Kinetics of oxidation of copper sulfide

The oxidation rate of a cuprous sulfide pellet suspended in a stream of air was followed by measuring the evolution of SO2 titrimetrically. Thin thermocouples embedded in the center of the sample recorded the variation of temperature during oxidation. The reaction was found to be topochemical and the sample temperature was found to be higher than its surroundings initially for about half an hour. After this initial period, the sample temperature decreased to that of the surroundings and remained constant during the rest of the period of over 5 hr. The apparent activation energy from the experimental data was found to be different for the initial (nonisothermal) and subsequent (isothermal) periods. Rate controlling mechanisms for these two intervals have been proposed based on interface chemical reaction, mass transfer resistance, and heat transfer concepts. Fair agreement is found between the theoretical rates based on transport mechanisms and those obtained experimentally

Infrared spectra of trichloroacetates of copper, calcium, strontium and barium

Infrared spectra of trichloroacetates of Cu, Ca, Sr and Ba were studied in order to investigate the effect of coordination on the vibration spectra of the ligand. The shifts of the antisymmetric and symmetric COO- stretching frequencies are explained on the basis of the type of co-ordination of the COO- group to the metal ion. From the spectra it is established that the coordination of the COO- group to metal is different for trichloroacetates and monochloroacetates.

Polarographic and redox potential studies on copper(I) and copper(II) and their complexes. Part III. Copper (I and II)-ethylene diamine and edta complexes and theory of formation of step reduction waves in cupric copper systems

Polarographic and redox potential measurements on the cupric and cuprous complexes of ethylenediamine and EDTA have been carried out. From the ratio of the stability constants of the cupric and cuprous complexes, and the stability constant of the cupric complex, the stability constant of the cuprous-ethylenediamine complex is obtained. In the case of the EDTA complex it has been possible to obtain only βic/β2ous from the equilibrium concentrations of the cuprous and cupric complexes and the disproportionation constant. The inequalities for the appearance of step reduction waves have been given. The values of the stability constants of the cupric and cuprous complexes determined by the polarographic-redox potential method have been used to explain the appearance of step reduction waves in some systems and the non-appearance in other systems.

Method for obtaining minimum noise in a general purpose hot wire amplifier

It has been shown that the conventional practice of designing a compensated hot wire amplifier with a fixed ceiling to floor ratio results in considerable and unnecessary increase in noise level at compensation settings other than optimum (which is at the maximum compensation at the highest frequency of interest). The optimum ceiling to floor ratio has been estimated to be between 1.5-2.0 ωmaxM. Application of the above considerations to an amplifier in which the ceiling to floor ratio is optimized at each compensation setting (for a given amplifier band-width), shows the usefulness of the method in improving the signal to noise ratio.

Polarographic and redox potential studies on copper(I) and copper(II) and their complexes. Part I. Copper(I and II)-ammonia and methylamine complexes

The equilibrium between cuprous ion, cupric ion and metallic copper has been studied using polarographic and redox potential measurements, by reducing cupric ion with copper gauze until equilibrium. Using the well-defined anodic diffusion current plateau, an amperometric method for estimating cuprous copper based on the titration of cuprous ion with dichromate or permanganate has been developed. The diffusion current constant and the disproportionation constant of cuprous ion and the standard potential for the reduction reaction of Cu2+ → Cu+ have been determined. Polarograms have been taken after reducing cupric complexes of ammonia and methylamine with copper until equilibrium. In the case of the copper-ammonia system, reduction to the cuprous state is practically complete while in the case of the cupric-methylamine system, the first cathodic wave occurs to some extent. A new method, called the polarographic-redox potential method, for determining the stability constants of cuprous and cupric complexes has been developed. The method depends upon the determination of the concentration of complexes by polarographic wave heights, and free cupric anc cuprous ions by redox potentials. The stability constants of the following complexes have been obtained: Cu(NH3)2+4, Cu(NH3)+2, Cu(CH3NH2)2(OH)2, Cu(CH3NH2)+2. The stability constants determined by the new method and the half-wave potential shift method agree and the value for the cupric-ammonia complex is in good agreement with Bjerrum method, indicating the reliability of this method.

