How do you ‘teach’ sustainability to engineers? introducing the engineering sustainable solutions program

Environmental engineers are increasingly being required to have knowledge about sustainability in their professional careers. Accreditation mechanisms for including sustainability in degree program requirements exist and are gradually being implemented by Engineers Australia. However, true integration of sustainability material into higher and vocational education curricula is still low, particularly outside the environmental engineering degree programs. In addition to environmental engineering, it is crucial for engineering across the specialisations, to be exposed to sustainability concepts and theories. This paper will demonstrate how sustainability as a ‘critical literacy’ can be designed for teaching within mainstream engineering education, using a current Australian project as a case study. The project demonstrates that sustainability education for all engineers is not only possible, but that there is international interest in collaborating in such an educational initiative. A pilot trial of the Introductory Module was undertaken in Semester 1 2004 and Version 2 trials are now proceeding with a number of universities and organisations nationally and internationally. Further modules are currently being developed in collaboration with Engineers Australia and UNESCO. The program is a finalist in the 2005 Banksia Awards (Category 11, Environmental Leadership Education and Training).

Expression of a bacterial xylanase in Trichoderma reesei under the egl2 and cbh2 glycosyl hydrolase gene promoters

Expression vectors were constructed for Trichoderma reesei using the promoters, secretion signals and the modular structure of the efficiently expressed and secreted cellulase enzymes EGL2 (Cel5A) and CBH2 (Cel6A) as a prelude to establishing a platform where a gene of interest can be expressed under several promoters simultaneously. The designs featured (i) EGL2sigpro (egl2 promoter and secretion signal), (ii) EGL2cbmlin (egl2 promoter, secretion signal, EGL2 cellulose binding module and linker), (iii) CBH2sigpro (cbh2 promoter and secretion signal) and (iv) CBH2cbmlin (cbh2 promoter, secretion signal, CBH2 cellulose binding module and linker). Recombinant vectors were introduced individually into the high protein-secreting T. reesei RUT-C30 strain to generate single-promoter transformants expressing the Dictyoglomus thermophilum xynB gene that encodes a thermophilic xylanase enzyme (XynB). Ten transformants producing XynB representing each of the four different types of vectors were selected for further testing and the highest XynB production was achieved from a transformant containing 1–2 copies of the EGL2cbmlin vector. Best xylanase producers did not show any particular pattern in terms of the number of gene copies and their mode of integration into the chromosomal DNA. Transformants generated with the cbmlin-type vectors produced multiple forms of XynB which were decorated with various N- and O-glycans. One of the O-glycans was identified as hexuronic acid, whose presence had not been observed previously in the glycosylation patterns of T. reesei.

The impacts of FOREX fluctuations on construction business performance : an organisational capabilities perspective

Construction projects are a high risk business activity. When undertaking projects in an international context, it is further complicated by the risk of fluctuations in the foreign exchange rates (FOREX). Construction business performance is affected by these fluctuations. They affect progress and cause delays, which in turn create problems for subcontractors, namely cost overruns, disputes, arbitration, total abandonment and litigation. FOREX fluctuations also cause the price of raw materials to increase, leading the cost overruns. Managing FOREX risk is critical and past research have focused on the need for adequate insurance, careful planning and management, and foreign exchange futures hedging to overcome issues that have been caused by the FOREX risk. Analysis of FOREX risk in international construction business usually focused only on issues at the project level. There is currently lack of understanding of Organisational Capabilities (OC) to manage the impacts of FOREX risk, which when examined, are seen in isolation. This paper attempts to bridge the gap by discussing the impacts of FOREX fluctuations on the international construction business. The focus is on the OC perspective and the need to develop OC framework to mitigate the risk in sustaining construction business performance.

