Synthesis of nanoparticles of the giant dielectric material, CaCu3Ti4O12 from a precursor route

A complex oxalate precursor, CaCu3(TiO)(4)(C2O4)(8)center dot 9H(2)O, (CCT-OX), was synthesized and the precipitate that obtained was confirmed to be monophasic by the wet chemical analyses, X-ray diffraction, FTIR absorption and TG/DTA analyses. The thermal decomposition of this oxalate precursor led to the formation of phase-pure calcium copper titanate, CaCu3Ti4O12, (CCTO) at a parts per thousand yen680A degrees C. The bright-field TEM micrographs revealed that the size of the as synthesized crystallites to be in the 30-80 nm range. The powders so obtained had excellent sinterability resulting in high density ceramics which exhibited giant dielectric constants upto 40000 (1 kHz) at 25A degrees C, accompanied by low dielectric losses.

Remarkable Capacity Retention of Nanostructured Manganese Oxide upon Cycling as an Electrode Material for Supercapacitor

Electrochemical capacity retention of nearly X-ray amorphous nanostructured manganese oxide (nanoMnO2) synthesized by mixing directly KMnO4 with ethylene glycol under ambient conditions for supercapacitor studies is enhanced significantly. Although X-ray diffraction (XRD) pattern of nanoMnO2 shows poor crystallinity, it is found that by Mn K-edge X-ray absorption near edge structure (XANES) measurement that the nanoMnO2 obtained is locally arranged in a δ-MnO2-type layered structure composed of edge-shared network of MnO6 octahedra. Field emission scanning electron microscopy and XANES measurements show that nanoMnO2 contains nearly spherical shaped morphology with δ-MnO2 structure, and 1D nanorods of α-MnO2 type structure (powder XRD) in the annealed (600 °C) sample. Volumetric nitrogen adsorption−desorption isotherms, inductively coupled plasma analysis, and thermal analysis are carried out to obtain physicochemical properties such as surface area (230 m2 g−1), porosity of nanoMnO2 (secondary mesopores of diameter 14.5 nm), water content, composition, etc., which lead to the promising electrochemical properties as an electrode for supercapacitor. The nanoMnO2 shows a very high stability even after 1200 cycles with capacity retention of about 250 F g−1.

Diversity: Cultural and biological

Early human populations utilized a wide range of biological resources in a tremendous diversity of environments. As a result, they possessed high levels of cultural diversity dependent on and supportive of high levels of biological diversity. This pattern changed drastically with technological innovations enabling certain human groups to break down territorial barriers and to usurp resources of other groups. The dominant groups have gone on to exhaust a whole range of resources, depleting both biological and cultural diversity. Traditions of resource conservation can, however, re-emerge when the dominant cultures spread over the entire area and the innovations diffuse to other human groups. This could change once again as genetically engineered organisms become an economically viable proposition with the accruing advantages concentrated in the hands of a few human groups: a further drastic reduction in biological and cultural diversity may ensue.

Cultural-Evolution of Ecological Prudence

Animals often behave in a profligate fashion and decimate the populations of plants and animals they depend upon. They may, however, evolve prudent behaviour under special conditions, namely when such prudence greatly enhances the success of populations that are not too prone to invasions by profligate individuals. Cultural evolution in human societies can also lead to the adoption of prudent practices under similar conditions. These are more likely to be realized in stable environments in which the human populations tend to grow close to the carrying capacity, when the human groups are closed, and when the technology is stagnant. These conditions probably prevailed in the hunter—gatherer societies of the tropics and subtropics, and led to the adoption of a number of socially imposed restraints on the use of plant and animal resources. Such practices were rationalized in the form of Nature-worship. The Indian caste society became so organized as to fulfill these conditions, and gave rise to two religions, Buddhism and Jainism, which emphasize compassion towards all forms of life. The pastoral nomads of the middle east, on the other hand, lived in an environment which militated against prudence, and these societies gave rise to religions like Christianity, which declared war on nature. As the ruling elite and state have grown in power, they have tried to wrest control of natural resources from the local communities. This has sometimes resulted in conservation and prudent use under guidance from the state, but has often led to conflicts with local populations to the detriment of prudent behaviour. Modern technological progress has also often removed the need for conservation, as when availability of coal permitted the deforestation of England. While modern scientific understanding has led to a better appreciation of the need for prudence, the prevailing social and economic conditions often militate against any implementation of the understanding, as is seen from the history of whaling. However, the imperative for survival of the poor from the Third-World countries may finally bring about conditions in which ecological prudence may once again come to dominate human cultures as it might once have done with stable societies of hunter—gatherers.

Role of Melt Convection on the Thermal Performance of Heat Sinks with Phase Change Material

The role of melt convection oil the performance of beat sinks with Phase Change Material (PCM) is presented in this paper. The beat sink consists of aluminum plate fins embedded in PCM and heat flux is supplied from the bottom. The design of such a heat sink requires optimization with respect to its geometrical parameters. The objective of the optimization is to maximize the heat sink operation time for the prescribed heat flux and the critical chip temperature. The parameters considered for optimization are fin number and fill thickness. The height and base plate thickness of heat sink are kept constant in the present analysis. An enthalpy based CFD model is developed, which is capable Of Simulating phase change and associated melt convection. The CFD model is Coupled with Genetic Algorithm (GA) for carrying out the optimization. Two cases are considered, one without melt convection (conduction regime) and the other with convection. It is found that the geometrical optimizations of heat sinks are different for the two cases, indicating the importance of inch convection in the design of heat sinks with PCMs.

Modeling of dynamic material behavior in hot deformation: Forging of Ti-6242

A new method of modeling material behavior which accounts for the dynamic metallurgical processes occurring during hot deformation is presented. The approach in this method is to consider the workpiece as a dissipator of power in the total processing system and to evaluate the dissipated power co-contentJ = ∫o σ ε ⋅dσ from the constitutive equation relating the strain rate (ε) to the flow stress (σ). The optimum processing conditions of temperature and strain rate are those corresponding to the maximum or peak inJ. It is shown thatJ is related to the strain-rate sensitivity (m) of the material and reaches a maximum value(J max) whenm = 1. The efficiency of the power dissipation(J/J max) through metallurgical processes is shown to be an index of the dynamic behavior of the material and is useful in obtaining a unique combination of temperature and strain rate for processing and also in delineating the regions of internal fracture. In this method of modeling, noa priori knowledge or evaluation of the atomistic mechanisms is required, and the method is effective even when more than one dissipation process occurs, which is particularly advantageous in the hot processing of commercial alloys having complex microstructures. This method has been applied to modeling of the behavior of Ti-6242 during hot forging. The behavior of α+ β andβ preform microstructures has been exam-ined, and the results show that the optimum condition for hot forging of these preforms is obtained at 927 °C (1200 K) and a strain rate of 1CT•3 s•1. Variations in the efficiency of dissipation with temperature and strain rate are correlated with the dynamic microstructural changes occurring in the material.