Spectrophotometric determination of copper with piperidinium piperidyl dithioformate

The reagent piperidinium piperidyl dithioformate forms with copper in aqueous solution a yellowish brown complex which can be extracted with carbon tetrachloride. The copper-PPDF complex in carbon tetrachloride solution has maximum absorption at 434 nm. A spectrophotometric method for determining copper has been developed as the reagent has been shown to form a definite complex.

Spectrophotometric and potentiometric investigations of copper (II)-Ethanolamine complexes - Part III. diethanolamine (Gaussian analysis of electronic spectra in mono and diethanolamine systems)

Spectrophotometric and potentiometric investigations have been carried out on copper-diethanolamine system. Job plots at 900, 900 and 580 mμ have indicated the formation of CuD++, CuD2++ and CuD3++. The n- pA curves obtained indicate the formation of CuD++, CuD2++, CuD3++, CuDOH+, CuD2OH+ and CuD3OH+. The n- pA curves have been analyzed to obtain the stability constants of these complexes. Absorption curves of pure complexes have been computed by a graphical method. Gaussian analysis of the absorption curves of pure and hydroxy complexes show the presence of a second band, indicating that the structure is that of a distorted octahedron.

Raman and infrared spectra of copper formate tetrahydrate

The Raman and i.r. spectra of antiferroelectric copper formate tetrahydrate have been recorded. The i.r. spectrum of copper formate tetrahydrate at liquid air temperature (the phase transition is at −38·9°C) does not show any striking changes from the room temperature spectrum except for intensity variations. This is explained as due to the fact that the frequency of reorientation of the protons even in the paraelectric phase is much less than the optical frequencies.

Synthesis, characterisation and thermal analysis of copper (II) and chromium (II, III) hydrazine carboxylates

Copper(II) hydrazine carboxylate monohydrate, Cu(N2H3COO)2·H2O and chromium (II, III) hydrazine carboxylate hydrates, Cu(N2H3COO)2·H2O and Cu(N2H3COO)2·3H2O have been prepared and characterised by chemical analysis, IR, visible spectra and magnetic measurements. Thermal analysis of the copper complex yields a mixture of copper metal and copper oxide. Chromium complexes on thermal decomposition yield Cr2O3 as residue. Decomposition of chromium(HI) complex under hydrothermal conditions yield CrOOH, a precursor to CrO2.

Effect of copper addition on the fracture and fatigue crack growth behavior of solution heat-treated SUS 304H austenitic steel

Small additions of Cu to the SUS 304H, a high temperature austenitic stainless steel, enhance its high temperature strength and creep resistance. As Cu is known to cause embrittlement, the effect of Cu on room temperature mechanical properties that include fracture toughness and fatigue crack threshold of as-solutionized SUS 304H steel were investigated in this work. Experimental results show a linear reduction in yield and ultimate strengths with Cu addition of up to 5 wt.% while ductility drops markedly for 5 wt.% Cu alloy. However, the fracture toughness and the threshold stress intensity factor range for fatigue crack initiation were found to be nearly invariant with Cu addition. This is because the fracture in this alloy is controlled by the debonding from the matrix of chromium carbide precipitates, as evident from fractography. Cu, on the other hand, remains either in solution or as nano-precipitates and hence does not influence the fracture characteristics. It is concluded that small additions of Cu to 304H will not have adverse effects on its fracture and fatigue behavior. (C) 2010 Elsevier B.V. All rights reserved.

Oxygen chemistry in copper oxides: evidence for O− species

Core-level spectroscopic studies suggest that cuprates nominally supposed to contain Cu3+ions are likely to have the excess positive charge on oxygen instead, giving rise to O-type species (oxygen holes)