Security properties analysis in a TPM-based protocol

Security protocols are designed in order to provide security properties (goals). They achieve their goals using cryptographic primitives such as key agreement or hash functions. Security analysis tools are used in order to verify whether a security protocol achieves its goals or not. The analysed property by specific purpose tools are predefined properties such as secrecy (confidentiality), authentication or non-repudiation. There are security goals that are defined by the user in systems with security requirements. Analysis of these properties is possible with general purpose analysis tools such as coloured petri nets (CPN). This research analyses two security properties that are defined in a protocol that is based on trusted platform module (TPM). The analysed protocol is proposed by Delaune to use TPM capabilities and secrets in order to open only one secret from two submitted secrets to a recipient

Feasibility and efficacy of a church-based intervention to promote physical activity in children

Background This study evaluated the feasibility and preliminary efficacy of a church-based intervention to promote physical activity (PA) in children. Methods The study was conducted in 4 churches located in 2 large metropolitan areas and 2 regional towns in Kansas. Churches in the intervention condition implemented the "Shining Like Stars" physical activity curriculum module during their regularly scheduled Sunday school classes. Churches in the control condition delivered the same content without integrating physical activity into the lessons. In addition to the curriculum, the intervention churches completed a series of weekly family devotional activities designed to promote parental support for PA and increase PA outside of Sunday school. Results Children completing the Shining Like Stars curriculum exhibited significantly greater amounts of MVPA than those in the control condition (20 steps/min vs. 7 steps/min). No intervention effects were observed for PA levels outside of Sunday school or parental support for PA; however, relative to controls, children in the intervention churches did exhibit a significant reduction in screen time. Conclusion The findings confirm that the integration of physical activity into Sunday school is feasible and a potentially effective strategy for promoting PA in young children.

A variant of the breast cancer type 2 susceptibility protein (BRC) repeat is essential for the RECQL5 Helicase to interact with RAD51 Recombinase for genome stabilization

The BRC repeat is a structural motif in the tumor suppressor BRCA2 (breast cancer type 2 susceptibility protein), which promotes homologous recombination (HR) by regulating RAD51 recombinase activity. To date, the BRC repeat has not been observed in other proteins, so that its role in HR is inferred only in the context of BRCA2. Here, we identified a BRC repeat variant, named BRCv, in the RECQL5 helicase, which possesses anti-recombinase activity in vitro and suppresses HR and promotes cellular resistance to camptothecin-induced replication stress in vivo. RECQL5-BRCv interacted with RAD51 through two conserved motifs similar to those in the BRCA2-BRC repeat. Mutations of either motif compromised functions of RECQL5, including association with RAD51, inhibition of RAD51-mediated D-loop formation, suppression of sister chromatid exchange, and resistance to camptothecin-induced replication stress. Potential BRCvs were also found in other HR regulatory proteins, including Srs2 and Sgs1, which possess anti-recombinase activities similar to that of RECQL5. A point mutation in the predicted Srs2-BRCv disrupted the ability of the protein to bind RAD51 and to inhibit D-loop formation. Thus, BRC is a common RAD51 interaction module that can be utilized by different proteins to either promote HR, as in the case of BRCA2, or to suppress HR, as in RECQL5.

Analysis of two authorization protocols using Colored Petri Nets

To prevent unauthorized access to protected trusted platform module (TPM) objects, authorization protocols, such as the object-specific authorization protocol (OSAP), have been introduced by the trusted computing group (TCG). By using OSAP, processes trying to gain access to the protected TPM objects need to prove their knowledge of relevant authorization data before access to the objects can be granted. Chen and Ryan’s 2009 analysis has demonstrated OSAP’s authentication vulnerability in sessions with shared authorization data. They also proposed the Session Key Authorization Protocol (SKAP) with fewer stages as an alternative to OSAP. Chen and Ryan’s analysis of SKAP using ProVerif proves the authentication property. The purpose of this paper was to examine the usefulness of Colored Petri Nets (CPN) and CPN Tools for security analysis. Using OSAP and SKAP as case studies, we construct intruder and authentication property models in CPN. CPN Tools is used to verify the authentication property using a Dolev–Yao-based model. Verification of the authentication property in both models using the state space tool produces results consistent with those of Chen and Ryan.

Electrochemistry

Electrochemistry is a truly multidisciplinary science which can be applied to a variety of fields within the physical, chemical and biological sciences. This topic chapter details a selection of areas including energy conversion and storage in particular fuel cells and Li ion batteries; electrosynthesis which covers both organic synthesis and the electrodeposition of homogeneous as well as nanostructured surfaces; corrosion; electroanalytical chemistry in the classic sense of analyte detection as well as probing mechanistic information regarding oxidation/reduction reactions of electroactive species at the nanoscale. Finally the applicability of electrochemistry to the biological sciences is briefly described.

