Novel double-sided linear generator for the wave energy conversion

The direct drive point absorber is a robust and efficient system for wave energy harvesting, where the linear generator represents the most complex part of the system. Therefore, its design and optimization are crucial tasks. The tubular shape of a linear generator’s magnetic circuit offers better permanent magnet flux encapsulation and reduction in radial forces on the translator due to its symmetry. A double stator topology can improve the power density of the linear tubular machine. Common designs employ a set of aligned stators on each side of a translator with radially magnetized permanent magnets. Such designs require doubling the amount of permanent magnet material and lead to an increase in the cogging force. The design presented in this thesis utilizes a translator with buried axially magnetized magnets and axially shifted positioning of the two stators such that no additional magnetic material, compared to single side machine, is required. In addition to the conservation of magnetic material, a significant improvement in the cogging force occurs in the two phase topology, while the double sided three phase system produces more power at the cost of a small increase in the cogging force. The analytical and the FEM models of the generator are described and their results compared to the experimental results. In general, the experimental results compare favourably with theoretical predictions. However, the experimentally observed permanent magnet flux leakage in the double sided machine is larger than predicted theoretically, which can be justified by the limitations in the prototype fabrication and resulting deviations from the theoretical analysis.

Greener Alternatives to Selected Organic Oxidation Reactions

The study of green chemistry is dedicated to eliminating or reducing toxic waste. One route to accomplish this goal is to explore alternative reaction conditions and parameters resulting in the development of more benign synthetic routes and reagents. The primary focus of this research is to find optimal reaction conditions for the oxidation of a primary alcohol to an aldehyde. As a case study, the oxidation of benzyl alcohol to benzaldehyde, a common industrial process, was examined. Traditionally carried out using the Jones Reagent, commonly referred to as chromium (IV) oxide or chromium trioxide (CrO3) in sulphuric acid, a great deal of research went into utilizing less toxic reagents, such as MnO2 or KMnO4 supported on a clay base. This research has led to an improvement on these alternatives, using a lithium chloride (LiCl) catalyst in a montmorillonite K10 clay solid phase, together with the oxidizing agent hydrogen peroxide, as even greener alternatives to these traditional oxidizing agents. Experiments were carried out to determine the lifetime of this LiCl/clay system as compared to MnO2 and KMnO4, to investigate its ability to catalyze the oxidation of other aromatic alcohols (such as 4-methoxybenzyl alcohol and diphenylmethanol), and to further improve the system’s adherence to green chemistry principles. Green solvent alternatives were examined by replacing the toluene solvent with dimethylcarbonate (DMC), and reaction conditions were optimized to improve product yield. It was determined that the LiCl/H2O2 system was, in most cases, equally as effective at catalyzing the oxidation of benzyl alcohol to benzaldehyde. Although the catalyst and oxidizing agent eliminated the toxic waste generated from chromium reagents, it offered significant challenges in product isolation, because of an aqueous-organic phase separation.

Development of calix[4]arene-functionalized microcantilever array sensing system for the rapid, sensitive and simultaneous detection of metal ions in aqueous solutions

The work described in this thesis was conducted with the aim of: 1) investigating the binding capabilities of calix[4]arene-functionalized microcantilevers towards specific metal ions and 2) developing a new16-microcantilever array sensing system for the rapid, and simultaneous detection of metal ions in fresh water. Part I of this thesis reports on the use of three new bimodal calix[4]arenes (methoxy, ethoxy and crown) as potential host/guest sensing layers for detecting selected ions in dilute aqueous solutions using single microcantilever experimental system. In this work it was shown that modifying the upper rim of the calix[4]arenes with a thioacetate end group allow calix[4]arenes to self-assemble on Au(111) forming complete highly ordered monolayers. It was also found that incubating the microcantilevers coated with 5 nm of Inconel and 40 nm of Au for 1 h in a 1.0 M solution of calix[4]arene produced the highest sensitivity. Methoxy-functionalized microcantilevers showed a definite preference for Ca²⁺ ions over other cationic guests and were able to detect trace concentration as low as 10⁻¹² M in aqueous solutions. Microcantilevers modified with ethoxy calix[4]arene displayed their highest sensitivity towards Sr²⁺ and to a lesser extent Ca²⁺ ions. Crown calix[4]arene-modified microcantilevers were however found to bind selectively towards Cs⁺ ions. In addition, the counter anion was also found to contribute to the deflection. For example methoxy calix[4]arene-modified microcantilever was found to be more sensitive to CaCl₂ over other water-soluble calcium salts such as Ca(NO₃)₂ , CaBr₂ and CaI₂. These findings suggest that the response of calix[4]arene-modified microcantilevers should be attributed to the target ionic species as a whole instead of only considering the specific cation and/or anion. Part II presents the development of a 16-microcantilever sensor setup. The implementation of this system involved the creation of data analysis software that incorporates data from the motorized actuator and a two-axis photosensitive detector to obtain the deflection signal originating from each individual microcantilever in the array. The system was shown to be capable of simultaneous measurements of multiple microcantilevers with different coatings. A functionalization unit was also developed that allows four microcantilevers in the array to be coated with an individual sensing layer one at the time. Because of the variability of the spring constants of different cantilevers within the array, results presented were quoted in units of surface stress unit in order to compare values between the microcantilevers in the array.