A review of commuter exposure to ultrafine particles and its health effects

Ultrafine particles (UFPs, <100 nm) are produced in large quantities by vehicular combustion and are implicated in causing several adverse human health effects. Recent work has suggested that a large proportion of daily UFP exposure may occur during commuting. However, the determinants, variability and transport mode-dependence of such exposure are not well-understood. The aim of this review was to address these knowledge gaps by distilling the results of ‘in-transit’ UFP exposure studies performed to-date, including studies of health effects. We identified 47 exposure studies performed across 6 transport modes: automobile, bicycle, bus, ferry, rail and walking. These encompassed approximately 3000 individual trips where UFP concentrations were measured. After weighting mean UFP concentrations by the number of trips in which they were collected, we found overall mean UFP concentrations of 3.4, 4.2, 4.5, 4.7, 4.9 and 5.7 × 10^4 particles cm^-3 for the bicycle, bus, automobile, rail, walking and ferry modes, respectively. The mean concentration inside automobiles travelling through tunnels was 3.0 × 10^5 particles cm^-3. While the mean concentrations were indicative of general trends, we found that the determinants of exposure (meteorology, traffic parameters, route, fuel type, exhaust treatment technologies, cabin ventilation, filtration, deposition, UFP penetration) exhibited marked variability and mode-dependence, such that it is not necessarily appropriate to rank modes in order of exposure without detailed consideration of these factors. Ten in-transit health effects studies have been conducted and their results indicate that UFP exposure during commuting can elicit acute effects in both healthy and health-compromised individuals. We suggest that future work should focus on further defining the contribution of in-transit UFP exposure to total UFP exposure, exploring its specific health effects and investigating exposures in the developing world. Keywords: air pollution; transport modes; acute health effects; travel; public transport

An investigation of commuter exposure to ultrafine particles in Sydney

Commuting in various transport modes represents an activity likely to incur significant exposure to traffic emissions. This study investigated the determinants and characteristics of exposure to ultrafine (< 100 nm) particles (UFPs) in four transport modes in Sydney, with a specific focus on exposure in automobiles, which remain the transport mode of choice for approximately 70% of Sydney commuters. UFP concentrations were measured using a portable condensation particle counter (CPC) inside five automobiles commuting on above ground and tunnel roadways, and in buses, ferries and trains. Determinant factors investigated included wind speed, cabin ventilation (automobiles only) and traffic volume. The results showed that concentrations varied significantly as a consequence of transport mode, vehicle type and ventilation characteristics. The effects of wind speed were minimal relative to those of traffic volume (especially heavy diesel vehicles) and cabin ventilation, with the latter proving to be a strong determinant of UFP ingress into automobiles. The effect of ~70 minutes of commuting on total daily exposure was estimated using a range of UFP concentrations reported for several microenvironments. A hypothetical Sydney resident commuting by automobile and spending 8.5 minutes of their day in the M5 East tunnel could incur anywhere from a lower limit of 3-11% to an upper limit of 37-69% of daily UFP exposure during a return commute, depending on the concentrations they encountered in other microenvironments, the type of vehicle they used and the ventilation setting selected. However, commute-time exposures at either extreme of the values presented are unlikely to occur in practice. The range of exposures estimated for other transport modes were comparable to those of automobiles, and in the case of buses, higher than automobiles.

The rise of co-creative consumers : user experience sharing behaviour in online communities