Development of gas sensing technology for ground and airborne applications powered by solar energy : methodology and experimental results

Monitoring gases for environmental, industrial and agricultural fields is a demanding task that requires long periods of observation, large quantity of sensors, data management, high temporal and spatial resolution, long term stability, recalibration procedures, computational resources, and energy availability. Wireless Sensor Networks (WSNs) and Unmanned Aerial Vehicles (UAVs) are currently representing the best alternative to monitor large, remote, and difficult access areas, as these technologies have the possibility of carrying specialised gas sensing systems, and offer the possibility of geo-located and time stamp samples. However, these technologies are not fully functional for scientific and commercial applications as their development and availability is limited by a number of factors: the cost of sensors required to cover large areas, their stability over long periods, their power consumption, and the weight of the system to be used on small UAVs. Energy availability is a serious challenge when WSN are deployed in remote areas with difficult access to the grid, while small UAVs are limited by the energy in their reservoir tank or batteries. Another important challenge is the management of data produced by the sensor nodes, requiring large amount of resources to be stored, analysed and displayed after long periods of operation. In response to these challenges, this research proposes the following solutions aiming to improve the availability and development of these technologies for gas sensing monitoring: first, the integration of WSNs and UAVs for environmental gas sensing in order to monitor large volumes at ground and aerial levels with a minimum of sensor nodes for an effective 3D monitoring; second, the use of solar energy as a main power source to allow continuous monitoring; and lastly, the creation of a data management platform to store, analyse and share the information with operators and external users. The principal outcomes of this research are the creation of a gas sensing system suitable for monitoring any kind of gas, which has been installed and tested on CH4 and CO2 in a sensor network (WSN) and on a UAV. The use of the same gas sensing system in a WSN and a UAV reduces significantly the complexity and cost of the application as it allows: a) the standardisation of the signal acquisition and data processing, thereby reducing the required computational resources; b) the standardisation of calibration and operational procedures, reducing systematic errors and complexity; c) the reduction of the weight and energy consumption, leading to an improved power management and weight balance in the case of UAVs; d) the simplification of the sensor node architecture, which is easily replicated in all the nodes. I evaluated two different sensor modules by laboratory, bench, and field tests: a non-dispersive infrared module (NDIR) and a metal-oxide resistive nano-sensor module (MOX nano-sensor). The tests revealed advantages and disadvantages of the two modules when used for static nodes at the ground level and mobile nodes on-board a UAV. Commercial NDIR modules for CO2 have been successfully tested and evaluated in the WSN and on board of the UAV. Their advantage is the precision and stability, but their application is limited to a few gases. The advantages of the MOX nano-sensors are the small size, low weight, low power consumption and their sensitivity to a broad range of gases. However, selectivity is still a concern that needs to be addressed with further studies. An electronic board to interface sensors in a large range of resistivity was successfully designed, created and adapted to operate on ground nodes and on-board UAV. The WSN and UAV created were powered with solar energy in order to facilitate outdoor deployment, data collection and continuous monitoring over large and remote volumes. The gas sensing, solar power, transmission and data management systems of the WSN and UAV were fully evaluated by laboratory, bench and field testing. The methodology created to design, developed, integrate and test these systems was extensively described and experimentally validated. The sampling and transmission capabilities of the WSN and UAV were successfully tested in an emulated mission involving the detection and measurement of CO2 concentrations in a field coming from a contaminant source; the data collected during the mission was transmitted in real time to a central node for data analysis and 3D mapping of the target gas. The major outcome of this research is the accomplishment of the first flight mission, never reported before in the literature, of a solar powered UAV equipped with a CO2 sensing system in conjunction with a network of ground sensor nodes for an effective 3D monitoring of the target gas. A data management platform was created using an external internet server, which manages, stores, and shares the data collected in two web pages, showing statistics and static graph images for internal and external users as requested. The system was bench tested with real data produced by the sensor nodes and the architecture of the platform was widely described and illustrated in order to provide guidance and support on how to replicate the system. In conclusion, the overall results of the project provide guidance on how to create a gas sensing system integrating WSNs and UAVs, how to power the system with solar energy and manage the data produced by the sensor nodes. This system can be used in a wide range of outdoor applications, especially in agriculture, bushfires, mining studies, zoology, and botanical studies opening the way to an ubiquitous low cost environmental monitoring, which may help to decrease our carbon footprint and to improve the health of the planet.

