Cement stabilised rammed earth. Part B: compressive strength and stress-strain characteristics

Strength and behaviour of cement stabilised rammed earth (CSRE) is a scantily explored area. The present study is focused on the strength and elastic properties of CSRE. Characteristics of CSRE are influenced by soil composition, density of rammed earth, cement and moisture content. The study is focused on examining (a) role of clay content of the soil on strength of CSRE and arriving at optimum clay fraction of the soil mix, (b) influence of moisture content, cement content and density on strength and (c) stress-strain relationships and elastic properties for CSRE. Major conclusions are (a) there is considerable difference between dry and wet compressive strength of CSRE and the wet to dry strength ratio depends upon the clay fraction of soil mix and cement content, (b) optimum clay fraction yielding maximum compressive strength for CSRE is about 16%, (c) strength of CSRE is highly sensitive to density and for a 20% increase in density the strength increases by 300-500% and (d) in dry state the ultimate strain at failure for CSRE is as high as 1.5%, which is unusual for brittle materials.

Stress-strain response of plastic waste mixed soil

Recycling plastic waste from water bottles has become one of the major challenges worldwide. The present study provides an approach for the use plastic waste as reinforcement material in soil. The experimental results in the form of stress-strain-pore water pressure response are presented. Based on experimental test results, it is observed that the strength of soil is improved and compressibility reduced significantly with addition of a small percentage of plastic waste to the soil. The use of the improvement in strength and compressibility response due to inclusion of plastic waste can be advantageously used in bearing capacity improvement and settlement reduction in the design of shallow foundations. (C) 2010 Elsevier Ltd. All rights reserved.

A salt of a protonated (amino)spirocyclic cyclotriphosphazene

The title compound 4,4,6,6-tetrakis(dimethylamino)-2 lambda(5),4 lambda(5),6 lambda(5)-cyclotriphosphaza- 1,3,5-trien-1-ium-2-spiro-2'-(2'-phospha-1',3'-diazacyclohexane) tetrachloroplatinate, [HN3P3(NMe(2))(4)(NHCH2CH2CH2NH)](2)-[PtCl4], contains a cyclophosphazenium cation in which the hetero-substituted (amino)spirocyclic cyclotriphosphazene is protonated. The protonation has occurred on one of the P3N3 ring N atoms adjacent to the spiro P atom. The protonation results in lengthening of the ring P-N bonds and puckering of the phosphazene ring. In the crystal lattice, 2n cyclophosphazenium cations are connected by n [PtCl4](2-) anions mediated by N-H...Cl hydrogen bonds to form a linear polymeric structure.

Dielectric Relaxation Spectroscopy for Evaluation of the Influence of Solvent Dynamics on Ion Transport in Succinonitrile-Salt Plastic Crystalline Electrolytes

Influence of succinonitrile (SN) dynamics on ion transport in SN-lithium perchlorate (LiClO4) electrolytes is discussed here via dielectric relaxation spectroscopy. Dielectric relaxation spectroscopy (similar to 2 x 10(-3) Hz to 3 MHz) of SN and SN-LiClO4 was studied as a function of salt content (up to 7 mol % or 1 M) and temperature (-20 to +60 degrees C). Analyses of real and imaginary parts of permittivity convincingly reveal the influence Of trans gauche isomerism and solvent-salt association (solvation) effects on ion transport. The relaxation processes are highly dependent on the salt concentration and temperature. While pristine SN display only intrinsic dynamics (i.e., trans-gauche isomerism) which enhances with an increase in temperature, SN-LiClO4 electrolytes especially at high salt concentrations (similar to 0.04-1 M) show salt-induced relaxation processes. In the concentrated electrolytes, the intrinsic dynamics was observed to be a function of salt content, becoming faster with an increase in salt concentration. Deconvolution of the imaginary part of the permittivity spectra using Havriliak-Negami (HN) function show a relaxation process corresponding to the above phenomena. The permittivity data analyzed using HN and Kohlrausch-Williams-Watta (KWW) functions show non-Debye relaxation processes and enhancement in the trans phase (enhanced solvent dynamics) as a function of salt concentration and temperature.

A Non-contact measurement technique to measure micro surface stress and obtain deformation profiles of the order of 1nm in Micro-cantilever based structures by single image Optical Diffraction method

A new method based on analysis of a single diffraction pattern is proposed to measure deflections in micro-cantilever (MC) based sensor probes, achieving typical deflection resolutions of 1nm and surface stress changes of 50 mu N/m. The proposed method employs a double MC structure where the deflection of one of the micro-cantilevers relative to the other due to surface stress changes results in a linear shift of intensity maxima of the Fraunhofer diffraction pattern of the transilluminated MC. Measurement of such shifts in the intensity maxima of a particular order along the length of the structure can be done to an accuracy of 0.01mm leading to the proposed sensitivity of deflection measurement in a typical microcantilever. This method can overcome the fundamental measurement sensitivity limit set by diffraction and pointing stability of laser beam in the widely used Optical Beam Deflection method (OBDM).

