Monte carlo simulation for molecular gas dynamics

The dynamics of low-density flows is governed by the Boltzmann equation of the kinetic theory of gases. This is a nonlinear integro-differential equation and, in general, numerical methods must be used to obtain its solution. The present paper, after a brief review of Direct Simulation Monte Carlo (DSMC) methods due to Bird, and Belotserkovskii and Yanitskii, studies the details of theDSMC method of Deshpande for mono as well as multicomponent gases. The present method is a statistical particle-in-cell method and is based upon the Kac-Prigogine master equation which reduces to the Boltzmann equation under the hypothesis of molecular chaos. The proposed Markoff model simulating the collisions uses a Poisson distribution for the number of collisions allowed in cells into which the physical space is divided. The model is then extended to a binary mixture of gases and it is shown that it is necessary to perform the collisions in a certain sequence to obtain unbiased simulation.

Study Of The Hvdc-Torsional Interactions Through Digital Dynamic Simulation

This paper presents the detailed dynamic digital simulation for the study of phenomenon of torsional interaction between HVDC-Turbine generator shaft, dynamics using the novel converter model presented in [ 1 ] The system model includes detailed representation of the synchronous generator and the shaft dynamics, the ac and dc network transients. The results of a case study indicate the various factors that influence the torsional interaction.

Numerical simulation of solidification of liquid aluminum alloy flowing on cooling slope

Preparation of semisolid slurry using a cooling slope is increasingly becoming popular, primarily because of the simplicity in design and ease control of the process. In this process, liquid alloy is poured down an inclined surface which is cooled from underneath. The cooling enables partial solidification and the incline provides the necessary shear for producing semisolid slurry. However, the final microstructure of the ingot depends on several process parameters such as cooling rate, incline angle of the cooling slope, length of the slope and initial melt superheat. In this work, a CFD model using volume of fluid (VOF) method for simulating flow along the cooling slope was presented. Equations for conservation of mass, momentum, energy and species were solved to predict hydrodynamic and thermal behavior, in addition to predicting solid fraction distribution and macrosegregation. Solidification was modeled using an enthalpy approach and a volume averaged technique for the different phases. The mushy region was modeled as a multi-layered porous medium consisting of fixed columnar dendrites and mobile equiaxed/fragmented grains. The alloy chosen for the study was aluminum alloy A356, for which adequate experimental data were available in the literature. The effects of two key process parameters, namely the slope angle and the pouring temperature, on temperature distribution, velocity distribution and macrosegregation were also studied.

Complexation of siRNA with Dendrimer: A Molecular Modeling Approach

This paper reports the structural behavior and thermodynamics of the complexation of siRNA with poly(amidoamine) (PAMAM) dendrimers of generation 3 (G3) and 4 (G4) through fully atomistic molecular dynamics (MD) simulations accompanied by free energy calculations and inherent structure determination. We have also done simulation with one siRNA and two dendrimers (2 x G3 or 2xG4) to get the microscopic picture of various binding modes. Our simulation results reveal the formation of stable siRNA-dendrimer complex over nanosecond time scale. With the increase in dendrimcr generation, the charge ratio increases and hence the binding energy between siRNA and dendrimer also increases in accordance with available experimental measurements. Calculated radial distribution functions of amines groups of various subgenerations in a given generation of dendrimer and phosphate in backbone of siRNA reveals that one dendrimer of generation 4 shows better binding with siRNA almost wrapping the dendrimer when compared to the binding with lower generation dendrimer like G3. In contrast, two dendrimers of generation 4 show binding without siRNA wrapping the den-rimer because of repulsion between two dendrimers. The counterion distribution around the complex and the water molecules in the hydration shell of siRNA give microscopic picture of the binding dynamics. We see a clear correlation between water. counterions motions and the complexation i.e. the water molecules and counterions which condensed around siRNA are moved away from the siRNA backbone when dendrimer start binding to the siRNA back hone. As siRNA wraps/bind to the dendrimer counterions originally condensed onto siRNA (Na-1) and dendrimer (Cl-) get released. We give a quantitative estimate of the entropy of counterions and show that there is gain in entropy due to counterions release during the complexation. Furthermore, the free energy of complexation of IG3 and IG4 at two different salt concentrations shows that increase in salt concentration leads to the weakening of the binding affinity of siRNA and dendrimer.

On the holographic simulation of non-circular zone plates

New methods involving the manipulation of fundamental wavefronts (e.g., plane and spherical) with simple optical components such as pinholes and spherical lenses have been developed for the fabrication of elliptic, hyperbolic and conical holographic zone plates. Also parabolic zone plates by holographic techniques have been obtained for the first time. The performance behaviour of these zone plates has been studied. Further a phenomenological explanation is offered for the observed improved fringe contrast obtained with a spherical reference wave.