Computational fluid dynamics simulation and turbomachinery code validation of a high pressure ratio radial-inflow turbine

The present study explores reproducing the closest geometry of a high pressure ratio single stage radial-inflow turbine applied in the Sundstrans Power Systems T-100 Multipurpose Small Power Unit. The commercial software ANSYS-Vista RTD along with a built in module, BladeGen, is used to conduct a meanline design and create 3D geometry of one flow passage. Carefully examining the proposed design against the geometrical and experimental data, ANSYS-TurboGrid is applied to generate computational mesh. CFD simulations are performed with ANSYS-CFX in which three-dimensional Reynolds-Averaged Navier-Stokes equations are solved subject to appropriate boundary conditions. Results are compared with numerical and experimental data published in the literature in order to generate the exact geometry of the existing turbine and validate the numerical results against the experimental ones.

A modular matrix converter for transformer-less PMSG wind generation systems

An offshore wind turbine usually has the grid step-up transformer integrated in the nacelle. This increases mechanical loading of the tower. In that context, a transformer-less, high voltage, highly-reliable and compact converter system for nacelle installation would be an attractive solution for large offshore wind turbines. This paper, therefore, presents a transformer-less grid integration topology for PMSG based large wind turbine generator systems using modular matrix converters. Each matrix converter module is fed from three generator coils of the PMSG which are phase shifted by 120°. Outputs of matrix converter modules are connected in series to increase the output voltage and thus eliminate the need of a coupling step-up transformer. Moreover, dc-link capacitors found in conventional back-to-back converter topologies are eliminated in the proposed system. Proper multilevel output voltage generation and power sharing between converter modules are achieved through an advanced switching strategy. Simulation results are presented to validate the proposed modular matrix converter system, modulation method and control techniques.

A runtime integrity monitoring framework for real-time relative positioning systems based on GPS and DSRC

This paper provides a three-layered framework to monitor the positioning performance requirements of Real-time Relative Positioning (RRP) systems of the Cooperative Intelligent Transport Systems (C-ITS) that support Cooperative Collision Warning (CCW) applications. These applications exploit state data of surrounding vehicles obtained solely from the Global Positioning System (GPS) and Dedicated Short-Range Communications (DSRC) units without using other sensors. To this end, the paper argues the need for the GPS/DSRC-based RRP systems to have an autonomous monitoring mechanism, since the operation of CCW applications is meant to augment safety on roads. The advantages of autonomous integrity monitoring are essential and integral to any safety-of-life system. The autonomous integrity monitoring framework proposed necessitates the RRP systems to detect/predict the unavailability of their sub-systems and of the integrity monitoring module itself, and, if available, to account for effects of data link delays and breakages of DSRC links, as well as of faulty measurement sources of GPS and/or integrated augmentation positioning systems, before the information used for safety warnings/alarms becomes unavailable, unreliable, inaccurate or misleading. Hence, a monitoring framework using a tight integration and correlation approach is proposed for instantaneous reliability assessment of the RRP systems. Ultimately, using the proposed framework, the RRP systems will provide timely alerts to users when the RRP solutions cannot be trusted or used for the intended operation.

A biomechanical study of spherical grip

Use of the hand is vital in working life due to the grabbing and pinching it performs. Spherical grip is the most commonly used, due to similarity to the gripping of a computer mouse. Knowledge of its execution and the involved elements is essential. Analysis of this exertion with surface electromyography devices (to register muscular activity) and accelerometer devices (to register movement values ) can provide multiple variables. Six subjects performed ball gripping and registered real-time electromyography (thenar region, hypothenar region, first dorsal interosseous, flexors of the wrist, flexor carpi ulnaris and extensors of the wrist muscles) and accelerometer (thumb, index, middle, ring, pinky and palm) values. The obtained data was resampled “R software” and processed “Matlab Script” based on an automatic numerical sequence recognition program. Electromyography values were normalized on the basis of maximum voluntary contraction, whilst modular values were calculated for the acceleration vector. After processing and analysing the obtained data and signal, it was possible to identify five stages of movement in accordance with the module vector from the palm. The statistical analysis of the variables was descriptive: average and standard deviations. The outcome variables focus on the variations of the modules of the vector (between the maximum and minimum values of each module and phase) and the maximum values of the standardized electromyography of each muscle. Analysis of movement through accelerometer and electromyography variables can give us an insight into the operation of spherical grip. The protocol and treatment data can be used as a system to complement existing assessments in the hand.