Two-Phase Metallic Thermal Interface Materials Processed Through Liquid Phase Sintering Followed by Accumulative Roll Bonding

Thermal interface materials (TIMs) form a mechanical and thermal link between a heat source and a heat sink. Thus, they should have high thermal conductivity and high compliance to efficiently transfer heat and accommodate any differential strain between the heat source and the sink, respectively. This paper reports on the processing and the characterization of potential metallic TIM composite solders comprising of Cu, a high conductivity phase, uniformly embedded in In matrix, a highly compliant phase. We propose the fabrication of such a material by a two-step fabrication technique comprising of liquid phase sintering (LPS) followed by accumulative roll bonding (ARB). To demonstrate the efficacy of the employed two-step processing technique, an In-40 vol. % Cu composite solder was produced first using LPS with short sintering periods (30 or 60 s at 160 degrees C) followed by ARB up to five passes, each pass imposing a strain of 50%. Mechanical response and electrical and thermal conductivities of the fabricated samples were evaluated. It was observed that processing through ARB homogenizes the distribution of Cu in an In matrix, disintegrates the agglomerates of Cu powders, and also significantly increases thermal and electrical conductivities, almost attaining theoretically predicted values, without significantly increasing the flow stress. Furthermore, the processing technique also allows the insertion of desired foreign species, such as reduced graphene oxide, in In-Cu for further enhancing a target property, such as electrical conductivity.

Optical-Phonon-Limited High-Field Transport in Layered Materials

An optical-phonon-limited velocity model has been employed to investigate high-field transport in a selection of layered 2-D materials for both, low-power logic switches with scaled supply voltages, and high-power, high-frequency transistors. Drain currents, effective electron velocities, and intrinsic cutoff frequencies as a function of carrier density have been predicted, thus providing a benchmark for the optical-phonon-limited high-field performance limits of these materials. The optical-phonon-limited carrier velocities for a selection of multi-layers of transition metal dichalcogenides and black phosphorus are found to be modest compared to their n-channel silicon counterparts, questioning the utility of biasing these devices in the source-injection dominated regime. h-BN, at the other end of the spectrum, is shown to be a very promising material for high-frequency, high-power devices, subject to the experimental realization of high carrier densities, primarily due to its large optical-phonon energy. Experimentally extracted saturation velocities from few-layer MoS2 devices show reasonable qualitative and quantitative agreement with the predicted values. The temperature dependence of the measured v(sat) is discussed and compared with the theoretically predicted dependence over a range of temperatures.

Influence of the upwelling events on the delta C-13 and delta O-18 of the benthic bivalve shells of the South Western Continental Margin of India

In this study, the influence of the spatial and temporal variability of upwelling intensity and the associated biological productivity observed during different phases of summer monsoon along the southwestern continental margin of India (SWCMI) on the delta C-13 and delta O-18 of the inorganic biogenic carbonate shells was investigated. Multispecies benthic bivalve shells (1-5 mm) separated from ten surface sediment samples of SWCMI (off 12 degrees N, 10 degrees N and 9 degrees N) collected during the onset (OSM) and peak (PSM) phase of the summer monsoon of 2009 were analysed for delta C-13 and delta O-18. Sea surface temperature along the study region indicates prominent upwelling in PSM than in OSM. A comparison of analytical and predicted values for delta O-18 in the bivalve shells confirmed their in situ origin during both the sampling periods. During PSM, the delta C-13 values in the benthic bivalve shells were more depleted in C-13 than during OSM which recorded lower values of delta C-13 in dissolved inorganic carbon of bottom waters expected in the study region in PSM due to the upwelled waters, high surface productivity and the associated high degradation of the organic matter in the subsurface and bottom waters. However, this depletion of delta C-13 was not observed in benthic bivalve shells obtained from 10 degrees N, since it is influenced by high export fluxes of carbon from the Cochin estuary since early monsoon months.