This thesis examines consumer initiated value co-creation behaviour in the context of convergent mobile online services using a Service-Dominant logic (SD logic) theoretical framework. It focuses on non-reciprocal marketing phenomena such as open innovation and user generated content whereby new viable business models are derived and consumer roles and community become essential to the success of business. Attention to customers. roles and personalised experiences in value co-creation has been recognised in the literature (e.g., Prahalad & Ramaswamy, 2000; Prahalad, 2004; Prahalad & Ramaswamy, 2004). Similarly, in a subsequent iteration of their 2004 version of the foundations of SD logic, Vargo and Lusch (2006) replaced the concept of value co-production with value co-creation and suggested that a value co-creation mindset is essential to underpin the firm-customer value creation relationship. Much of this focus, however, has been limited to firm initiated value co-creation (e.g., B2B or B2C), while consumer initiated value creation, particularly consumer-to-consumer (C2C) has received little attention in the SD logic literature. While it is recognised that not every consumer wishes to make the effort to engage extensively in co-creation processes (MacDonald & Uncles, 2009), some consumers may not be satisfied with a standard product, instead they engage in the effort required for personalisation that potentially leads to greater value for themselves, and which may benefit not only the firm, but other consumers as well. Literature suggests that there are consumers who do, and as a result initiate such behaviour and expend effort to engage in co-creation activity (e.g., Gruen, Osmonbekov and Czaplewski, 2006; 2007 MacDonald & Uncles, 2009). In terms of consumers. engagement in value proposition (co-production) and value actualisation (co-creation), SD logic (Vargo & Lusch, 2004, 2008) provides a new lens that enables marketing scholars to transcend existing marketing theory and facilitates marketing practitioners to initiate service centric and value co-creation oriented marketing practices. Although the active role of the consumer is acknowledged in the SD logic oriented literature, we know little about how and why consumers participate in a value co-creation process (Payne, Storbacka, & Frow, 2008). Literature suggests that researchers should focus on areas such as C2C interaction (Gummesson 2007; Nicholls 2010) and consumer experience sharing and co-creation (Belk 2009; Prahalad & Ramaswamy 2004). In particular, this thesis seeks to better understand consumer initiated value co-creation, which is aligned with the notion that consumers can be resource integrators (Baron & Harris, 2008) and more. The reason for this focus is that consumers today are more empowered in both online and offline contexts (Füller, Mühlbacher, Matzler, & Jawecki, 2009; Sweeney, 2007). Active consumers take initiatives to engage and co-create solutions with other active actors in the market for their betterment of life (Ballantyne & Varey, 2006; Grönroos & Ravald, 2009). In terms of the organisation of the thesis, this thesis first takes a „zoom-out. (Vargo & Lusch, 2011) approach and develops the Experience Co-Creation (ECo) framework that is aligned with balanced centricity (Gummesson, 2008) and Actor-to-Actor worldview (Vargo & Lusch, 2011). This ECo framework is based on an extended „SD logic friendly lexicon. (Lusch & Vargo, 2006): value initiation and value initiator, value-in-experience, betterment centricity and betterment outcomes, and experience co-creation contexts derived from five gaps identified from the SD logic literature review. The framework is also designed to accommodate broader marketing phenomena (i.e., both reciprocal and non-reciprocal marketing phenomena). After zooming out and establishing the ECo framework, the thesis takes a zoom-in approach and places attention back on the value co-creation process. Owing to the scope of the current research, this thesis focuses specifically on non-reciprocal value co-creation phenomena initiated by consumers in online communities. Two emergent concepts: User Experience Sharing (UES) and Co-Creative Consumers are proposed grounded in the ECo framework. Together, these two theorised concepts shed light on the following two propositions: (1) User Experience Sharing derives value-in-experience as consumers make initiative efforts to participate in value co-creation, and (2) Co-Creative Consumers are value initiators who perform UES. Three research questions were identified underpinning the scope of this research: RQ1: What factors influence consumers to exhibit User Experience Sharing behaviour? RQ2: Why do Co-Creative Consumers participate in User Experience Sharing as part of value co-creation behaviour? RQ3: What are the characteristics of Co-Creative Consumers? To answer these research questions, two theoretical models were developed: the User Experience Sharing Behaviour Model (UESBM) grounded in the Theory of Planned Behaviour framework, and the Co-Creative Consumer Motivation Model (CCMM) grounded in the Motivation, Opportunity, Ability framework. The models use SD logic consistent constructs and draw upon multiple streams of literature including consumer education, consumer psychology and consumer behaviour, and organisational psychology and organisational behaviour. These constructs include User Experience Sharing with Other Consumers (UESC), User Experience Sharing with Firms (UESF), Enjoyment in Helping Others (EIHO), Consumer Empowerment (EMP), Consumer Competence (COMP), and Intention to Engage in User Experience Sharing (INT), Attitudes toward User Experience Sharing (ATT) and Subjective Norm (SN) in the UESBM, and User Experience Sharing (UES), Consumer Citizenship (CIT), Relating Needs of Self (RELS) and Relating Needs of Others (RELO), Newness (NEW), Mavenism (MAV), Use Innovativeness (UI), Personal Initiative (PIN) and Communality (COMU) in the CCMM. Many of these constructs are relatively new to marketing and require further empirical evidence for support. Two studies were conducted to underpin the corresponding research questions. Study One was conducted to calibrate and re-specify the proposed models. Study Two was a replica study to confirm the proposed models. In Study One, data were collected from a PC DIY online community. In Study Two, a majority of data were collected from Apple product online communities. The data were examined using structural equation modelling and cluster analysis. Considering the nature of the forums, the Study One data is considered to reflect some characteristics of Prosumers and the Study Two data is considered to reflect some characteristics of Innovators. The results drawn from two independent samples (N = 326 and N = 294) provide empirical support for the overall structure theorised in the research models. The results in both models show that Enjoyment in Helping Others and Consumer Competence in the UESBM, and Consumer Citizenship and Relating Needs in CCMM have significant impacts on UES. The consistent results appeared in both Study One and Study Two. The results also support the conceptualisation of Co-Creative Consumers and indicate Co-Creative Consumers are individuals who are able to relate the needs of themselves and others and feel a responsibility to share their valuable personal experiences. In general, the results shed light on "How and why consumers voluntarily participate in the value co-creation process?. The findings provide evidence to conceptualise User Experience Sharing behaviour as well as the Co-Creative Consumer using the lens of SD logic. This research is a pioneering study that incorporates and empirically tests SD logic consistent constructs to examine a particular area of the logic – that is consumer initiated value co-creation behaviour. This thesis also informs practitioners about how to facilitate and understand factors that engage with either firm or consumer initiated online communities.

