Semi-analytical finite element analysis of a strip footing on an elastic reinforced soil

A plane strain elastic interaction analysis of a strip footing resting on a reinforced soil bed has been made by using a combined analytical and finite element method (FEM). In this approach the stiffness matrix for the footing has been obtained using the FEM, For the reinforced soil bed (halfplane) the stiffness matrix has been obtained using an analytical solution. For the latter, the reinforced zone has been idealised as (i) an equivalent orthotropic infinite strip (composite approach) and (ii) a multilayered system (discrete approach). In the analysis, the interface between the strip footing and reinforced halfplane has been assumed as (i) frictionless and (ii) fully bonded. The contact pressure distribution and the settlement reduction have been given for different depths of footing and scheme of reinforcement in soil. The load-deformation behaviour of the reinforced soil obtained using the above modelling has been compared with some available analytical and model test results. The equivalent orthotropic approach proposed in this paper is easy to program and is shown to predict the reinforcing effects reasonably well.

Interference of Two Closely Spaced Strip Footings on Sand Using Model Tests

By using small scale model tests, the interference effect on the ultimate bearing capacity of two closely spaced strip footings, placed on the surface of dry sand, was investigated. At any time, the footings were assumed to (1) carry exactly the same magnitude of load; and (2) settle to the same extent. No tilt of the footing was allowed. The effect of clear spacing (s) between two footings was explicitly studied. An interference of footings leads to a significant increase in their bearing capacity; the interference effect becomes even more substantial with an increase in the relative density of sand. The bearing capacity attains a peak magnitude at a certain (critical) spacing between two footings. The experimental observations presented in this technical note were similar to those given by different available theories. However, in a quantitative sense, the difference between the experiments and theories was seen to be still significant and it emphasizes the need of doing a further rigorous analysis in which the effect of stress level on the shear strength parameters of soil mass can be incorporated properly.

Silicon Tetrachloride/Sodium Iodide as a Convenient and Highly Regioselective Ether Cleaving Reagent

Abstract is not available.

Strip-loaded waveguide using an underlay

We describe how an ion-exchange waveguide was used as a strip-loading region for a planar polymer waveguide. The loading strip forms an underlay that is well preserved in the substrate. Some branching-channel waveguides were formed by this method, and wall losses were measured. The result shows that the wall losses decrease as a result of strip loading.

Pyridinium poly(hydrogen fluoride). A versatile fluorinating reagent preparation and characterization of nonmetal and metal complex fluoro salts

Abstract is not available.

New reagents 3: aluminium iodide - a highly regioselective ether-cleaving reagent with novel cleavage pattern

AlI3 is an easily accessible and versatile ether-cleaving reagent.

Synthesis of Thioesters from Carboxylic Acids via Acyloxyphosphonium Intermediates with Benzyltriethylammonium Tetrathiomolybdate as the Sulfur Transfer Reagent

An efficient protocol is reported for the synthesis of thioesters from carboxylic acids with use of acyloxy phosphonium salts as intermediates and benzyltriethylammonium tetrathiomolybdate as the sulfur transfer reagent.

Pyridinium poly(hydrogen fluoride)- a reagent for the preparation of hexafluorophosphates

Pyridinium poly(hydrogen fluoride) has been found to be an efficient and versatile reagent for the preparation of hexafluorophosphates. Pyridinium hexafluorophosphate has been prepared by the reaction between phosphorus (V) halides (POCl3, POBr3, PSCl3, PCl5, PBr5) and pyridinium poly(hydrogen fluoride). This in turn is used to prepare the hexafluorophosphates of ammonium, sodium, potassium, rubidium and cesium in good yield and high purity.

Hydrazinium thiocyanate as a reagent for determination of copper

Hydrazinium thiocyanate, N2H5SCN, has been used for the determination of copper in copper salts. The reagent reduces the copper ions to the cuprous state and precipitates cuprous thiocyanate Cu2(SCN)2, quantitatively.

Synthesis of Thioesters by Simultaneous Activation of Carboxylic Acids and Alcohols Using PPh3/NBS with Benzyltriethylammonium Tetrathiomolybdate as the Sulfur Transfer Reagent

A new and simple route for the synthesis of thioesters starting from carboxylic acids and alcohols is reported by using tetrathiomolybdate as the key sulfur transfer reagent. Triphenylphosphane and N-bromosuccinimide were used for the activation of the carboxylic acid and alcohol in the same pot followed by the transfer of sulfur from tetrathiomolybdate. Thioesters were obtained in good to moderate yields. Primary alcohols show excellent reactivity and gave good yields of the corresponding thioesters, whereas secondary alcohols gave moderate yields and tertiary alcohols were very less reactive and gave poor yields of the corresponding thioesters.

Folin-Ciocalteu reagent for the estimation of siderochromes

1. A simple method has been devised for the estimation of siderochromes based on their reaction with Folin-Ciocalteu reagent to give a blue complex under alkaline conditions. 2. The applicability of the method to biological systems has been tested with N. crassa and concentrations in the ranges 5–50 μg and 1–10 μg can be accurately estimated with an over-all recovery of 95%.

Potassium phosphate as a reagent for the gravimetric estimation of lithium

Previous attempts for the quantitative estimation of lithium as orthophosphate, employing an alkali metal phosphate, have not been successful. A method, is described for the estimation of lithium as trilithium phosphate from 60% ethyl alcohol solution at 65° to 70° C., employing potassium phosphate reagent, at pH 9.5. The method is applicable in the presence of varying amounts of sodium and/or potassium cations and chloride, sulfate, nitrate, and phosphate anions.