Design of a Near Optimum Regulator for a Power Plant

For systems which can be decomposed into slow and fast subsystems, a near optimum linear state regulator consisting of two subsystem regulators can be developed. Depending upon the desired criteria, either a short term (fast controller) or a long term controller (slow controller) can be easily designed with minimum computational costs. Using this approach an example of a power system supplying a cyclic load is studied and the performance of the different controllers are compared.

Ternary adder and subtracter using ternary multiplexer

This paper describes the use of a ternary multiplexer as a building block in the implementation of ternary adders and subtractors and also in the development of ternary coded adders/subtractors.

Chemical changes during the aging and decomposition of composite solid propellants

During the thermal decomposition of orthorhombic ammonium perchlorate (AP) at 230°C, where the decomposition is only up to 30 wt %, there is an accumulation in the solid of acids, the concentration of which increases up to 15% decomposition, after which it decreases till it reaches the original value. Similar observations have been made in the polystyrene (PS)/AP propellant systems. Aging studies of PS/AP propellants have been carried out earlier [1], where it has been shown that for the aged propellants the thermal decomposition (TD) rate at 230°C and 260°C and ambient pressure burning rate (Image ) both increase and this increase is due to the formation of reactive intermediate “polystyrene peroxide (PSP).” In the present studies it has been observed that during the aging of the propellant at 150°C, the acid is formed and gets accumulated in the propellant, which may also be responsible for the increase in TD rate and perhaps may be more effective than PSP.

Studies On Diglycine Sulfate

The dielectric measurements on diglycine sulphate in the temperature range 5-400 K, show that it is a normal dielectric, unlike triglycine sulphate which is a ferroelectric. The difference in the dielectric behavior of these two glycine sulphates has been explained on the basis of certain structural features derived from a study of their vibration spectra.

Complexes of Lanthanide Perchlorates with N-(2-Pyrimidyl)benzamide

New complexes of lanthanide perchlorates with N-(2-pyrimidyl)benzamide (BApymH) of the general formulae [Ln(BApymH)4](ClO4)3 (where Ln = La-Yb and Y) have been synthesised and characterised by chemical analysis, molar conductivity and physical methods such as infrared and electronic spectra in the visible region. Molar conductance and infrared data point to the ionic nature of the per-chlorate groups in the complexes. IR data unequivocally proves that the coordination of the ligand to the metal ion takes place in a bidentate fashion through the oxygen of the secondary amide and nitrogen of the pyrimidine ring. From a comparison of the visible electronic spectral shapes of the Nd3+ and Ho3+ complexes with those reported in the literature, an eight coordinate geometry around the metal ion has tentatively been assigned in all the complexes.

Implementation of a hybrid PCM encoding scheme

An improved encoding scheme is proposed wherein the quantizer step size incorporates both instantaneous and syllabic adaptation. The information needed to carry out this adaptation is extracted at the coder after the D/A conversion of the digital output, so that the coder and the decoder track each other. A 5-bit coder has been designed and built which has a dynamic range of 38 dB with a constant SNR of 30 dB, and the quality of its output signal is found to be comparable to that of other coding schemes

A Monte Carlo study of crystal structure transformations

The Metropolis algorithm has been generalized to allow for the variation of shape and size of the MC cell. A calculation using different potentials illustrates how the generalized method can be used for the study of crystal structure transformations. A restricted MC integration in the nine dimensional space of the cell components also leads to the stable structure for the Lennard-Jones potential.

Purification of Antibodies Specific to a Dinucleotide Using the Hapten Bound to Deae Cellulose as an Affinity Column

The dinucleotide dpTpA held electrostatically on DEAE cellulose was used as an affinity column for the purification of dpTpA specific antibodies. Chromatography of the y-globulin fraction from dpTpA specific antisera on this column resulted in the retention of dpTpA specific antibodies which were later eluted along with the bound dpTpA using 1M NaC1. Dextran coated charcoal was the method of choice for the dissociation and removal of dpTpA bound to the antibodies. This method may extend itself to the purification of antibodies specific for other oligonucleotides.

Probabilistic Seismic Design of Pile Foundations in Non Liquefiable Soil by Response Spectrum Approach

The behavior of pile foundations in non liquefiable soil under seismic loading is considerably influenced by the variability in the soil and seismic design parameters. Hence, probabilistic models for the assessment of seismic pile design are necessary. Deformation of pile foundation in non liquefiable soil is dominated by inertial force from superstructure. The present study considers a pseudo-static approach based on code specified design response spectra. The response of the pile is determined by equivalent cantilever approach. The soil medium is modeled as a one-dimensional random field along the depth. The variability associated with undrained shear strength, design response spectrum ordinate, and superstructure mass is taken into consideration. Monte Carlo simulation technique is adopted to determine the probability of failure and reliability indices based on pile failure modes, namely exceedance of lateral displacement limit and moment capacity. A reliability-based design approach for the free head pile under seismic force is suggested that enables a rational choice of pile design parameters.

