Tunnel engineering – influence of the type and the quantity of measurements in the back analysis of geomechanical parameters

The monitoring data collected during tunnel excavation can be used in inverse analysis procedures in order to identify more realistic geomechanical parameters that can increase the knowledge about the interested formations. These more realistic parameters can be used in real time to adapt the project to the real structure in situ behaviour. However, monitoring plans are normally designed for safety assessment and not especially for the purpose of inverse analysis. In fact, there is a lack of knowledge about what types and quantity of measurements are needed to succeed in identifying the parameters of interest. Also, the optimisation algorithm chosen for the identification procedure may be important for this matter. In this work, this problem is addressed using a theoretical case with which a thorough parametric study was carried out using two optimisation algorithms based on different calculation paradigms, namely a conventional gradient-based algorithm and an evolution strategy algorithm. Calculations were carried for different sets of parameters to identify several combinations of types and amount of monitoring data. The results clearly show the high importance of the available monitoring data and the chosen algorithm for the success rate of the inverse analysis process.

Contribution of the evaluation strategy and the use of hearing protection for the uncertainty associated with occupational exposure to noise

Doctoral Thesis for PhD degree in Industrial and Systems Engineering

Cost efficiency and resistance to chemical attack of a fly ash geopolymeric mortar versus epoxy resin and acrylic paint coatings

This article presents results of an experimental investigation on the resistance to chemical attack (with sulphuric, hydrochloric and nitric acid) of several materials: OPC concrete, high-performance concrete, epoxy resin, acrylic painting and a fly ash-based geopolymeric mortar). Three types of acids with three high concentrations (10, 20 and 30%) were used to simulate long-term degradation. A cost analysis was also performed. The results show that the epoxy resin has the best resistance to chemical attack independently of the acid type and the acid concentration. However, the cost analysis shows that the epoxy resin-based solution is the least cost-efficient solution being 70% above the cost efficiency of the fly ash-based geopolymeric mortar.

Biomaterials for cartilage tissue engineering under mechanical stimulus

Tese de Doutoramento em Ciências (Especialidade de Física)

Lard as a suitable and cheap substrate for microbial lipids production by Yarrowia lipolytica

[Excerpt] Current agricultural and industrial practices have led to the generation of large amounts of various low-value or negative cost crude wastes, which are difficult and economically notattractive to treat and valorize. One important example of waste generation is animal fat, commonly found in tanning process and slaughterhouses. These wastes, in which the lipids are often the main and most problematic components, are not currently used effectively and there are almost no application methods to recover the respective value. (...)

Hierarchical modelling of timber reference properties using probabilistic methods: Maximum Likelihood Method, Bayesian Methods and Probability Networks

In recent decades, an increased interest has been evidenced in the research on multi-scale hierarchical modelling in the field of mechanics, and also in the field of wood products and timber engineering. One of the main motivations for hierar-chical modelling is to understand how properties, composition and structure at lower scale levels may influence and be used to predict the material properties on a macroscopic and structural engineering scale. This chapter presents the applicability of statistic and probabilistic methods, such as the Maximum Likelihood method and Bayesian methods, in the representation of timber’s mechanical properties and its inference accounting to prior information obtained in different importance scales. These methods allow to analyse distinct timber’s reference properties, such as density, bending stiffness and strength, and hierarchically consider information obtained through different non, semi or destructive tests. The basis and fundaments of the methods are described and also recommendations and limitations are discussed. The methods may be used in several contexts, however require an expert’s knowledge to assess the correct statistic fitting and define the correlation arrangement between properties.

Advances in preservation of fruits and vegetables with bioactive coatings

Bioactive compounds are a large group of compounds (antimicrobials, antioxidants, nutrients, etc.), but its use in edible fi lms and coatings for application on fruits and vegetables has been very important because nowadays the consumers demand fruits and vegetables that are fresh, healthy, high quality and easy to prepare. A number of investigations have shown that the use of additives in edible fi lms and coatings improve its functionability and provide compounds for human health. However, it is necessary to continue research that can generate specifi c or tailor-made edible fi lms and coatings for each product with the best characteristics for preservation. In this review we present and analyze the concepts, progress and perspectives in the design and application of edible fi lms and coatings for fruits and vegetables in order to defi ne the challenges and opportunities that this topic of study in the fi eld of science, technology and food engineering.