Stress-state-permeability relations for overconsolidated clays

Analysis of experimental data of soils in both the normally consolidated and overconsolidated states reveal that the proposed relationships are tenable. Preconsolidation stress level influences the level of permeability.

Effect of open joint on stress wave propagation

Stress wave characteristics are drastically altered by joints and other inhomogenities. This paper addresses the effect of an open joint on stress wave transmission. An elastodynamic analysis is developed to supplement and explain some recent observations by Fourney and Dick(1995) on open as well as filled joints. The analytical model developed here assuming spherical symmetry can be extended to filled joints between dissimilar media, but results are presented only for open joints separating identical materials. As a special case, stress wave transmission across a joint with no gap is also addressed.

Elasto-plastic contact stress analysis of joints subjected to cyclic loading

Rigorous elastic-plastic finite element analysis of joints subjected to cyclic loading is carried out. An incremental-iterative algorithm is developed in a modular form combining elasto-plastic material behaviour and contact stress analysis. For the case of the interference fit, the analysis sequentially carries out insertion of the pin and application of the load on the joint, covering possible initiation of separation (and/or yielding) and progressively the receding/advancing contact at the pin-plate interface. Deformations of both the plate and the pin are considered in the analysis. Numerical examples are presented for the case of an interference fit pin in a large plate under remote cyclic tension, and for an interference fit pin lug joint subjected to cyclic loading. A detailed study is carried out for the latter problem considering the effect of change in contact/separation at the pin-plate interface on local stresses, strains and redistribution of these stresses with the spread of a plastic zone. The results of the study are a useful input for the estimation of the fatigue life of joints. Copyright (C) 1996 Elsevier Science Ltd

Influence of strain rate and state-of-stress on the formation of ferrite in stainless steel type AISI 304 during hot working

The influence of strain rate and state-of-stress on the formation of ferrite in stainless steel type AISI 304L, 304 and 304 as-cast, during hot working has been studied. Compression and torsion tests were conducted in the temperature range 1100 to 1250 degrees C and strain rate range 0.001 to 100 s(-1) on these materials, Ferrite formation occurs during deformation at temperatures above 1150 degrees C and strain rates above 10 s(-1), in stainless steel type AISI 304L and 304. The tendency for the formation of ferrite is more in as-cast 304 than in wrought 304, In as-cast 304 the ferrite forms at lower temperatures and strain rates, The tendency for the ferrite formation is more in torsion than in compression.

Glutathione peroxidase3 of Saccharomyces cerevisiae protects phospholipids during cadmium-induced oxidative stress

The present study was undertaken to determine the role of glutathione peroxidase3 (gpx3) in phospholipid protection in cells. Wild-type (WT) cells showed an overall increase in phospholipids upon 50 mu M cadmium (Cd)-treatment, whereas an untreated gpx3 Delta strain showed a drastic reduction in overall phospholipids which was further reduced with 50 mu M Cd. In WT cells, Cd-exposure increased the short chain fatty acids and decreased the unsaturated fatty acids and the magnitude was high in Cd-treated gpx3 Delta cells. Purified recombinant gpx3p showed higher activity with phospholipid hydroperoxides than shorter hydroperoxides. An increase in gpx activity was observed in Cd-treated WT cells and no such alteration was observed in gpx3 Delta. WT cells treated with Cd showed an increase in MDA over untreated, while untreated gpx3 Delta cells themselves showed a higher level of MDA which was further enhanced with Cd-treatment. Iron, zinc and calcium levels were significantly altered in WT and gpx3 Delta cells during Cd-treatment.

Thermodynamics of salt roasting of sulphide ores

Thermodynamic analysis of a non-polluting process for the effective treatment of lean multimetallic sulphide ores is presented. The sulphide ore is roasted with sodium chloride in air. Metal sulphides are converted to chlorides that can be separated from the unaffected gangue material. At a temperature of 1100 K the chlorides are present both in gaseous and in condensed states. Volatile chlorides can be easily removed and subsequently condensed. The chlorides present in the condensed state can be leached to separate them from the gangue. The sulphur is trapped as Na2SO4 and thus SO2 emission is minimized. Ellingham diagrams are used to compare data for a large number of elements. The major thermodynamic driving force is provided by the higher stability of Na2SO4 relative to NaCl.