Load-Commutated SCR Current-Source-Inverter-Fed Induction Motor Drive With Sinusoidal Motor Voltage and Current

Current source inverter (CSI) is an attractive solution in high-power drives. The conventional gate turn-off thyristor (GTO) based CSI-fed induction motor drives suffer from drawbacks such as low-frequency torque pulsation, harmonic heating, and unstable operation at low-speed ranges. These drawbacks can be overcome by connecting a current-controlled voltage source inverter (VSI) across the motor terminal replacing the bulky ac capacitors. The VSI provides the harmonic currents, which results in sinusoidal motor voltage and current even with the CSI switching at fundamental frequency. This paper proposes a CSI-fed induction motor drive scheme where GTOs are replaced by thyristors in the CSI without any external circuit to assist the turning off of the thyristors. Here, the current-controlled VSI, connected in shunt, is designed to supply the volt ampere reactive requirement of the induction motor, and the CSI is made to operate in leading power factor mode such that the thyristors in the CSI are autosequentially turned off. The resulting drive will be able to feed medium-voltage, high-power induction motors directly. A sensorless vector-controlled CSI drive based on the proposed configuration is developed. The experimental results from a 5 hp prototype are presented. Experimental results show that the proposed drive has stable operation throughout the operating range of speeds.

Study of liquid fuel transport in a small carburetted engine in the context of cold-start HC emission control

In the present study, a detailed visualization of the transport of fuel film has been performed in a small carburetted engine with a transparent manifold at the exit of the carburettor. The presence of fuel film is observed significantly on the lower half of the manifold at idling, while at load conditions, the film is found to be distributed all throughout the manifold walls. Quantitative measurement of the fuel film in a specially-designed manifold of square cross section has also been performed using the planar laser-induced fluorescence (PLIF) technique. The measured fuel film thickness is observed to be of the order of 1 nun at idling, and in the range of 0.1 to 0.4 mm over the range of load and speed studied. These engine studies are complemented by experiments conducted in a carburettor rig to study the state of the fuel exiting the carburettor. Laser-based Particle/Droplet Image Analysis (PDIA) technique is used to identify fuel droplets and ligaments and estimate droplet diameters. At a throttle position corresponding to idling, the fuel exiting the carburettor is found to consist of very fine droplets of size less than 15 mu m and large fuel ligaments associated with length scales of the order of 500 mu m and higher. For a constant pressure difference across the carburettor, the fuel consists of droplets with an SMD of the order of 30 mu m. Also, the effect of liquid fuel film on the cold start HC emissions is studied. Based on the understanding obtained from these studies, strategies such as manifold heating and varying carburettor main jet nozzle diameter are implemented. These are observed to reduce emissions under both idling and varying load conditions.

A role for nocturnal serum testosterone surge in regulating spermatogenesis in the adult non-human primate

Adult male bonnet monkeys exhibit nychthemeral rhythms in testosterone (T) secretion but the precise role of this heightened level of T secretion in regulating spermatogenesis is not known. Intranasal administration of microdoses (500 mu g or 250 mu g/day) of Norethisterone (IN-NET) to adult monkeys (n = 6) at 1600 h each day selectively and completely suppressed the nocturnal surge levels of serum T. Concomitant with this was a significant reduction (P<0.01) in serum LH but not FSH levels. DNA flow cytometric analysis of testicular biopsy tissue showed by week 10 of IN-NET treatment an arrest in meiotic transformation of primary spermatocytes (4C) to round/elongate (1C/HC) spermatids and by week 20 there was a complete absence of 4C, 1C and HC cells (with a relative accumulation in 2C cells). The accumulated meiotic (4C) cells at week 10 showed an increase (>80%, P<0.01) in coefficient of variation and a decrease in intensity of DNA-bound ethidium bromide fluorescence, parameters characteristic of degenerating 'apoptotic' subpopulation of germ cells. While two monkeys exhibited acute oligozoospermia 4 became azoospermic by 20 weeks of IN-NET treatment. A complete, qualitative reversal in the regressive changes in spermatogenesis and near-normal sperm output were apparent at the end of a 20-week recovery phase. These data demonstrate that prolonged, selective suppression of nocturnal surge levels of serum T secretion exerts a primary effect on meiosis in spermatogenesis leading to oligo/azoospermic status in adult bonnet monkeys.

