, transcendence and immanence, and the “powers of thought.” Each of these concepts helps us to understand Deleuze’s work within broad problem of how to think about music immanently: that is, how to maintain that thought and music are both immanent aspects of life and experience. Chapter 2 examines time within a Deleuzian framework, linking his work on cinema with the concept of the “refrain”; both of these areas prove crucial to his understanding of music, as seen in Deleuze’s approach to the work of Varese, Messiaen, and Boulez. In addition, Deleuze’s understanding of time proves fruitful in examining various aspects of music production, as seen in contemporary electronic dance music. Finally, Chapter 3 looks at the concept of the machine, as developed by Deleuze and Guattari, with reference to the sorts of “machinic” connections that a Deleuzian approach encourages us to seek out in music. Once again, examples from contemporary electronic music are presented, in relation to the notions of becoming and subjectivity. Throughout these chapters, Deleuze’s broad understanding of philosophy as the “creation of concepts” is deployed. This means introducing new ideas and specific types of music that encourage creative and novel engagements with the study of music.

The role of laboratory exercises in modern power engineering education at the University of Queensland

The University of Queensland (UQ) has extensive laboratory facilities associated with each course in the undergraduate electrical engineering program. The laboratories include machines and drives, power systems simulation, power electronics and intelligent equipment diagnostics. A number of postgraduate coursework programs are available at UQ and the courses associated with these programs also use laboratories. The machine laboratory is currently being renovated with i-lab style web based experimental facilities, which could be remotely accessed. Senior level courses use independent projects using laboratory facilities and this is found to be very useful to improve students' learning skill. Laboratory experiments are always an integral part of a course. Most of the experiments are conducted in a group of 2-3 students and thesis projects in BE and major projects in ME are always individual works. Assessment is done in-class for the performance and also for the report and analysis.