The high temperature mechanical characteristics of superplastic 3 mol% yttria stabilized zirconia

A detailed study was undertaken to characterize the deformation behavior of a superplastic 3 mol% yttria-stabilized tetragonal zirconia (3YTZ) over a wide range of strain rates, temperatures and grain sizes. The experimental data were analyzed in terms of the following equation for high temperature deformation: Image Full-size image ∞ σn d−pexp(−Q/RT), where Image Full-size image is the strain rate, σ is the flow stress, d is the grain size, Q is the activation energy, R is the gas constant, T is the absolute temperature, and n and p are constants termed the stress exponent and the inverse grain size exponent, respectively. The experimental data over a wide range of stresses revealed a transition in stress exponent. Deformation in the low and high stress regions was associated with n not, vert, similar 3 and p not, vert, similar 1, and n not, vert, similar 2 and p not, vert, similar 3, respectively. The transition stress between the two regions decreased with increasing grain size. The activation energy was similar for both regions with a value of not, vert, similar 550 kJ mol−1. Microstructural measurements revealed that grains remained essentially equiaxed after the accumulation of large strains, and very limited concurrent grain growths occurred in most experiments. Assessment of possible rate controlling creep mechanisms and comparison with previous studied indicate that in the n not, vert, similar 2 region, deformation occurs by a grain boundary sliding process whose rate is independent of impurity content. Deformation in the n not, vert, similar 3 region is controlled by an interface reaction that is highly sensitive to impurity content. It is concluded that an increase in impurity content increases yttrium segregation to grain boundaries, which enhances the rate of the interface reaction, thereby decreasing the apparent transition stress between the n not, vert, similar 2 and n not, vert, similar 3 regions. This unified approach incorporating two sequential mechanisms can rationalize many of the apparently dissimilar results that have been reported previously for deformation of 3YTZ.

Polarized Ethylenes: Structure of 2-Benzoyl-3-dimethylamino-3-methylthlo-2-propenenitrile

C13H14N2OS, M r = 246, is monoclinic, P21/c, with a = 7.214(1), b = 8.935(5), c = 20.243 (6) A, fl =99.42 (2) °, V = 1304.83 ,~3, Z = 4, D m = 1.23, D x =1.25 Mg m -3, p(Mo Ka, 2 = 0.7107 A) = 0.232 mm -~,F(000) = 520. The structure was solved by direct methods and refined to an R value of 0.042 using 1127 intensity measurements. The C=C and C-N bond distances differ considerably from their normal values. An appreciable rotation [38.3(4) °] about the C=C bond is observed, the bond length being 1.414(5)A.This is due to the combination of push-pull and steric effects.

Zeeman effect of chlorine nuclear quadrupole resonance and hydrogen bonding in 2,6-, 2,5- and 3,5-dichlorophenols

The Zeeman effect of chlorine nuclear quadrupole resonance in polycrystalline samples of 2,6-, 2,5 and 3,5-dichlorophenol has been investigated at room temperature in order to study the effect of hydrogen bonding on the electric field gradient asymmetry parameter n. While the two n.q.r. lines in 3,5-dichlorophenol gave an asymmetry parameter of 10%, those in 2,6- and 2,5-dichlorophenol gave different values of n for the two chlorines. The chlorine atom which is ortho to the OH group and involved in hydrogen bonding (i.e., corresponding to the low frequency line) gave an asymmetry parameter of 0.21 in 2,6-dichlorophenol and 0.17 in 2,5-dichlorophenol while the other chlorine (i.e., corresponding to the high frequency line) gave a lower value of 0.12 in 2,6-dichlorophenol and 0.11 in 2,5-dichlorophenol. These values of n are discussed in terms of hydrogen bonding and bond parameters.

Non-bonded interactions in 2,2,4,4-tetramethyl-1,3-cyclobutanedithione and 2,2,4,4-tetramethyl-3-thio-1,3-cyclobutanedione

Electronic absorption and emission spectra as well as He(I) photoelectron spectra of 2,2,4,4-tetramethyl-,3-cyclobutanedithione and 2,2,4,4-tetramethyl-1-3-thio-1,3-cyclobutanedione have been interpreted on the basis of molecular orbital calculations. The results show that the non-bonded orbital of the dithione is split owing to through-bond interaction, the magnitude of splitting being 0.4 eV. The π* orbital of the dithione appears to be split by about 0.2 eV. Electronic absorption spectra show evidence for the existence of four n—π* transitions, arising out of the splitting of the orbitals referred to above, just as in the case of 2,2,4,4-tetramethyl-1,3-cyclobutanedione. Electronic and photoelectron spectra of the thio-dione show evidence for weak interaction between the C=S and C&.zdbnd;O groups, probably via π* orbitals. Infrared spectra of both the dithione and the thio-dione are consistent with the planar cyclobutane ring; the ring-puckering frequency responsible for non-bonded interactions is around 67 cm−1 in both the dithione and the thio-dione, the value not being very different from that in the dione. The 1,3-transannular distance is also similar in the three molecules.

