Expansivity of liquid (cyclohexane + acetic anhydride) near its critical solution point

A simple volume dilatometer is described for the precise measurements of volume changes as a function of temperature in liquid mixtures. The expansivity of (cyclohexane + acetic anhydride) in the critical region was measured. The critical solution temperature Tc was approached to within 9 mK. For T > (Tc + 0.3 K), the results results follow both a logarithmic and a power-law behaviour with an exponent ≈ 1/8. But for T < (Tc + 0.3 K), the results seem to be affected possibly by gravity or temperature gradients. In this region, the expected expansivity anomaly is rounded off to a cusp. The expansivity shows a reduced anomaly for off-critical compositions. A discussion of the local extremum and a correlation between negative expansivity and the resistivity anomaly are also given.

Coexistence curve of acetonitrile and cyclohexane liquid system

The paper reports a detailed determination of the coexistence curve for the binary liquid system acetonitrile+cyclohexane, which have very closely matched densities and the data points get affected by gravity only for t=(Tc−T)/ Tc[approximately-equal-to]10−6. About 100 samples were measured over the range 10−6

On the conformation of cyclohexane-1,4-dione and its derivatives—I : Infrared and raman spectra of cyclohexane 1,4-dione and infrared spectrum of its octadeutero analogue

Raman spectra of cyclohexane 1,4-dione (I), in chloroform, benzene and water solutions have been recorded. Temperature effect on the spectrum has been studied. The IR spectra of I and its octadeutero analogue in the solid state have also been studied. The spectra have been found on the basis of selection rules applicable for Raman and IR spectra, to be consistent with a single conformer of C2 symmetry. Plausible causes of conformational preference have been discussed.

Electrical and Dielectric Behaviour at the Critical Point of Binary Liquids: Acetonitrile + Cyclohexane

The electrical capacitance and resistance of the binary liquid mixture cyclohexane + acetonitrile are measured in the one phase and two phase regions at spot frequencies between 5 kHz and 100 kHz. This sample has a very low gravity affected (∼0.6 mK) region. In one phase region the capacitance data show a sharp, ∼0.7% increase above background within 0.5 degrees of Tc whereas the resistance has a smooth increase of ∼1.5% above background in a (T−Tc) range of 4 degrees. Two phase values of capacitance and resistance from the coexisting phases are used to determine the critical parameters Tc (critical temperature), Rc (resistance at Tc) and Cc (capacitance at Tc). A precise knowledge of these parameters reduces the uncertainty on the critical exponent 0 for C and R. The one phase capacitance data fit to an (1 - α) exponent in a limited temperature range of 0.2 degrees. Resistance data strongly support an (1 - α) exponent over the entire 5 degree range.

Amino acid-lanthanide interactions, Part 2. The X-ray crystal structures of lanthanide and calcium complexes of 1-amino-cyclohexane-1-carboxylic acid (Acc6)

The structures of [Nd-2(Acc(6))(H2O)(6)](ClO4)(6) .(H2O)(6) (1) [Er-2(Acc(6))(4)(H2O)(8)](ClO4)(6) .(H2O)(11) (2) and [Ca-5(Acc(6))(12)(H2O)(6)](ClO4)(10).(H2O)(4) (3) (Acc(6) = 1-aminocyclohexane-1-carboxylic acid) have been determined by X-ray crystallography. The lanthanide complexes 1 and 2 are dimeric in which two lanthanide cations are bridged by four carboxylato groups of Acc(6) molecules. In addition, the neodymium complex (1) features the unidentate coordination of the carboxyl group of an Acc(6) molecule in place of a water molecule in the erbium complex (2). The coordination number in both 1 and 2 is eight. The calcium Acc(6) complex (3) is polymeric; three different calcium environments are observed in the asymmetric unit. Two calcium ions are hexa-coordinated and one is hepta-coordinated. Considerable differences are observed between the solid state structures of Ln(III) and Ca-II complexes of Acc(6

Synthesis, characterization and photocatalytic activity of MxCe1-xVO4 (M = Li, Ca and Fe)

Non-stoichiometric substituted cerium vanadates, MxCe1-xVO4 (M = Li, Ca and Fe), were synthesized by solid-state reactions. The crystal structure was analyzed by powder X-ray diffraction and it exhibits a tetragonal zircon Structure, crystallizing in the space group I4(1)/amd with a = 7.3733(4) and c = 6.4909(4) angstrom and Z = 4. Particle sizes were in the range of 600-800 nm, as observed by scanning electron microscopy. The thermal analysis of the compounds showed phase stability up to 1100 degrees C. The UV diffuse reflectance spectra indicated that the compounds have band gaps in the range of 2.6-2.9 eV. The photocatalytic activity of these Compounds was investigated for the first time for the degradation of different dyes, and organics, the oxidation of cyclohexane and the hydroxylation of benzene. The degradation of dyes was modeled using the Langmuir-Hinshelwood kinetics, while the oxidation of cyclohexane and hydroxylation of benzene were modeled using a free radical mechanism and a series reaction mechanism, respectively.