Complexes of lanthanide perchlorates with two new O,N,O ligands derived from antipyraldehyde and acetic and benzoic acid hydrazides

Antipyrine is a well known ligand for lanthanides (I). A forage through the organic literature of pyrazolones reveals that the 4-position of antipyrine is amenable to a wide variety of organic reactions. It should thus be possible to introduce suitable functional groups at this position and design new multidentate ligands for metal ions. It is also found that the coordination chemistry of lanthanides is much less well developed and far fewer ligands have been used for complexation with lanthanide ions compared to that of the d-transition metal ions. Keeping these points in view we have reported earlier, complexes of lanthanides with a bidentate ligand N,N-diethyl-antipyrine-4-carboxamide (2). In this communication we report the synthesis of two new ligands from Schiff base condensation of antipyraldehyde and the hydrazides of acetic and benzoic acids and the complexes formed by these hydrazones with lanthanide perchlorates.

Ce1-xRuxO2-delta (x=0.05, 0.10): A New High Oxygen Storage Material and Pt, Pd-Free Three-Way Catalyst

Nanocrystalline Ce1-xRuxO2-delta (x = 0.05 and 0.10) of 8-10 nm sizes have been synthesized by hydrothermal method using melamine as complexing agent. Compounds have been characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and energy-dispersive X-ray analysis (EDX) and their structures have been refined by the Rietveld method.The compounds crystallize in fluorite structure and the composition is Ce1-xRuxO2-x/2 where Ru is in +4 state and Ce is in mixed-valence (+3, +4) state. Substitution of Ru4+ ion in CeO2 activated the lattice oxygen. Ce1-xRuxO2-x/2 reversibly releases 0.22[O] and 0.42[O] for x = 0.05 and 0.10, respectively, which is higher than the maximumpossible OSC of 0.22 [O] observed for Ce0.50Zr0.50O2. Utilization of Higher OSC of Ce1-xRuxO2-delta (x = 0.05 and 0.10) is also reflected in terms of low-temperature CO oxidation with these catalysts, both in the presence and absence of feed oxygen. The Ru4+ ion acts as an active center for reducing molecules (CO, hydrocarbon ``HC'') and oxide ion vacancy acts as an active center for O-2 and NO, leading to low-temperature NO conversion to N-2. Thus due to Ru4+ ion, Ce1-xRuxO2-delta is not just a high oxygen storage material but also shows high activity toward CO, hydrocarbon ``HC'' oxidation, and NO reduction by CO at low temperature with high N-2 selectivity for three-way catalysis.

Complexity analysis of EEG in patients with schizophrenia using fractal dimension

We computed Higuchi's fractal dimension (FD) of resting, eyes closed EEG recorded from 30 scalp locations in 18 male neuroleptic-naive, recent-onset schizophrenia (NRS) subjects and 15 male healthy control (HC) subjects, who were group-matched for age. Schizophrenia patients showed a diffuse reduction of FD except in the bilateral temporal and occipital regions, with the reduction being most prominent bifrontally. The positive symptom (PS) schizophrenia subjects showed FD values similar to or even higher than HC in the bilateral temporo-occipital regions, along with a co-existent bifrontal FD reduction as noted in the overall sample of NRS. In contrast, this increase in FD values in the bilateral temporo-occipital region was absent in the negative symptom (NS) subgroup. The regional differences in complexity suggested by these findings may reflect the aberrant brain dynamics underlying the pathophysiology of schizophrenia and its symptom dimensions. Higuchi's method of measuring FD directly in the time domain provides an alternative for the more computationally intensive nonlinear methods of estimating EEG complexity.

Is 3'-nucleotide rigid?

Conformational analysis of nucleic acids and polynucleotides is far more complex than that of proteins and polypeptides, due to five single bond rotations in addition to the sugar puckerings in the monomer. Sundaralingam1 proposed the concept of the 'rigid' nucleotides from analysis of crystal structure data, with the flexibility allowed only about the phosphodiester bonds. However, the crystal structure of deoxyguanosine-5'−phosphate2,3 indicates at gt conformation about the C-4'−C-5' bond against gg in a conformationally rigid nudeotide1. Jack et al. 4 considered the flexibility of nucleotides in tRNA about the C-4'−C-5' bond, thereby introducing the concept of 'non-rigid' ribonucleotides. Conformational flexibility of the f uranose ring in DNA and RNA and their energetics using classical and quantum chemical methods have been reported5−8. We have examined the flexibility of 3'-nucleotides. alpha, the most important of the conformational parameters defining the 3'-end of a nucleotide unit9, has a value in the range 195°−270° in all the 3'-nucleotides, dinucleoside monophosphates and higher oligomers which have been surveyed. A survey of the proposed structures of polyribonudeotides10,11 also shows the values of a to be greater than 200°. However, the structures proposed for B-DNA by Arnott and Hukins12,13 and D-DNA by Arnott et al. 14 have values of alpha of 155° and 141° respectively, much lower than the lowest observed value. The structure for B-DNA has two strong, short contacts (C-2'...OP-1 = 2.64 Å and HC-2"...OP-1 = 1.79 Å) which lead to an energetically unfavourable conformation. Hence, it is of interest to investigate whether, by allowing flexibility to the sugar moiety in the nucleotide unit, it is possible to make the structure energetically favourable. Here, conformational energy calculations were carried out to determine the range of alpha which would give rise to energetically favoured conformations with different sugar puckerings. Our analysis has shown that the theoretically obtained range is nearly the same as the preferred range in crystals, indicating the flexibility of the 3'-nucleotides.