Improving the dynamic range of a CVSD coder

The letter describes a method of improving the dynamic range of a continuously variable slope delta modulator (CVSD). This is achieved by modifying the basic step size delta0 Compared to the CVSD algorithm, the modified CVSD (MCVSD) algorithm yields about 15–20 dB dynamic range improvement without degrading the peak SNR and the bit error rate tolerance.

Laboratory Test Methods For The Evaluation Of Flammability Of Polymers

Combustion is a complex phenomena involving a multiplicity of variables. Some important variables measured in flame tests follow [1]. In order to characterize ignition, such related parameters as ignition time, ease of ignition, flash ignition temperature, and self-ignition temperature are measured. For studying the propagation of the flame, parameters such as distance burned or charred, area of flame spread, time of flame spread, burning rate, charred or melted area, and fire endurance are measured. Smoke characteristics are studied by determining such parameters as specific optical density, maximum specific optical density, time of occurrence of the densities, maximum rate of density increase, visual obscuration time, and smoke obscuration index. In addition to the above variables, there are a number of specific properties of the combustible system which could be measured. These are soot formation, toxicity of combustion gases, heat of combustion, dripping phenomena during the burning of thermoplastics, afterglow, flame intensity, fuel contribution, visual characteristics, limiting oxygen concentration (OI), products of pyrolysis and combustion, and so forth. A multitude of flammability tests measuring one or more of these properties have been developed [2]. Admittedly, no one small scale test is adequate to mimic or assess the performance of a plastic in a real fire situation. The conditions are much too complicated [3, 4]. Some conceptual problems associated with flammability testing of polymers have been reviewed [5, 6].

Combined Use of Solid of Revolution, Thin Shell, and Interphase Elements for Analysis of Cylindrical Shells

Near the boundaries of shells, thin shell theories cannot always provide a satisfactory description of the kinematic situation. This imposes severe limitations on simulating the boundary conditions in theoretical shell models. Here an attempt is made to overcome the above limitation. Three-dimensional theory of elasticity is used near boundaries, while thin shell theory covers the major part of the shell away from the boundaries. Both regions are connected by means of an “interphase element.” This method is used to study typical static stress and natural vibration problems

Metabolism of alpha-terpineol by Pseudomonas incognita

Details of the metabolism of alpha-terpineol by Pseudomonas incognita are presented. Degradation of alpha-terpineol by this organism resulted in the formation of a number of acidic and neutral metabolites. Among the acidic metabolites, beta-isopropyl pimelic acid, 1-hydroxy-4-isopropenyl-cyclohexane-1-carboxylic acid, 8-hydroxycumic acid, oleuropeic acid, cumic acid, and p-isopropenyl benzoic acid have been identified. Neutral metabolites identified were limonene, p-cymene-8-ol, 2-hydroxycineole, and uroterpenol. Cell-free extracts prepared from alpha-terpineol adapted cells were shown to convert alpha-terpineol, p-cymene-8-ol, and limonene to oleuropeic acid, 8-hydroxycumic acid, and perillic acid, respectively, in the presence of NADH. The same cell-free extract contained NAD+ -specific dehydrogenase(s) which converted oleuropyl alcohol, p-cymene-7,8-diol, and perillyl alcohol to their corresponding 7-carboxy acids. On the basis of various metabolites isolated from the culture medium, together with the supporting evidence obtained from enzymatic and growth studies, it appears that P. incognita degrades alpha-terpineol by at least three different routes. While one of the pathways seems to operate via oleuropeic acid, a second may be initiated through the aromatization of alpha-terpineol. The third pathway may involve the formation of limonene from alpha-terpineol and its further metabolism.

Study of Friction and Transfer Layer Formation in Copper-Steel Tribo-System: Role of Surface Texture and Roughness Parameters

In the present investigation, experiments were conducted on a tribological couple-copper pin against steel plate-using an inclined pin-on-plate sliding tester to understand the role of surface texture and roughness parameters of the plate on the coefficient friction and transfer layer formation. Two surface characteristics of the steel plates-roughness and texture-were varied in the tests. It was observed that the transfer layer formation and the coefficient of friction along with its two components, namely, the adhesion and plowing, are controlled by the surface texture of the plate. The plowing component of friction was highest for the surface texture that promotes plane strain conditions while it was lowest for the texture that favors plane stress conditions at the interface. Dimensionless quantifiable roughness parameters were formulated to describe the degree of plowing and hence the plane strain/stress type deformations taking place at the asperity level.

Robustness of the partitions in grouping multi-item inventories

A recent work obtained closed-form solutions to the.problem of optimally grouping a multi-item inventory into subgroups with a common order cycle per group, when the distribution by value of the inventory could be described by a Pareto function. This paper studies the sensitivity of the optimal subgroup boundaries so obtained. Closed-form expressions have been developed to find intervals for the subgroup boundaries for any given level of suboptimality. Graphs have been provided to aid the user in selecting a cost-effective level of aggregation and choosing appropriate subgroup boundaries for a whole range of inventory distributions. The results of sensitivity analyses demonstrate the availability of flexibility in the partition boundaries and the cost-effectiveness of any stock control system through three groups, and thus also provide a theoretical support to the intuitive ABC system of classifying the items.