Vacuum cleaner emissions as a source of indoor exposure to airborne particles and bacteria

Vacuuming can be a source of indoor exposure to biological and non-biological aerosols, although there is little data that describes the magnitude of emissions from the vacuum cleaner itself. We therefore sought to quantify emission rates of particles and bacteria from a large group of vacuum cleaners and investigate their potential determinants, including temperature, dust bags, exhaust filters, price and age. Emissions of particles between 0.009 and 20 µm and bacteria were measured from 21 vacuums. Ultrafine (<100 nm) particle emission rates ranged from 4.0 × 10^6 to 1.1 × 10^11 particles min-1. Emission of 0.54 to 20 µm particles ranged from 4.0 × 10^4 to 1.2 × 10^9 particles min-1. PM2.5 emissions were between 2.4 × 10-1 and 5.4 × 10^3 µg min-1. Bacteria emissions ranged from 0 to 7.4 × 10^5 bacteria min-1 and were poorly correlated with dust bag bacteria content and particle emissions. Large variability in emission of all parameters was observed across the 21 vacuums we assessed, which was largely not attributable to the range of determinant factors we assessed. Vacuum cleaner emissions contribute to indoor exposure to non-biological and biological aerosols when vacuuming, and this may vary markedly depending on the vacuum used.

Central Queensland Mining Supplies Pty Ltd v Columbia Steel Casting Co Ltd

In Central Queensland Mining Supplies Pty Ltd v Columbia Steel Casting Co Ltd [2011] QSC 183 Applegarth J considered complaints made by the defendant about the approach the plaintiff had taken in its endeavour to comply with its disclosure obligation under r 211 of the Uniform Civil Procedure Rules 1999 (Qld). The judgment also provides an indication of the direction the court is taking in relation to disclosure and document management in matters involving large numbers of documents.

The influence of architecture on degradation and tissue ingrowth into three-dimensional poly(lactic-co-glycolic acid) scaffolds in vitro and in vivo

The in vitro and in vivo degradation properties of poly(lactic-co-glycolic acid) (PLGA) scaffolds produced by two different technologies - thermally induced phase separation (TIPS), and solvent casting and particulate leaching (SCPL) were compared. Over 6 weeks, in vitro degradation produced changes in SCPL scaffold dimension, mass, internal architecture and mechanical properties. TIPS scaffolds produced far less changes in these parameters providing significant advantages over SCPL. In vivo results were based on a microsurgically created arteriovenous (AV) loop sandwiched between two TIPS scaffolds placed in a polycarbonate chamber under rat groin skin. Histologically, a predominant foreign body giant cell response and reduced vascularity was evident in tissue ingrowth between 2 and 8 weeks in TIPS scaffolds. Tissue death occurred at 8 weeks in the smallest pores. Morphometric comparison of TIPS and SCPL scaffolds indicated slightly better tissue ingrowth but greater loss of scaffold structure in SCPL scaffolds. Although advantageous in vitro, large surface area:volume ratios and varying pore sizes in PLGA TIPS scaffolds mean that effective in vivo (AV loop) utilization will only be achieved if the foreign body response can be significantly reduced so as to allow successful vascularisation, and hence sustained tissue growth, in pores less than 300 μm. © 2005 Elsevier Ltd. All rights reserved.