Novel photoisomerization of spirodienones

Spironaphthalenones of the type (Image ) have been demonstrated to undergo isomerization to (Image ) upon UV irradiation.

The interference environment of radio Noise froh4 lightning

The paper furnishes a review and air ovendepr "f radio noise *om lightning as rr so~irce of interference to analogue and digital Corn?tunicatioiz. The parameters of fhe different fornls < f, noise necessary .for pssessigth e interfering effect of the rloise are described. 4railublr irfjrncroiun thrr tndevstor71zs, thunder-clouds, convecrion cells and lightning are er ieveadn d their liizitatimsp ointed oui. Thew fol101r.s a descripiicn of how the source, popugafiona nd receiver chaacteristidse termine the sfrticture qf a/rnosplro.ic noise as receiwd at a point of observation. The tratrrral unit for this noise i.s the mise burst rtrising from o w complete lightning.flas4. The pmuneters of the nrise birrst as a 11.hole and its structure ctetennine the inrqfflrrence enrirnniient. A hisforic reriel$. qf t2sophericii oke .studies sho1(5 that it i. wrreirt(v of importance oldy in thc ropicarl egions of' the wr ldf i>rs hichf hc neailable data are wry defective. New data are ficnrished. The contribution of atmospheric noise for backgrouzd interference even in remote places ,for r.adicj astronomy at VHF is firrnished. The imporlance of aimcspizeric nctise cceurring ;vporadiea@ in high values fur slzort inier.als at VHF and higher frequencies in the tropics is brought out.

Emissions from India's transport sector: Statewise synthesis

A decentralized emission inventories are prepared for road transport sector of India in order to design and implement suitable technologies and policies for appropriate mitigation measures. Globalization and liberalization policies of the government in 90's have increased the number of road vehicles nearly 92.6% from 1980-1981 to 2003-2004. These vehicles mainly consume non-renewable fossil fuels, and are a major contributor of green house gases, particularly CO2 emission. This paper focuses on the statewise road transport emissions (CO2, CH4, CO, N-x, N2O, SO2, PM and HC) using region specific mass emission factors for each type of vehicles. The country level emissions (CO2, CH4, CO, NOx, N2O, SO2 and NMVOC) are calculated for railways, shipping and airway, based on fuel types. In India, transport sector emits an estimated 258.10 Tg Of CO2, of which 94.5% was contributed by road transport (2003-2004). Among all the states and Union Territories, Maharashtra's contribution is the largest, 28.85 Tg (11.8%) Of CO2, followed by Tamil Nadu 26.41 Tg(10.8%), Gujarat 23.31 Tg(9.6%), Uttar Pradesh 17.42 Tg(7.1%), Rajasthan 15.17 Tg (6.22%) and, Karnataka 15.09 Tg (6.19%). These six states account for 51.8% of the CO2 emissions from road transport.

Preparation temperature effect on the synthesis of various carbon nanostructures

Various carbon nanostructures (CNs) have been prepared by a simple deposition technique based on the pyrolysis of a new carbon source material tetrahydrofuran (THF) mixed with ferrocene using quartz tube reactor in the temperature range 700-1100 degrees C. A detailed study of how the synthesis parameter such as growth temperature affects the morphology of the carbon nanostructures is presented. The obtained CNs are investigated by scanning electron microscope (SEM), X-ray diffraction (XRD), electron dispersive scattering (EDS)thermogravimetry analysis (TGA), Raman and transmission electron microscope (TEM). It is observed that at 700 degrees C. normal CNTs are formed. Iron filled multi-walled carbon nanotubes (MWCNTs) and carbon nanoribbons (CNRs) are formed at 950 degrees C. Magnetic characterization of iron filled MWCNTs and CNRs studied at 300 K by superconducting quantum interference device (SQUID) reveals that these nanostructures have an enhanced coercivity (Hc = 1049 Oe) higher than that of bulk Fe. The large shape anisotropy of MWCNTs, which act on the encapsulated material (Fe), is attributed for the contribution of the higher coercivity. Coiled carbon nanotubes (CCNTs) were obtained as main products in large quantities at temperature 1100 degrees C.

