Effects of different modes of hot cross-rolling in 7010 aluminum alloy: part I. evolution of microstructure and texture

The current study describes the evolution of microstructure and texture in an Al-Zn-Mg-Cu-Zr-based 7010 aluminum alloy during different modes of hot cross-rolling. Processing of materials involves three different types of cross-rolling. The development of texture in the one-step cross-rolled specimen can be described by a typical beta-fiber having the maximum intensity near Copper (Cu) component. However, for the multi-step cross-rolled specimens, the as-rolled texture is mainly characterized by a strong rotated-Brass (Bs) component and a very weak rotated-cube component. Subsequent heat treatment leads to sharpening of the major texture component (i.e., rotated-Bs). Furthermore, the main texture components in all the specimens appear to be significantly rotated in a complex manner away from their ideal positions because of non-symmetric deformations in the two rolling directions. Detailed microstructural study indicates that dynamic recovery is the dominant restoration mechanism operating during the hot rolling. During subsequent heat treatment, static recovery dominates, while a combination of particle-stimulated nucleation (PSN) and strain-induced grain boundary migration (SIBM) causes partial recrystallization of the grain structure. The aforementioned restoration mechanisms play an important role in the development of texture components. The textural development in the current study could be attributed to the combined effects of (a) cross-rolling and inter-pass annealing that reduce the intensity of Cu component after each successive pass, (b) recrystallization resistance of Bs-oriented grains, (c) stability of Bs texture under cross-rolling, and (d) Zener pinning by Al3Zr dispersoids.

Flow behavior of LDPE and its blends with LLDPE I and II: A comparative study

Studies on melt rheological properties of blends of low density polyethylene (LDPE) with selected grades of linear low density polyethylene (LLDPE), which differ widely in their melt flow indices, are reported, The data obtained in a capillary rheometer are presented to describe the effects of blend composition and shear rate on flow behavior index, melt viscosity, and melt elasticity. In general, blending of LLDPE I that has a low melt flow index (2 g/10 min) with LDPE results in a decrease of its melt viscosity, processing temperature, and the tendency of extrudate distortion, depending on blending ratio. A blending ratio around 20-30% LLDPE I seems optimum from the point of view of desirable improvement in processability behavior. On the other hand, blending of LLDPE II that has a high melt flow index (10 g/10 min) with LDPE offers a distinct advantage in increasing the pseudoplasticity of LDPE/LLDPE II blends.

Crystallization behaviour of polyethylene and i-polybutene-1 blends

The mutual influence of the components on the crystallization behaviour of polyblends, namely, isotactic polybutene-1 (PB) with low-density and high-density polyethylene (LDPE and HDPE), has been studied using techniques such as differential scanning calorimetry, infra-red spectroscopy, wide-angle X-ray diffraction, scanning electron microscopy, etc. Each component in the blend is observed to crystallize independently. There is phase separation and incompatibility, as shown from tensile properties and scanning electron microscopic observation of the fracture surface of the blend. For HDPE-PE blends (<30% HDPE), unusual form I′ crystals of PB are observed along with the usual form II.

Cloning and sequencing of winged bean (Psophocarpus tetragonolobus) basic agglutinin (WBA I): presence of second glycosylation site and its implications in quaternary structure

We report cloning of the DNA encoding winged bean basic agglutinin (WBA I). Using oligonucleotide primers corresponding to N- and C-termini of the mature lectin, the complete coding sequence for WBA I could be amplified from genomic DNA. DNA sequence determination by the chain termination method revealed the absence of any intervening sequences in the gene. The DNA deduced amino acid sequence of WBA I displayed some differences with its primary structure established previously by chemical means. Comparison of the sequence of WBA I with that of other legume lectins highlighted several interesting features, including the existence of the largest specificity determining loop which might account for its oligosaccharide-binding specificity and the presence of an additional N-glycosylation site. These data also throw some light on the relationship between the primary structure of the protein and its probable mode of dimerization.

Chelating and bridging diphosphinoamine (PPh2)(2)N(Pr-i) complexes of copper(I)

The ligand bis(diphenylphosphino) isopropylamine (dppipa) has been shown to be a versatile ligand sporting different coordination modes and geometries dictated by copper(I). Most of the molecular structures were confirmed by X-ray crystallography. It is found in a chelating mode, in a monomeric complex when the ligand to copper ratio is 2:1. A tetrameric complex is formed when low ratios of ligand to metal (1: 2) were used. But with increasing ratios of ligand to metal (1: 1 and 2: 1), a trimer or a dimer was obtained depending on the crystallization conditions. Variable temperature P-31{H-1} NMR spectra of these complexes in solution showed that the Cu-P bond was labile and the highly strained 4-membered structure chelate found in the solid state readily converted to a bridged structures. On the other hand, complexes with the ligand in a bridging mode in the solid state did not form chelated structures in solution. The effect of adding tetra-alkylammonium salts to solutions of various complexes of dppipa were probed by P-31{H-1} NMR and revealed the effect of counter ions on the stability of complexes in solution. (C) 2008 Elsevier B.V. All rights reserved.