Structure of ethyl 1,2,2-tricyano 3-(4-nitrophenyl)-cyclopropane-1-carboxylate

C15HIoN404, monoclinic, P2~/c, a = 10.694(8), b = 11.743 (8), c - 12.658 (8) A, fl = 113.10 (7) °, V = 1462.1 A 3, Z = 4, O m = 1 "38, O c = 1.408 g cm -3, t,t(MoKa, ~, = 0.7107 ]~) = 0.99 cm -i, F(000) = 640. The structure was solved by direct methods and refined to an R value of 0.054 using 1398 intensity measurements. The relative magnitudes of interaction of the substituents and the extent to which a ring can accommodate interactions with substituents are discussed.

TlCaBa2Cu2O7: The 1122 (90 K) superconductor in the new Tl(Ca,Ba)n+1CunO2n+3 seriesstar, open

The 1122 (n=2) member of the Tl(Ca,Ba)n+1CunO2n+3 series containing a single Tl-O layer is shown to be associated with a Tc of 90 K. This value of Tc is significantly lower than that of the 2122 phase (Tcnot, vert, similar110 K) with two Tl-O layers.

Reinvestigation of the structure of Feist's acid 3-methylene-trans-1,2-cyclopropanedicarboxylic acid

C6H604, Mr = 142, triclinic, P[, a = 4.842(1), b = 7.607(1), c = 9.168 (3) A, ~ = 98.41(2), fl = 99.89(2), y = 77.74(1) ° , V = 320.9/k 3, Z = 2, Dm= 1.45 (flotation), D x = 1.470 g cm -3, p(Mo Ktt, 2 = 0.7107 A) = 0.63 cm -~, F(000) = 148. The structure was solved by direct methods and refined to an R value of 0.038 for 723 intensity measurements. The geometrical changes in the cyclopropane ring are discussed in the light of substituent effects. In the crystal structure the carboxylic groups are disordered.

Is 3'-nucleotide rigid?

Conformational analysis of nucleic acids and polynucleotides is far more complex than that of proteins and polypeptides, due to five single bond rotations in addition to the sugar puckerings in the monomer. Sundaralingam1 proposed the concept of the 'rigid' nucleotides from analysis of crystal structure data, with the flexibility allowed only about the phosphodiester bonds. However, the crystal structure of deoxyguanosine-5'−phosphate2,3 indicates at gt conformation about the C-4'−C-5' bond against gg in a conformationally rigid nudeotide1. Jack et al. 4 considered the flexibility of nucleotides in tRNA about the C-4'−C-5' bond, thereby introducing the concept of 'non-rigid' ribonucleotides. Conformational flexibility of the f uranose ring in DNA and RNA and their energetics using classical and quantum chemical methods have been reported5−8. We have examined the flexibility of 3'-nucleotides. alpha, the most important of the conformational parameters defining the 3'-end of a nucleotide unit9, has a value in the range 195°−270° in all the 3'-nucleotides, dinucleoside monophosphates and higher oligomers which have been surveyed. A survey of the proposed structures of polyribonudeotides10,11 also shows the values of a to be greater than 200°. However, the structures proposed for B-DNA by Arnott and Hukins12,13 and D-DNA by Arnott et al. 14 have values of alpha of 155° and 141° respectively, much lower than the lowest observed value. The structure for B-DNA has two strong, short contacts (C-2'...OP-1 = 2.64 Å and HC-2"...OP-1 = 1.79 Å) which lead to an energetically unfavourable conformation. Hence, it is of interest to investigate whether, by allowing flexibility to the sugar moiety in the nucleotide unit, it is possible to make the structure energetically favourable. Here, conformational energy calculations were carried out to determine the range of alpha which would give rise to energetically favoured conformations with different sugar puckerings. Our analysis has shown that the theoretically obtained range is nearly the same as the preferred range in crystals, indicating the flexibility of the 3'-nucleotides.

The structure of 3-(2-methoxyphenyl)-1,1,2,2-cyclopropanetetracarbonitrile

Crystals of C I4HsN40 are monoclinic, space group P21, Unit-cell constants are a = 13.241(4), b = 7.446 (2), c = 6.436 (2)/A, B= 93.23 (2) °. V= 633.5 /A3, Z = 2, Dob s = 1.30 (flotation), Dealt = 1.300 Mg m -3 and #(Cu Ka) = 0.72 mm -1. The structure, solved by direct methods, has been refined to an R value of 3.5% using 1245 intensity measurements. The combined effect of electron-withdrawing and –donating substituents on the geometry of the cyclopropane ring is discussed.

