Flow through a plateau border of cellular foam

Experimentally measured average velocities through plateau borders of stationary cellular foam, when compared with those calculated with the assumption of rigid Plateau Border walls, show that the assumption of rigid walls severely underestimates the velocities. An analysis of the situation wherein plateau border walls have velocities, as decided by the surface viscosity of the system, is presented here. The plateau border is idealized as a pipe of equilateral triangular cross-section with vertices of the triangle having zero velocity. The pertinent form of Navier-Stoke's equations with inhomogeneous boundary conditions and its solution through a procedure of successive approximations is presented in dimensionless form. The solution reduces to the known solution of slow steady flow through a triangular pipe, when surface viscosity is infinite. Results indicate that the assumption of rigid plateau border walls is valid only when value of the inverse of dimensionless surface viscosity is less than 0.044. Beyond that the assumption severely underestimates the flow and the effect of nonrigidity of the wall must be considered.

A compiler writing system based on affix grammars

We present an algorithm for testing the suitability of an affix grammar for deterministic, one-pass, bottom-up parsing which is an improvement over the one suggested by Pohlmann [1]. The space requirements of the new algorithm are considerably less than that of Pohlmann's. We also describe an implementation of Pohlmann's algorithm and methods for improving its space requirements.

Direct Writing of Copper Film Patterns by Laser-Induced Decomposition of Copper Acetate

Direct writing of patterns is being widely attempted in the field of microelectronic circuit/device manufacture. Use of this technique eliminates the need for employing photolithographic process. Laser induced direct writing can be achieved by (i) Photochemical reaction [i] , (ii) Evaporation from target material [2], and (iii) decomposition.Micron size features of palladium and copper through decomposition of palladium acetate and copper formate respectively on quartz and silicon using Argon ion laser have been reported [3,4] .In this commuication we report a technique for both single line and large area depositon of copper through decomposition of copper acetate,(CH3COO)2Cu, on alumina substrates.Nd:YAG laser known for its reliability and low maintenance cost as compared to excimer and other gas lasers is used. This technique offers an attractive and economical alternative for manufacture of thin film microcircuits.

High contrast laser writing in insitu textured germanium films via a novel chemical oxide formation

A high contrast laser writing technique based on laser induced efficient chemical oxidation in insitu textured Ge films is demonstrated. Free running Nd-YAG laser pulses are used for irradiating the films. The irradiation effects have been characterised using optical microscopy, electron spectroscopy and microdensitometry. The mechanism for the observed contrast has been identified as due to formation of GeO2 phase upon laser irradiation using X-ray initiated Auger spectroscopy (XAES) and X-ray photoelectron spectroscopy (XPS). The contrast in the present films is found to be nearly five times more than that known due to GeO phase formation in similar films.

Border basis detection is NP-complete

Border basis detection (BBD) is described as follows: given a set of generators of an ideal, decide whether that set of generators is a border basis of the ideal with respect to some order ideal. The motivation for this problem comes from a similar problem related to Grobner bases termed as Grobner basis detection (GBD) which was proposed by Gritzmann and Sturmfels (1993). GBD was shown to be NP-hard by Sturmfels and Wiegelmann (1996). In this paper, we investigate the computational complexity of BBD and show that it is NP-complete.

Note on high aspect-ratio SU-8 micromechanical structures using mask-less direct laser writing

We report high aspect-ratio micromechanical structures made of SU-8 polymer, which is a negative photoresist. Mask-less direct writing with 405 nm laser is used to pattern spin-cast SU-8 films of thickness of more than 600 um. As compared with X-ray lithography, which helps pattern material to give aspect ratios of 1:50 or higher, laser writing is a less expensive and more accessible alternative. In this work, aspect ratios up to 1:30 were obtained on narrow pillars and cantilever structures. Deep vertical patterning was achieved in multiple exposures of the surface with varying dosages given at periodic intervals of sufficient duration. It was found that a time lag between successive exposures at the same location helps the material recover from the transient changes that occur during exposure to the laser. This gives vertical sidewalls to the resulting structures. The time-lags and dosages were determined by conducting several trials. The micromechanical structures obtained with laser writing are compared with those obtained with traditional UV lithography as well as e-beam lithography. Laser writing gives not only high aspect ratios but also narrow gaps whereas e-beam can only give narrow gaps over very small depths. Unlike traditional UV lithography, laser writing does not need a mask. Furthermore, there is no adjustment for varying the dosage in traditional UV lithography. A drawback of this method compared to UV lithography is that the writing time increases. Some test structures as well as a compliant microgripper are fabricated.

Recent freshwater Ostracoda and Bivalvia from Indo-Nepal border (Tethys Himalaya): Ecological implications

We report for the first time Recent ostracods and bivalves from Central Tethys Himalaya, collected from Changru village, which is situated in the Tinker valley of northwestern Nepal near the Indo-Nepal border. The specimens were collected from the surface sediments of a small pond, shaped by a small tributary of the glacier fed Tinker River. The ostracod species belonging to the families Ilyocyprididae, Cyprididae and Candonidae and one bivalve (Pisidium sp., Family Pisidiidae) have been identified. Psychrodromus olivaccus and Potamocypris villosa are being reported for the first time from India and Nepal. Several broken and unidentifiable gyrogonites of charophyta were also recovered. The ostracod sample, as a whole, points to a shallow freshwater lake environment influenced by slowly running carbonate rich waters under cool temperatures, low mineralization and sparse vegetation. This is in accordance with the occurrence of Pisidium, which is commonly associated with ostracods in the freshwater lakes and streams. The ostracod fauna shows affinity with the fossil and extant forms recovered from the Higher and Tethys Himalaya of NW India. This opens a new opportunity for studying ostracods in the Indian Central Himalaya - a region which otherwise has been ignored until now.