Metabolism of alpha-terpineol by Pseudomonas incognita

Details of the metabolism of alpha-terpineol by Pseudomonas incognita are presented. Degradation of alpha-terpineol by this organism resulted in the formation of a number of acidic and neutral metabolites. Among the acidic metabolites, beta-isopropyl pimelic acid, 1-hydroxy-4-isopropenyl-cyclohexane-1-carboxylic acid, 8-hydroxycumic acid, oleuropeic acid, cumic acid, and p-isopropenyl benzoic acid have been identified. Neutral metabolites identified were limonene, p-cymene-8-ol, 2-hydroxycineole, and uroterpenol. Cell-free extracts prepared from alpha-terpineol adapted cells were shown to convert alpha-terpineol, p-cymene-8-ol, and limonene to oleuropeic acid, 8-hydroxycumic acid, and perillic acid, respectively, in the presence of NADH. The same cell-free extract contained NAD+ -specific dehydrogenase(s) which converted oleuropyl alcohol, p-cymene-7,8-diol, and perillyl alcohol to their corresponding 7-carboxy acids. On the basis of various metabolites isolated from the culture medium, together with the supporting evidence obtained from enzymatic and growth studies, it appears that P. incognita degrades alpha-terpineol by at least three different routes. While one of the pathways seems to operate via oleuropeic acid, a second may be initiated through the aromatization of alpha-terpineol. The third pathway may involve the formation of limonene from alpha-terpineol and its further metabolism.

Photolysis of the dithiolactone 4-isopropylidene-3,3-dimethyl-1-thietan-2-thione; a Norrish type I reaction

The dithiolactone (1) upon excitation gives the dithione (2) in cyclohexane and other aprotic solvents and a 1 : 1 adduct in hydroxylic solvents from an n* excited singlet state via an -cleavage process.

Conformational effects in the hydrogenation of hemimellitic and cyclohex-1-ene-1,2,3-tricarboxylic acids

The three possible isomers of cyclohexane-1,2,3-tricarboxylic acid were synthesised and separated in order to study the regiospecificity and stereoselectivity of the α-C alkylation of their trimethyl esters. No definitive conclusions could be reached on this aspect for reasons which became apparent in the course of the work. However, the three independent methods adopted for the synthesis of the isomeric tricarboxylic acids have given dramatically different isomer compositions. The reasons are explored in this paper.

An XPS study of the surface oxidation states of metals in some oxide catalysts

Calcined samples of chromia supported on Al2O3, ZnO, or SnO2 show both Cr(VI) and Cr(III) on the surface, Cr(VI) being preponderant in the case of Al2O3-supported catalysts. The proportion of Cr(VI) decreases with increase in Cr content of the calcined catalysts. Reduction of the supported chromia catalysts in H2 at 720 K for 1 hr gives rise to Cr(III) and Cr(V). On carrying out the dehydrogenation of cyclohexane on the chromia catalysts a higher proportion of Cr(V) is found than after treatment with hydrogen. Vanadia supported on Al2O3 or MoO3 shows significant proportion of V(IV) on carrying out the oxidation of toluene on the catalysts. Calcined MoO3 (10%)/Al2O3 shows only Mo(VI) on the surface at 300 K, but on heating to 670 K in vacuum shows the presence of a considerable proportion of Mo(V) which on cooling disproportionates to Mo(IV) and Mo(VI). Mo(V) is noticed on surfaces of this catalyst on reduction with hydrogen as also on carrying out dehydrogenation of cyclohexane. While Bi2MoO6 shows only Mo(VI) on the surface at 300 K, heating it to 670 K in vacuum changes it entirely to Mo(V) which then gives rise to Mo(IV) and Mo(VI) on cooling.

Photocatalytic activity of Ag-substituted and impregnated nano-TiO2

Ag-substituted (Ag sub) and Ag-impregnated (Ag imp), anatase phase nano-TiO2 have been synthesized by solution combustion technique and reduction technique, respectively. The catalysts were characterized extensively by powder XRD, TEM, XPS, FT-Raman, UV absorption, FT-IR, TGA, photoluminescence, BET surface area and isoelectric pH measurements. These catalysts were used for the photodegradation of dyes and for the selective photooxidation of cyclohexane to cyclohexanone. The photoactivities of the combustion-synthesized catalysts were compared with those of commercial Degussa P 25 (DP 25) TiO2, and Ag-impregnated DP 25 (Ag DP). For the photocatalytic degradation of dyes, unsubstituted combustion-synthesized TiO2 (CS TiO2) exhibited the highest activity, followed by 1% Ag imp and 1% Ag sub. For the photoconversion of cyclohexane, the total conversion of cyclohexane and the selectivity of cyclohexanone followed the order: 1% Ag sub > DP 25 > CS TiO2 > 1% Ag imp > 1% Ag DP. The kinetics of the photodegradation of dyes and of the photooxidation of cyclohexane were modeled using Langmuir–Hinshelwood rate equation and a free radical mechanism, respectively, and the rate coefficients were determined. The difference in activity values of the catalysts observed for these two reactions and the detailed characterization of these catalysts are described in this study.