Crystallization Kinetics and Electrical Relaxation of BaO-0.5Li(2)O-4.5B(2)O(3) Glasses

Transparent glasses in the composition BaO-0.5Li(2)O-4.5B(2)O(3) (BLBO) were fabricated via the conventional melt-quenching technique. X-ray powder diffraction combined with differential scanning calorimetric (DSC) studies carried out on the as-quenched samples confirmed their amorphous and glassy nature, respectively. The crystallization behavior of these glasses has been studied by isothermal and nonisothermal methods using DSC. Crystallization kinetic parameters were evaluated from the Johnson-Mehl-Avrami equation. The value of the Avrami exponent (n) was found to be 3.6 +/- 0.1, suggesting that the process involves three-dimensional bulk crystallization. The average value of activation energy associated with the crystallization of BLBO glasses was 317 +/- 10 kJ/mol. Transparent glass-ceramics were fabricated by controlled heat-treatment of the as-quenched glasses at 845 K/40 min. The dielectric constants for BLBO glasses and glass-ceramics in the 100 Hz-10 MHz frequency range were measured as a function of the temperature (300-925 K). The electrical relaxation and dc conductivity characteristics were rationalized using electric modulus formalism. The imaginary part of the electric modulus spectra was modeled using an approximate solution of the Kohlrausch-Williams-Watts relation. The temperature-dependent behavior of stretched exponent (beta) was discussed for the as-quenched and heat-treated BLBO glasses.

Structure of ethyl 1,2,2-tricyano-3-(4-nitrophenyl)-cyclopropane-1-carboxylate

C15HIoN404, monoclinic, P2~/c, a = 10.694(8), b = 11.743 (8), c - 12.658 (8) A, fl = 113.10 (7) °, V = 1462.1 A 3, Z = 4, O m = 1 "38, O c = 1.408 g cm -3, t,t(MoKa, ~, = 0.7107 ]~) = 0.99 cm -i, F(000) = 640. The structure was solved by direct methods and refined to an R value of 0.054 using 1398 intensity measurements. The relative magnitudes of interaction of the substituents and the extent to which a ring can accommodate interactions with substituents are discussed.

Purification and properties of protocatechuate-3,4-dioxygenase from Tecoma stans L

Protocatechuate-3,4-dioxygenase from the leaves of Tecoma stans was purified to near homogeneity and some of its properties studied. It was optimally active at pH 5.2 and at 40°C. Its molecular weight of approx. 150 000 was determined by gel filtration on a Sephadex G-150 column. The Km value for protocatechuate was found to be 330 μM and for ferrous sulfate, 40 μM. The enzyme was highly specific for protocatechuate and did not attack any of the substrate analogues. None of the substrate analogues tested inhibited the enzyme activity. Sulfhydryl reagents inhibited the enzyme activity which could be partially reversed by sulfhydryl compounds. The dioxygenase activity was not associated with polyphenol oxidase activity.

A comparative molecular dynamics study of diffusion of n-decane and 3-methyl pentane in Y zeolite

Molecular dynamics simulations are reported on the structure and dynamics of n-decane and 3-methylpentane in zeolite NaY. We have calculated several properties such as the center of mass-center of mass rdf, the end-end distance distribution, bond angle distribution and dihedral angle distribution. We have also analysed trajectory to obtain diffusivity and velocity autocorrelation function (VACF). Surprisingly, the diffusivity of 3-methylpentane which is having larger cross-section perpendicular to the long molecular axis is higher than n-decane at 300 K. Activation energies have been obtained from simulations performed at 200 K, 300 K, 350 K, 400 K and 450 K in the NVE ensemble. These results can be understood in terms of the previously known levitation effect. Arrhenious plot has higher value of slope for n-decane (5 center dot 9 kJ/mol) than 3-methylpentane (3 center dot 7 kJ/mol) in agreement with the prediction of levitation effect.

Sensitivity of Eigen Value to Damage and Its Identification

The reduction in natural frequencies,however small, of a civil engineering structure, is the first and the easiest method of estimating its impending damage. As a first level screening for health-monitoring, information on the frequency reduction of a few fundamentalmodes can be used to estimate the positions and the magnitude of damage in a smeared fashion. The paper presents the Eigen value sensitivity equations, derived from first-order perturbation technique, for typical infra-structural systems like a simply supported bridge girder, modelled as a beam, an endbearing pile, modelled as an axial rod and a simply supported plate as a continuum dynamic system. A discrete structure, like a building frame is solved for damage using Eigen-sensitivity derived by a computationalmodel. Lastly, neural network based damage identification is also demonstrated for a simply supported bridge beam, where the known-pairs of damage-frequency vector is used to train a neural network. The performance of these methods under the influence of measurement error is outlined. It is hoped that the developed method could be integrated in a typical infra-structural management program, such that magnitudes of damage and their positions can be obtained using acquired natural frequencies, synthesized from the excited/ambient vibration signatures.

Boundary value problems for third-order nonlinear ordinary differential equations

In this paper, we describe how to analyze boundary value problems for third-order nonlinear ordinary differential equations over an infinite interval. Several physical problems of interest are governed by such systems. The seminumerical schemes described here offer some advantages over solutions obtained by using traditional methods such as finite differences, shooting method, etc. These techniques also reveal the analytic structure of the solution function. For illustrative purposes, several physical problems, mainly drawn from fluid mechanics, are considered; they clearly demonstrate the efficiency of the techniques presented here.