Investigating the future of project management : a co-word analysis approach

If Project Management (PM) is a well-accepted mode of managing organizations, more and more organizations are adopting PM in order to satisfy the diversified needs of application areas within a variety of industries and organizations. Concurrently, the number of PM practitioners and people involved at various level of qualification is vigorously rising. Thus the importance to characterize, define and understand this field and its underlying strength, basis and development is paramount. For this purpose we will referee to sociology of actor-networks and qualitative scientometrics leading to the choice of the co-word analysis method in enabling us to capture the project management field and its dynamics. Results of a study based on the analysis of EBSCO Business Source Premier Database will be presented and some future trends and scenarios proposed. The main following trends are confirmed, in alignment with previous studies: continuous interest for the “cost engineering” aspects, on going interest for Economic aspects and contracts, how to deal with various project types (categorizations), the integration with Supply Chain Management and Learning and Knowledge Management. Furthermore besides these continuous trends, we can note new areas of interest: the link between strategy and project, Governance, the importance of maturity (organizational performance and metrics, control) and Change Management. We see the actors (Professional Bodies, Governmental Bodies, Agencies, Universities, Industries, Researchers, and Practitioners) reinforcing their competing/cooperative strategies in the development of standards and certifications and moving to more “business oriented” relationships with their members and main stakeholders (Governments, Institutions like European Community, Industries, Agencies, NGOs…), at least at central level.

Child welfare policy and practice on children’s exposure to domestic violence

There are emerging movements in several countries to improve policy and practice to protect children from exposure to domestic violence. These movements have resulted in the collection of new data on EDV and the design and implementation of new child welfare policies and practices. To assist with the development of child welfare practice, this article summarizes current knowledge on the prevalence of EDV, and on child welfare services policies and practices that may hold promise for reducing the frequency and impact of EDV on children. We focus on Australia, Canada, and the United States, as these countries share a similar socio-legal context, a long history of enacting and expanding legislation about reporting of maltreatment, debates regarding the application of reporting laws to EDV, and new child welfare practices that show promise for responding more effectively to EDV.

Principles of taxation law (4th Edition)

Taxation law can be an incredibly complex subject to absorb, particularly when time is limited. Written specifically for students, Principles of Taxation Law 2011 brings much needed clarity to this area of law. Utilising many methods to make this often daunting subject achievable, particular features of the 2011 edition include: • seven parts: overview and structure, principles of income, deductions and offsets, timing issues, investment and business entities, tax avoidance and administration, and indirect taxes; • clearly structured chapters within those parts grouped under helpful headings; • flowcharts, diagrams and tables, end of chapter practice questions, and case summaries; • an appendix containing all of the up to date and relevant rates; and • the online self-testing component mentor, which provides questions for students of both business and law. Every major aspect of the Australian tax system is covered, with chapters on topics such as goods and services tax, superannuation, offsets, partnerships, capital gains tax, trusts, company tax and tax administration. All chapters have been thoroughly revised. Principles of Taxation Law 2011 is the perfect tool to guide the reader from their initial exposure to the subject to success in taxation law exams. [from publisher's website]

An estimation of crash risks using a log-linear model and the induced exposure technique

Prevention and safety promotion programmes. Traditionally, in-depth investigations of crash risks are conducted using exposure controlled study or case-control methodology. However, these studies need either observational data for control cases or exogenous exposure data like vehicle-kilometres travel, entry flow or product of conflicting flow for a particular traffic location, or a traffic site. These data are not readily available and often require extensive data collection effort on a system-wide basis. Aim: The objective of this research is to propose an alternative methodology to investigate crash risks of a road user group in different circumstances using readily available traffic police crash data. Methods: This study employs a combination of a log-linear model and the quasi-induced exposure technique to estimate crash risks of a road user group. While the log-linear model reveals the significant interactions and thus the prevalence of crashes of a road user group under various sets of traffic, environmental and roadway factors, the quasi-induced exposure technique estimates relative exposure of that road user in the same set of explanatory variables. Therefore, the combination of these two techniques provides relative measures of crash risks under various influences of roadway, environmental and traffic conditions. The proposed methodology has been illustrated using Brisbane motorcycle crash data of five years. Results: Interpretations of results on different combination of interactive factors show that the poor conspicuity of motorcycles is a predominant cause of motorcycle crashes. Inability of other drivers to correctly judge the speed and distance of an oncoming motorcyclist is also evident in right-of-way violation motorcycle crashes at intersections. Discussion and Conclusions: The combination of a log-linear model and the induced exposure technique is a promising methodology and can be applied to better estimate crash risks of other road users. This study also highlights the importance of considering interaction effects to better understand hazardous situations. A further study on the comparison between the proposed methodology and case-control method would be useful.