Conformationally Restricted Nucleocyclitols: a Study into their Conformational Preferences and Supramolecular Architecture in the Solid State

With the intent of probing the feasibility of employing annulation as a tactic to engender axial rich conformations in nucleoside analogues, two adenine-derived, ``conformationally restricted'' nucleocylitols, 9 and 10, have been conceptualized as representatives of a hitherto unexplored class of nucleic acid base-cyclitol hybrids. A general synthetic strategy, with an inherent scope for diversification, allowed rapid functionalization of indane and tetralin to furnish 9 and 10 respectively in fair yield. Single-crystal X-ray diffraction analysis revealed that the two nucleocyclitols under study, though homologous, present completely dissimilar modes of molecular packing, marked, in particular, by the nature of involvement of the adenynyl NH2 group in the supramolecular assembly. In addition, the crystal structures of 9 and 10 also exhibit two different conformations of the functionalized cyclohexane ring. Thus, while the six-membered carbocycle in cyclopenta-annulated 9 exists in the expected chair (C) conformation that in cyclohexaannulated 10, which crystallizes as a dihydrate, shows an unusual twist-boat (TB) conformation. From a close analysis of the (HNMR)-H-1 spectroscopic data recorded for 9 and 10 in CD3OD, it was possible to put forth a putative explanation for the uncanny conformational preferences of crystalline 9 and 10.

A one-step technique to prepare aligned arrays of carbon nanotubes

A simple effective pyrolysis technique has been developed to synthesize aligned arrays of multi-walled carbon nanotubes (MWCNTs) without using any carrier gas in a single-stage furnace at 700 °C. This technique eliminates nearly the entire complex and expensive machinery associated with other extensively used methods for preparation of CNTs such as chemical vapour deposition (CVD) and pyrolysis. Carbon source materials such as xylene, cyclohexane, camphor, hexane, toluene, pyridine and benzene have been pyrolyzed separately with the catalyst source material ferrocene to obtain aligned arrays of MWCNTs. The synthesized CNTs have been characterized by scanning electron microscopy (SEM), x-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and Raman spectroscopy. In this technique, the need for the tedious and time-consuming preparation of metal catalysts and continuously fed carbon source material containing carrier gas can be avoided. This method is a single-step process where not many parameters are required to be monitored in order to prepare aligned MWCNTs. For the production of CNTs, the technique has great advantages such as low cost and easy operation.

Crystal Structures of a New Polymorphic Form of Gabapentin Monohydrate and the E and Z Isomers of 4-Tertiarybutylgabapentin

Gabapentin, a widely used antiepileptic drug, crystallizes in multiple polymorphic forms. A new crystal form of gabapentin monohydrate in the space group Pbca is reported and the packing arrangement compared with that of a previously reported polymorph in the space group P2(1)/c [Ibers, J.A. (2001) Acta Crystallogr; C57:641]. Gabapentin polymorphs can also occur from a selection of one of the two distinct chair forms of the 1,1-disubstituted cyclohexane. Crystal structures of the E and Z isomers of 4-tert-butylgabapentin provide models for analyzing anticipated packing modes in the conformational isomers of gabapentin. The E isomer crystallized in the space group Pca2(1), while the Z isomer crystallized in the space group P2(1)/c. The crystal structure of E-4-tert-butylgabapentin provides the only example of a structure in a non-centrosymmetric space group. Crystal structures of the hydrochloride and hydrobromide salts of 4-tert-butyl derivatives are reported. The results suggest that for gabapentin, a large 'polymorph-space' may be anticipated, in view of the multiple conformational states that are accessible to the molecule.

A new glucose: Towards conformationally locked flexoses through annulation

A new family of surf ace-modified carbohydrates with locked, axial-rich conformations and bipolarofacial architectures has been developed with the aid of carbocyclic ring annulation. These novel trans-decalin-based carbohydrates have been synthesized, from simple aromatic precursors such as tetralin, through the ozonolysis of an appropriately protected allylic alcohol, followed by a cascade of intramolecular acetalizations to generate the sugar pyran moiety. The stereoselective synthesis of (racemic) cyclohexane-annulated 0-glucopyranoside and a-glucofuranoside from a common annulated trans-cyclohexadiene diol (trans-CHD) precursor under-scores the versatility of our approach. The efficacy of the annulation stratagem in generating carbohydrate diversity has been demonstrated through the synthesis of two regioisomeric annulated gulose derivatives, which differ only in the site of ring annulation on the sugar moiety. The mapping of the MLP surface and solid-state architecture of the new sugar shows that cycloalkane annulation results in surface modification and fine-tuning of sugar hydrophilicity. (© Wiley-VCH Verlag GmbH & Co. KGaA, 69451 Weinheim, Germany, 2005).