Conformation of di-n-propylglycine residues (Dpg) in peptides: crystal structures of a type I-turn forming tetrapeptide and an -helical tetradecapeptide

The crystal structures of two oligopeptides containing di-n-propylglycine (Dpg) residues, Boc-Gly-Dpg-Gly-Leu-OMe (1) and Boc-Val-Ala-Leu-Dpg-Val-Ala-Leu-Val-Ala-Leu-Dpg-Val-Ala-Leu-OMe (2) are presented. Peptide 1 adopts a type I-turn conformation with Dpg(2)-Gly(3) at the corner positions. The 14-residue peptide 2 crystallizes with two molecules in the asymmetric unit, both of which adopt -helical conformations stabilized by 11 successive 5 1 hydrogen bonds. In addition, a single 4 1 hydrogen bond is also observed at the N-terminus. All five Dpg residues adopt backbone torsion angles (, ) in the helical region of conformational space. Evaluation of the available structural data on Dpg peptides confirm the correlation between backbone bond angle NCC() and the observed backbone , values. For > 106° , helices are observed, while fully extended structures are characterized by < 106° . The mean values for extended and folded conformations for the Dpg residue are 103.6° ± 1.7° and 109.9° ± 2.6° , respectively.

Perpetuation of immunological memory through common MHC-I binding modes of peptidomimic and antigenic peptides

Understanding the molecular mechanisms of immunological memory assumes importance in vaccine design. We had earlier hypothesized a mechanism for the maintenance of immunological memory through the operation of a network of idiotypic and anti-idiotypic antibodies (Ab2). Peptides derived from an internal image carrying anti-idiotypic antibody are hypothesized to facilitate the perpetuation of antigen specific T cell memory through similarity in peptide-MHC binding as that of the antigenic peptide. In the present work, the existence of such peptidomimics of the antigen in the Ab2 variable region and their similarity of MHC-I binding was examined by bioinformatics approaches. The analysis employing three known viral antigens and one tumor-associated antigen shows that peptidomimics from Ab2 variable regions have structurally similar MHC-I binding patterns as compared to antigenic peptides, indicating a structural basis for memory perpetuation. (C)) 2007 Elsevier Inc. All rights reserved.

Tuning the beta-turn segment in designed peptide beta-hairpins: Construction of a stable type I ' beta-turn nucleus and hairpin-helix transition promoting segments

Designed octapeptides Boc-Leu-Val-Val-Aib-(D)Xxx-Leu- Val-Val-OMe ((D)Xxx = (D)Ala, 3a; (D)Val, 3c and (D)Pro, 5a) and Boc-Leu-Phe-Val-Aib-DAla-Leu-Phe-Val-OMe (3b) have been investigated to construct models of a stable type I' beta-turn nucleated hairpin and to generate systems for investigating helix-hairpin conformational transitions. Peptide 5a, which contains a central Aib-(D)Pro segment, is shown to adopt a stable type I' beta-turn nucleated hairpin structure, stabilized by four cross-strand hydrogen bonds. The stability of the structure in diverse solvents is established by the observation of all diagnostic NOEs expected in a beta-hairpin conformation. Replacement of (D)Pro5 by (D)Ala/(D)Val (3a-c) results in sequences that form beta-hairpins in hydrogen bonding solvents like CD3OH and DMSO-d(6). However, in CDCl3 evidence for population of helical conformations is obtained. Peptide 6b (Boc-Leu-Phe-Val-Aib-Aib-Leu-Phe-Val-OMe), which contains a centrally positioned Aib-Aib segment, provides a clear example of a system, which exhibits a helical conformation in CDCl3 and a significant population of both helices and hairpins in CD3OH and DMSO-d(6). The coexistence of multiple conformations is established by the simultaneous observation of diagnostic NOEs. Control over stereochemistry of the central beta-turn permits generation of models for robust beta-hairpins and also for the construction of systems that may be used to probe helix-hairpin conformational transitions. (c) 2006 Wiley Periodicals, Inc.

The syntheses, characterizations, X-ray crystal structures and properties of Cu(I) complexes of a bis-bidentate schiff base ligand

Bis-bidentate Schiff base ligand L and its two mononuclear complexes [CuL(CH3CN)(2)]ClO4 (1)and [CuL(PPh3)(2)]ClO4 (2)have been prepared and thoroughly characterized by elemental analyses, IR, UV-Vis, NMR spectroscopy and X-ray diffraction analysis. In both the complexes the metal ion auxiliaries adopt tetrahedral coordination environment. Their reactivity, electrochemical and photophysical behavior have been studied. Complex 1 shows reversible Cu-II/I couple with potential 0.74 V versus Ag/AgCl in CH2Cl2. At room temperature L is weakly fluorescent in CH2Cl2, however in Cu(I)complexes 1 and 2 the emission in quenched. (C) 2009 Elsevier B. V. All rights reserved.

