Effect of disorder on the exponent in the coherence region in high temperature superconductors

Effect of disorder on the electrical resistance near the superconducting transition temperature in the paracoherence region of high temperature YBa2CU3O7-delta (YBCO) thin film superconductor is reported. For this, c-axis oriented YBa2Cu3O7-delta thin films having superconducting transition width varying between 0.27 K and 6 K were deposited using laser ablation and high pressure oxygen sputtering techniques. Disorder in these films was further created by using 100 MeV oxygen and 200 MeV silver ions with varying fluences. It is observed that the critical exponent in the paracoherence region for films with high transition temperature and small transition width is in agreement with the theoretically predicted value (gamma = 1.33) and is not affected by disorder, while for films with lower transition temperature and larger transition width the value of exponent is much larger as compared to that theoretically predicted and it varies from sample to sample and usually changes with disorder induced by radiation. This difference in the behaviour of the exponent has been explained on the basis of differences in the strength of weak links and the transition between temperatures T. and T, is interpreted as a percolation like transition with disorder. (c) 2006 Elsevier B.V. All rights reserved.

Texture evolution in high strain rate deformed Cu-10Zn alloy

High strain rate deformation behavior of Cu-10Zn alloy was studied. A weak texture with fine grain size was observed at high strain rate. The weak texture has been attributed to activity of higher number of slip systems under dynamic loading conditions. Twinning has minimal role on texture. (C) 2012 Elsevier B.V. All rights reserved.

Terminalia paniculata bark extract attenuates non-alcoholic fatty liver via down regulation of fatty acid synthase in high fat diet-fed obese rats

Background: This study was performed to understand the possible therapeutic activity of Terminalia paniculata ethanolic extract (TPEE) on non alcoholic fatty liver in rats fed with high fat diet. Methods: Thirty six SD rats were divided into 6 groups (n = 6): Normal control (NC), high fat diet (HFD), remaining four groups were fed on HFD along with different doses of TPEE (100,150 and 200 mg/kg b.wt) or orlistat, for ten weeks. Liver tissue was homogenized and analyzed for lipid profiles, activities of superoxide dismutase (SOD), catalase (CAT) and malondialdehyde (MDA) content. Further, the expression levels of FAS and AMPK-1 alpha were also studied in addition to histopathology examination of liver tissue in all the groups. Results: HFD significantly increased hepatic liver total cholesterol (TC), triglycerides (TG), free fatty acids (FFA) and MDA but decreased the activities of SOD and CAT which were subsequently reversed by supplementation with TPEE in a dose-dependent manner. In addition, TPEE administration significantly down regulated hepatic mRNA expression of FAS but up regulated AMPK-1 alpha compared to HFD alone fed group. Furthermore, western blot analysis of FAS has clearly demonstrated decreased expression of FAS in HFD + TPEE (200 mg/kg b. wt) treated group when compared to HFD group at protein level. Conclusions: Our biochemical studies on hepatic lipid profiles and antioxidant enzyme activities supported by histological and expression studies suggest a potential therapeutic role for TPEE in regulating obesity through FAS.

New initiators for the ring-opening thermal polymerization of hexachlorocyclotriphosphazene: synthesis of linear poly(dichlorophosphazene) in high yields

Ring-opening thermal polymerization of hexachlorocyclotriphosphazene (N3P3C&h)a s been investigated at 250 "C and at 1.333-Pa pressure using chlorocyclotriphosphazenes N3P3C15(N=PPh3) and N3P3Cl,.,(NMe2), (n = 2-4), salt hydrates, triphenylphosphine, and benzoic acid as initiators. The linear poly (dich1orophosphazene) products are phenoxylated, and the phenoxy polymers are characterized by gel permeation chromatography and dilute solution viscometry. Among the various initiators investigated, CaS04.2H20b rings about a high conversion (>60%) of N3P3C&to the linear [NPC12], polymer which possesses a high molecular weight (>5 X lo6). The rationale for the choice of the initiators and possible mechanism(s) of polymerization is discussed. Several mixed substituent polymers, [NP(OPh),(OC6H4Me-p)2,1, and [NP(OPh),(OCHzCF3)2,]nh, ave been prepared and their thermal properties evaluated.

Sequences that adopt non-B-DNA conformation in form V DNA as probed by enzymic methylation

pBR322 form V DNA is a highly torsionally strained molecule with a linking number of zero. We have used sequence- specific DNA methylases as probes for B-DNA in this molecule, exploiting the inability of methylases to methylate single-stranded DNA and Z-DNA, both of which are known to occur in form V DNA. Some sequences in form V DNA were shown to be totally in the B-form, others were totally in an altered, unmethylatable conformation, while still other sites appeared to exist partly in altered and partly in normal B-conformation. Some potential Z-forming sequences (alternating pyrimidine/purine) of less than seven base-pairs were not in the Z conformation in form V DNA, whereas others did adopt an altered structure, indicating a modulating influence of flanking sequences. Furthermore, regions of imperfect alternating pyrimidine/purine structure were sometimes capable of adopting an altered structure. In addition, some regions of altered structure had no apparent Z-forming sequences, nor were they in polypurine stretches, which have also been proposed to form left-handed DNA. These non-B-DNA conformations may represent novel left-handed helical structures or sequences that become single stranded under torsional strain. Long regions of either altered (unmethylatable) DNA or B-DNA were not always observed. In fact, one region showed three transitions between B-like DNA and altered structure within 26 base-pairs.

Engine wear and used oil analysis - comparative study in high speed diesel engines

The operational life and reliability of I.C. engines are limited to a certain extent by the break down of the engine components due to wear. It is advantageous to know the condition of an engine and its components without disassembling for detailed measurements. This paper describes the possibility of employing chemical analysis of the used crank case oil to predict the wear of engine components. It is concluded that the acidity and carbon contents of the crank case oil play a significant role in assessing the wear of copper-lead bearings used for the big end of the connecting rod.