Changes in testicular function following specific deprivation of LH in the adult male rabbit

Sexually mature male rabbits actively immunized against highly purified ovine LH (oLH) were used as a model system to study the effects of endogenous LH deprivation (and therefore testosterone) on spermatogenesis as well as pituitary FSH secretion. Immunization against oLH generated antibody titres capable of cross-reacting and neutralizing rabbit LH and this resulted in a significant reduction (P<0.01) in serum testosterone levels by 2-4 weeks of immunization. A significant increase in circulating FSH concentration (from a basal level of similar to 1 ng to 60-100 ng/ml; P<0.01) was observed within 4-6 weeks of immunization, perhaps a consequence of the negative feedback effect of the lack of testosterone. The effect of LH deprivation on spermatogenesis assessed by DNA flow cytometry and histological analyses of testicular biopsy tissue revealed that lack of testosterone primarily results in a rapid reduction and complete absence of round (1C) and elongated (HC) spermatids. The immediate effect of LH/testosterone deprivation thus appears to be at the step of meiotic transformation of primary spermatocytes (4C) to 1C. A significant reduction (>80%; P<0.01) in the 4C population and a relative accumulation (>90%; P<0.01) in spermatogonia (2C) was also observed, suggesting a need for testosterone during the transformation of 2C to 1C. In all but one of the rabbits, both qualitative and quantitative recovery in spermatogenesis occurred during the recovery phase, even at a time when only a marginal increase in serum testosterone (compared with the preimmunization) levels was observed as a result of a rapid decline in the cross-reactive antibody titres. These results clearly show that LH/testosterone deprivation in addition to primarily affecting the meiotic step also regulates the conversion of 2C to 4C during spermatogenesis.

Surfactant-Mediated Synthesis of Functional Metal Oxide Nanostructures Via Microwave Irradiation-Assisted Chemical Synthesis

In the present work we report a rapid microwave irradiation-assisted chemical synthesis technique for the growth of nanoparticles, nanorods, and nanotubes of a variety of metal oxides in the presence of an appropriate surfactant (cationic, anionic, non ionic and polymeric), without the use of any templates. The method is simple, inexpensive, and helps one to prepare nanostructures in quick time, measured in seconds and minutes. This method has been applied successfully to synthesize nanostructures of a variety of binary and ternary metal oxides such as ZnO, CdO, Fe2O3, CuO, Ga2O3, Gd2O3, ZnFe2O4, etc. There is an observed variation in the morphology of the nanostructures with changes in different process parameters, such as microwave power, irradiation time, identity of solvent, type of surfactant, and its concentration.

Hydrocarbon oxidation and three-way catalytic activity on a single step directly coated cordierite monolith: High catalytic activity of Ce0.98Pd0.02O2−δ

Catalytic activity of cordierite honeycomb by a completely new coating method for the oxidation of major hydrocarbons in exhaust gas is reported here. The new coating process consists of (a) dipping and growing γ-Al2O3 on cordierite by combustion of monolith dipped in the aqueous solution of Al(NO3)3 and oxalyldihydrazide (ODH) (or glycine) at 600 °C and active catalyst phase Ce0.98Pd0.02O2−δ on γ-Al2O3-coated cordierite again by combustion of monolith dipped in the aqueous solution of ceric ammonium nitrate, ODH and 1.2 × 10−3 M PdCl2 solution at 500 °C. Weight of active catalyst can be varied from 0.02 wt% to 2 wt% which is sufficient but can be loaded even up to 12 wt% by repeating dip dry combustion. Adhesion of catalyst to cordierite surface is via oxide growth, which is very strong. ‘HC’ oxidation over the monolith catalyst is carried out with a mixture having the composition, 470 ppm of both propene and propane and 870 ppm of both ethylene and acetylene with the varying amount of O2. Three-way catalytic test is done by putting hydrocarbon mixture along with CO (10 000 ppm), NO (2000 ppm) and O2 (15 000 ppm). Below 350 °C full conversion is achieved. In this method, handling of nano-material powder is avoided.