Biosynthesis of valine and isoleucine in plants I. Formation of α-acetolactate in Phaseolus radiatus

1. 1. The presence of an enzyme system in plants catalyzing the formation of α-acetolactate from pyruvate has been demonstrated; the system in green gram (Phaseolus radiatus) has been partially purified and its characteristics have been studied.2. Free acetaldehyde is formed as a product of the reaction and so the reaction is mainly diverted towards the formation of acetoin. 3. The system requires thiamine pyrophosphate and a divalent metal ion (Mn2+ or Mg2+) for maximum activity. The optimum pH is around 6.0 and the optimum temperature is 60°. 4. The system is very labile in absence of pyruvate, Mn2+ and DPT. 5. The Km values for pyruvate, Mn2+, Mg2+ and DPT are 3·10−2 M. 5·10−5 M, 2·10−5 M, and e·10−6 M respectively. The activation energy is 3540 cal/mole. 6. The enzyme is strongly inhibited by p-chloromercuribenzoate and the inhibition can be reversed partially by 2-mercaptoethanol, BAL or cysteine. Heavy metals, such as Hg2+ and Ag+, are inhibitory but l-valine does not inhibit the reaction.

Studies in the sandalwood-oil series. I. The structure, synthesis, and configuration of the lactone of tricycloekasantalic acid

The structure, synthesis, and configuration of the lactone of tricycloekasantalic acid have been described. It has been shown that in the formation of this lactone (XII) from the acids (I) or (II) a rearrangement is involved.

Am unexpected entry into the silver(I) chemistry of diphosphazane ligands: Crystal and molecular structures of [Ag{Ph2PN(Pr-i)PPh2}(CF3SO3)](2), [Ag{Ph2PN(Pr-i)PPh(OC6H3Me2-2,6)}(2)]PF6, and [Ag-3(mu-Cl)(2){Ph2PN(R)PPh2}(3)]PF6 (R = H, Pr-i)

Mononuclear, binuclear and trinuclear silver(l) complexes were obtained unexpectedly while probing the reactivity of diphosphazane ligands of the type X2PN(Pr-i)PXY towards the ruthenium-based precursor Ru(bipy)(2)Cl-2 center dot 2H(2)O, in the presence of a silver salt as a chloride scavenger. Subsequently, the reactions of AgX [X = Cl, NO3 or CF3SO3] with Ph2PN(R)PPh(Y) [R = H, Y = Ph; R = Pr-i, Y = Ph or OC6H3Me2-2,6] in a 1: 1 or 1:2 molar ratio have been investigated. Mononuclear or binuclear Ag(I) complexes containing either chelating or bridging diphosphazane ligands are obtained. Trinuclear silver(l) complexes are accessible by the treatment of diphosphazane ligands, Ph2PN(R)PPh2 [R = H, Pr-i] with AgCl using piperidine as the solvent. In the presence of a suitable chloride donor species, the mononuclear and binuclear complexes of Ph2PN(Pr-i)PPh2 are transformed slowly to the trinuclear complex [Ag-3(mu-Cl)(2){Ph2PN(Pr-i)PPh2}(3)]X, over a period 20 h. The structures of representative complexes have been confirmed by X-ray crystallography and the salient structural features are discussed

Simultaneous Measurement of Strain and Temperature using Type I and Pre-strained Fiber Bragg Gratings

Strain and temperature sensitivities of a type I Bragg grating inscribed in a germania doped silica fiber, fabricated under normal conditions and zero strain, are compared with that of a Bragg grating inscribed under pre-strained condition. The results obtained reveal that the strain and temperature sensitivities of the two gratings are different. Based on these results, we demonstrate a technique which enables discrimination of strain and temperature in a Fiber Bragg Grating (FBG) with a linear response. The present technique allows for an easy implementation of the sensor by providing a direct access to the grating region in the fiber and demands only a simple interrogation system.

Immediate hypersensitivity to Parthenium hysterophorus. I. Association of HLA antigens and Parthenium rhinitis

Lymphocytes collected from rhinitis subjects with strong positive skin reactions to the pollen allergens of Parthenium hysterophorus (American feverfew) having moderate to high titres of Parthenium-specific serum IgE were analysed for association of HLA-antigens covering 13 specificities of HLA-A, 17 specificities of HLA-B and eight specificities of HLA-DR loci by the NIH two-stage microlymphocytotoxicity assay. Comparison of the phenotypic frequencies of HLA-A and B antigens between Parthenium rhinitis subjects (n= 22) and control subjects (n= 137) did not suggest any significant association when tested for these antigen specificities. A significant correlation in the association of HLA-DR3 antigen with a relative risk of 11·33, however, was observed in Parthenium rhinitis subjects (n= 30) when compared to controls (n= 50).