‘Argue with us!’: audience co-creation through post-performance discussions.

In this article Caroline Heim explores an avenue for the audience's contribution to the theatrical event that has emerged as increasingly important over the past decade: postperformance discussions. With the exception of theatres that actively encourage argument such as the Staatstheater Stuttgart, most extant audience discussions in Western mainstream theatres privilege the voice of the theatre expert. Caroline Heim presents case studies of post-performance discussions held after performances of Anne of the Thousand Days and Who's Afraid of Virginia Woolf? which trialled a new model of audience co-creation. An audience text which informs the theatrical event was created, and a new role, that of audience critic, established in the process.

Long term exposure to asbestos satisfies test for causation

Background In Booth v Amaca Pty Ltd and Amaba Pty Ltd,1 the New South Wales Dust Diseases Tribunal awarded a retired motor mechanic $326 640 in damages for his malignant pleural mesothelioma allegedly caused by exposure to asbestos through working with the brake linings manufactured by the defendants. The evidence before the Tribunal was that the plaintiff had been exposed to asbestos prior to working as a mechanic from home renovations when he was a child and loading a truck as a youth. However, as a mechanic he had been exposed to asbestos in brake linings on which he worked from 1953 to 1983. Curtis DCJ held at [172] that the asbestos from the brake linings ‘materially contributed to [the plaintiff’s] contraction of mesothelioma’. This decision was based upon acceptance that the effect of exposure to asbestos on the development of mesothelioma was cumulative and rejection of theory that a single fibre of asbestos can cause the disease...

Exposure to hot and cold temperatures and ambulance attendances in Brisbane, Australia: A time series study

ABSTRACT Objectives: To investigate the effect of hot and cold temperatures on ambulance attendances. Design: An ecological time series study. Setting and participants: The study was conducted in Brisbane, Australia. We collected information on 783 935 daily ambulance attendances, along with data of associated meteorological variables and air pollutants, for the period of 2000–2007. Outcome measures: The total number of ambulance attendances was examined, along with those related to cardiovascular, respiratory and other non-traumatic conditions. Generalised additive models were used to assess the relationship between daily mean temperature and the number of ambulance attendances. Results: There were statistically significant relationships between mean temperature and ambulance attendances for all categories. Acute heat effects were found with a 1.17% (95% CI: 0.86%, 1.48%) increase in total attendances for 1 °C increase above threshold (0–1 days lag). Cold effects were delayed and longer lasting with a 1.30% (0.87%, 1.73%) increase in total attendances for a 1 °C decrease below the threshold (2–15 days lag). Harvesting was observed following initial acute periods of heat effects, but not for cold effects. Conclusions: This study shows that both hot and cold temperatures led to increases in ambulance attendances for different medical conditions. Our findings support the notion that ambulance attendance records are a valid and timely source of data for use in the development of local weather/health early warning systems.

Exposure to hot and cold temperatures and ambulance attendances in Brisbane, Australia

Objectives: To investigate the effect of hot and cold temperatures on ambulance attendances. Design: An ecological time series study. Setting and participants: The study was conducted in Brisbane, Australia. We collected information on 783 935 daily ambulance attendances, along with data of associated meteorological variables and air pollutants, for the period of 2000–2007. Outcome measures: The total number of ambulance attendances was examined, along with those related to cardiovascular, respiratory and other non-traumatic conditions. Generalised additive models were used to assess the relationship between daily mean temperature and the number of ambulance attendances. Results: There were statistically significant relationships between mean temperature and ambulance attendances for all categories. Acute heat effects were found with a 1.17% (95% CI: 0.86%, 1.48%) increase in total attendances for 1 °C increase above threshold (0–1 days lag). Cold effects were delayed and longer lasting with a 1.30% (0.87%, 1.73%) increase in total attendances for a 1 °C decrease below the threshold (2–15 days lag). Harvesting was observed following initial acute periods of heat effects, but not for cold effects. Conclusions: This study shows that both hot and cold temperatures led to increases in ambulance attendances for different medical conditions. Our findings support the notion that ambulance attendance records are a valid and timely source of data for use in the development of local weather/health early warning systems.