Enhancement of nonvolatile polarization and pyroelectric sensitivity in lithium tantalate (LT)/poly(vinylidene fluoride) (PVDF) nanocomposite

We report the ferroelectric and pyroelectric properties of the composite films of lithium tantalate (LT) nanoparticle in poly(vinylidene fluoride) PVDF matrix at different volume fractions of LT (f(LT) = 0.047, 0.09 and 0.17). For an applied electric field of 150 kV cm(-1) the nonvolatile polarization of the composite was observed to increase from 0.014 mu C cm(-2) at f(LT) = 0 to 2.06 mu C cm(-2) at f(LT) = 0.17. For f(LT) = 0.17, the composite films exhibit a saturated ferroelectric hysteresis loop with a remanent polarization (2P(r) = 4.13 mu C cm(-2)). Compared with pure poled PVDF the composite films also showed a factor of about five enhancement in the pyroelectric coefficient at f(LT) = 0.17. When used in energy detection mode the pyroelectric voltage sensitivity of the composite films was found to increase from 3.93 to 18.5 VJ(-1) with an increase in f(LT) from 0.0 to 0.17.

Thermodynamics of cobalt-manganese alloys using fluoride and oxide electrolytes

Abstract is not available.

Re-use of fluoride contaminated bone char sludge in concrete

Managing sludge generated by treating groundwater contaminated with geogenic contaminants (fluoride, arsenic, and iron) is a major issue in developing nations. Their re-use in civil engineering applications is a possible pathway for reducing the impact on the geo-environment. This paper examines the re-use of one such sludge material, namely, fluoride contaminated bone char sludge, as partial replacement for fine aggregate (river-sand) in the manufacture of dense concrete specimens. Bone char sludge is being produced by defluoridation of contaminated groundwater in Nalagonda District, Andhra Pradesh, India. The impact of admixing 1.5-9% sludge contents on the compression strength and fluoride leaching potential of the sludge admixed concrete (SAC) specimens are examined. The compression strengths of the SAC specimensa re examined with respect to strength criteria for manufacture of dense, load-bearing concrete blocks. The fluoride release potential of the SAC specimens is examined with respect to standards specific to disposal of treated leachate into inland surface water.

Pyridinium poly(hydrogen fluoride). A versatile fluorinating reagent preparation and characterization of nonmetal and metal complex fluoro salts

Abstract is not available.

Studies on the reactions of thionyl fluoride

Thionyl fluoride undergoes quantitative oxidation with chloramine-T and reduction with lithium aluminium hydride and sodium borohydride. At elevated temperatures, (>150°C) it reacts with metals such as copper, silver, zinc and lead forming the corresponding metal sulphides, fluorides and sulphur dioxide. With the respective metal oxides, the metal fluorides and sulphur dioxide are formed.

Reaction of thiophosphoryl fluoride with sulphur trioxide

Thiophosphoryl fluoride is observed to undergo a facile reaction with sulphur trioxide forming phosphoryl fluoride, sulphur dioxide and elemental sulphur in quantitative yields. In the presence of excess of sulphur trioxide, however, the elemental sulphur released combines with it to form sulphur sesquioxide which subsequently decomposes and gives off sulphur dioxide. Similar observations are made with oleum.

Reactions of sulphuryl fluoride, sulphuryl chlorofluoride and sulphuryl chloride with amines

The reactions of sulphuryl fluoride, sulphuryl chlorofluoride and sulphuryl chloride with the amines tert-butylamine, benzylamine, piperidine, pyridine and quinoline have been investigated. The primary and secondary amines react with the elimination of hydrogen halides and formation of S---N bonds whereas tertiary amines form 1:2 adducts.

Influence of Lithium Fluoride on the Burning Rate of AP-Polyester Propellant

THE addition of catalysts normally serves the purpose of imparting a desired burning rate change in a composite propellant. These may either retard or enhance the burning rate. Some often quoted catalysts are oxides, chromites and chromates of metals. A lot of work has been done on rinding the effect of the addition of some of these catalysts on the burning rate; however, none seems to have appeared on the influence of lithium fluoride (LiF). Only qualitative reduction in the burning rate of composite propellants with the addition of LiF was reported by Williams et al.1 Dickinson and Jackson2 reported a slight decrease in the specific impulse of composite propellant with the addition of LiF; however, they made no mention of the effect of its addition on the burning rate. We have studied the effect of the addition of varying amounts of LiF on the burning rate of Ammonium Perchlorate (AP)-Polyester propellant.

Investigations on the preparation, oxidation and reduction reactions of thiophosphoryl fluoride

Pure thiophosphoryl fluoride has been prepared by the fluorination of thiophosphoryl chloride by sodium fluoride in acetonitrile medium. Oxidation of this phosphoryl fluoride by acidified chloramine-T ruptures the phosphorus-sulphur bond and oxidises the sulphur present to the hexavalent state. Anhydrous hydrogen iodide reduces the sulphur to hydrogen sulphide and phosphorus to the trivalent state.

Thiophosphoryl fluoride and phosphoryl fluoride as initiators for the polymerisation of tetrahydrofuran

Thiophosphoryl fluoride and phosphoryl fluoride have been found to initiate the polymerisation of tetrahydrofuran. The living polymer formed has a high molecular weight of the order of a million and the density is found to be between 0.98 - 1.02 g/cc. A cationic mechanism for the polymerisation has been proposed.

A New Method for the Preparation of Sulphuryl Chloro Fluoride

It has been observed that a suspension of sodium fluoride in boiling acetonitrile could be used for the preparation of fluorine compounds such as silicon tetrafluoride [1], thiophosphoryl fluoride [2], sulphur tetrafluoride [3,4], and fluorocyclophosphazenes [5]. This method, when adopted for the fluorination of sulphuryl chloride [6], it is observed that a mixture of sulphuryl fluoride and sulphuryl chloro fluoride is obtained. On the other hand, when lead fluoride is substituted for sodium fluoride, pure sulphuryl chloro fluoride is evolved. Based on this observation, a new method has been standardised for the preparation of a pure sample of sulphuryl chlorofluoride by fluorinating sulphuryl chloride by lead fluoride in acetonitrile medium.

Pyridinium poly(hydrogen fluoride)- a reagent for the preparation of hexafluorophosphates

Pyridinium poly(hydrogen fluoride) has been found to be an efficient and versatile reagent for the preparation of hexafluorophosphates. Pyridinium hexafluorophosphate has been prepared by the reaction between phosphorus (V) halides (POCl3, POBr3, PSCl3, PCl5, PBr5) and pyridinium poly(hydrogen fluoride). This in turn is used to prepare the hexafluorophosphates of ammonium, sodium, potassium, rubidium and cesium in good yield and high purity.

Reaction of thiophosphoryl fluoride with metals and metal oxides

Abstract is not available.

Hydrolysis of thiophosphoryl fluoride

The hydrolysis of thiophosphoryl fluoride has been studied both in acid and alkaline medium. The products are phosphate, fluoride and varying amounts of sulphide, sulphite, thiosulphate and elemental sulphur depending on experimental conditions. The probable mode of formation of the different sulphur species has been explained on the basis of sulphur in a higher oxidation state in the thiophosphoryl fluoride molecule.