Drag reduction by a forward facing aerospike for a large angle blunt cone in high enthalpy flows

Drag reduction studies are conducted using a flat disc tipped aerospike for a 120-degree apex angle blunt cone model in high enthalpy flows. Accelerometer based force balance is used for the drag force measurement in the newly established free piston driven shock tunnel, HST3. Drag reduction upto about 58 percent has been achieved for Mach 8 flow of 5 MJ/kg specific enthalpy at zero degree angle of attack.

Drag reduction by counterflow supersonic jet for a blunt cone in high enthalpy flows

Counterflow supersonic jet is used as a drag reduction device during the experiments in free piston driven shock tunnel, HST3. Accelerometer based force balance is employed to measure the drag force experienced by the 60-degree apex angle blunt cone model without and with the supersonic jet opposing the hypersonic flow. It is observed that the drag force decreases with increase in injection pressure ratio until the critical injection pressure is reached. Maximum reduction in drag force of 44 percent is recorded at the critical injection pressure ratio 22.36. Further increase in injection pressure ratio has reduced the percentage drag reduction. Change in nature of the flowfield around the model has also been observed across the critical injection pressure ratio.

Engine wear and used oil analysis-A comparative study in high speed diesel engines

The operational life and reliability of I.C. engines are limited to a certain extent by the break down of the engine components due to wear. It is advantageous to know the condition of an engine and its components without disassembling for detailed measurements. This paper describes the possibility of employing chemical analysis of the used crank case oil to predict the wear of engine components. It is concluded that the acidity and carbon contents of the crank case oil play a significant role in assessing the wear of copper-lead bearings used for the big end of the connecting rod.

Epoxy resin chamber for high voltage breakdown studies in high vacuum

As the study of electrical breakdown phenomena in vacuum systems, gains more importance, a thorough understanding of the breakdown mechanism at high voltages necessitates a chamber for experimental studies. An epoxy-resin chamber has been constructed by casting ring sections which were joined together. The advantages of such a chamber over the conventional metal or glass chamber are given especially as regards the electric field configuration, high voltage lead-in, and the ease of construction. Special facilities can be incorporated while constructing the chamber which makes it more versatile; for example, in pre-breakdown current measurements, electron beam focusing studies, etc.

b-Turn conformations in crystal structures of model peptides containing a,a-di-n-propylglycine (Dpg) and a,a-di-n-butyl-glycine (Dbg).

The crystal state conformations of three peptides containing the a,a-dialkylated residues, a,adi n-propylglycine (Dpg) and a,@-di-n-butylglycine (Dbg), have been established by x-ray diffraction. Boc-Ala-Dpg-Ala-OMe ( I ) and Boc-Ala-Dbg-Ala-OMe (III) adopt distorted type II @-turn conformations with Ala ( I ) and Dpg/Dbg (2) as the corner residues. In both peptides the conformational angles at the Dxg residue (I: 4 = 66.23 J/ = 19.3'; III: 4 = 66S0, J. = 21 .la)deviate appreciablyfrom ideal values for the i + 2 residue in a type II @-turn. In both peptides the observed(N. 0) distances between the Boc CO andAla(3) NHgroups are far too long (I:3.44 k; III: 3.63 k) for an intramolecular 4 + 1 hydrogen bond. Boc-Ala-Dpg-Ala-NHMe (II)crystallizes with two independent molecules in the asymmetric unit. Both molecules IIA and IIB adopt consecutive @-turn (type III-III in IIA and type III-I in IIB) or incipient 3,,,-helical structures, stabilized by two intramolecular 4 --t I hydrogen bonds. In all four molecules the bond angle N-C"-C' ( T ) at the Dxg residues are 2 1109 The observation of conformational angles in the helical region of 4,J/ space at these residues is consistent with theoretical predictions

Lipid-amphotericin B complex structure in solution: A possible first step in the aggregation process in cell membranes

The interactions between the polyene antibiotic amphotericin B with dipalmitoylphosphatidylcholine were investigated in vesicles (using circular dichroism) and in chloroform solution (using circular dichroism and IH, I3C, and 31P nuclear magnetic resonance). The results show that amphotericin B readily aggregates in vesicles and that the extent of aggregation depends on the 1ipid:drug concentration ratio. Introduction of sterol molecules into the membrane hastens the process of aggregation of amphotericin B. In chloroform solutions amphotericin B strongly interacts with phospholipid molecules to form a stoichiometric complex. The results suggest that there are interactions between the conjugated heptene stretch of amphotericin B and the methylene groups of lipid acyl chains, while the sugar moiety interacts with the phosphate head group by the formation of a hydrogen bond. A model is proposed for the lipid-amphotericin B complex, in which amphotericin B interacts equally well with the two lipid acyl chains, forming a 1:l complex.

Ultracapacitor Based Ride Through System for Control Power Supplies in High Power Converters

High power converters are used in variable speed induction motor drive applications. Riding through a short term power supply glitch is becoming an important requirement in these power converters. The power converter uses a large number of control circuit boards for its operation. The control power supply need to ensure that any glitch in the grid side does not affect any of these control circuit boards. A power supply failure of these control cards results in shut down of the entire system. The paper discusses the ride through system developed to overcome voltage sags and short duration outages at the power supply terminals of the control cards in these converters. A 240VA non-isolated, bi-directional buck-boost converter has been designed to be used along with a stack of ultracapacitors to achieve the same. A micro-controller based digital control platform made use of to achieve the control objective. The design of the ultracapacitor stack and the bidirectional converter is described the performance of the experimental set-up is evaluated.