Large Eddy Simulation

Large eddy simulation (LES) is an emerging technique for obtaining an approximation to turbulent flow fields It is an improvement over the widely prevalent practice of obtaining means of turbulent flows when the flow has large scale, low frequency, unsteadiness An introduction to the method, its general formulation, and the more common modelling for flows without reaction, is discussed Some attempts at extension to flows with combustion have been made Examples from present work for flows with and without combustion are given The final example of the LES of the combustor of a helicopter engine illustrates the state-of-the-art in application of the technique

Analytical and simulation studies of a multiprocessor system for high-speed numerical computations

This paper describes the architecture of a multiprocessor system which we call the Broadcast Cube System (BCS) for solving important computation intensive problems such as systems of linear algebraic equations and Partial Differential Equations (PDEs), and highlights its features. Further, this paper presents an analytical performance study of the BCS, and it describes the main details of the design and implementation of the simulator for the BCS.

Structure of the Indian southwesterly pre-monsoon and monsoon boundary layers: Observations and numerical simulation

Characteristics of pre-monsoon and monsoon boundary layer structure and turbulence were studied in New Delhi and Bangalore, India during the summer of 1987. Micrometeorological towers were installed and instrumented at these locations to provide mean and turbulent surface layer measurements, while information on the vertical structure of the atmosphere was obtained using miniradiosondes. Thermal structures of the pre-monsoon and monsoon boundary layers were quite distinct. The daytime, pre-monsoon boundary layer observed over New Delhi was much deeper than that of the monsoon boundary layer observed over Bangalore and at times was characterized by multiple inversions. Surface, turbulent sensible heat fluxes at both sites were approximately the same (235 and 200 Wm−2 for New Delhi and Bangalore, respectively). Diurnal variations in the monsoon boundary layer at Bangalore were more regular compared to those under pre-monsoon conditions at New Delhi. One-dimensional numerical simulations of the pre-monsoon boundary layer using a turbulent energy closure scheme show good agreement with observations.

A Numerical-Simulation Of The Gneiss-Charnockite Transformations In Southern India

This paper presents a numerical simulation of the well-documented, fluid-controlled Kabbal and Ponmudi type gneiss-chamockite transformations in southern India using a free energy minimization method. The computations have considered all the major solid phases and important fluid species in the rock - C-O-H and rock - C-O-H-N systems. Appropriate activity-composition relations for the solid solutions and equations of state for the fluids have been included in order to evaluate the mineral-fluid equilibria attending the incipient chamockite development in the gneisses. The C-O-H fluid speciation pattern in both the Kabbal and Ponmudi type systems indicates that CO2 and H2O make up the bulk of the fluid phase with CO, CH4, H-2 and O2 as minor constituents. In the graphite-buffered Ponmudi-system, the abundance of CO, CH4 and H-2 is orders of magnitude higher than that in the graphite-free Kabbal system. Simulation with C-O-H-N fluids of varying composition demonstrates the complementary role of CO2 and N2 as rather inert dilutants of H2O in the fluid phase. The simulation, carried out on available whole-rock data, has demonstrated the dependence of the transformation X(H2O) on P,T, and phase and chemical composition of the precursor gneiss.

Cell-dynamical simulation of magnetic hysteresis in the two-dimensional Ising system

We present results from numerical simulations using a ‘‘cell-dynamical system’’ to obtain solutions to the time-dependent Ginzburg-Landau equation for a scalar, two-dimensional (2D), (Φ2)2 model in the presence of a sinusoidal external magnetic field. Our results confirm a recent scaling law proposed by Rao, Krishnamurthy, and Pandit [Phys. Rev. B 42, 856 (1990)], and are also in excellent agreement with recent Monte Carlo simulations of hysteretic behavior of 2D Ising spins by Lo and Pelcovits [Phys. Rev. A 42, 7471 (1990)].

Influence of Die Surface Textures during Metal Forming-A Study Using Experiments and Simulation

Friction plays an important role in metal forming processes, and the surface texture of the die is a major factor that influences friction. In the present investigation, experiments were conducted to understand the role of surface texture of the harder die surface and load on coefficient of friction. The data analysis showed that the coefficient of friction is highly dependent on the surface texture of the die surface. Assigning different magnitude of coefficients of friction, obtained in the experiments, at different regions between the die and the workpiece, Finite element (FE) simulation of a compression test was carried out to understand the effect of friction on deformation and stress/strain-rate distribution. Simulation results revealed that, owing to the difference in coefficient of friction, there is a change in metal flow pattern. Both experimental and simulation results confirmed that the surface texture of the die surface and thus coefficient of friction directly affects the strain rate and flow pattern of the workpiece.

Relaxation system based sub-grid scale modelling for large eddy simulation of Burgers' equation

An implicit sub-grid scale model for large eddy simulation is presented by utilising the concept of a relaxation system for one dimensional Burgers' equation in a novel way. The Burgers' equation is solved for three different unsteady flow situations by varying the ratio of relaxation parameter (epsilon) to time step. The coarse mesh results obtained with a relaxation scheme are compared with the filtered DNS solution of the same problem on a fine mesh using a fourth-order CWENO discretisation in space and third-order TVD Runge-Kutta discretisation in time. The numerical solutions obtained through the relaxation system have the same order of accuracy in space and time and they closely match with the filtered DNS solutions.

Solvation dynamics in a Brownian dipolar lattice. Comparison between computer simulation and various molecular theories of solvation dynamics

Several recent theoretical and computer simulation studies have considered solvation dynamics in a Brownian dipolar lattice which provides a simple model solvent for which detailed calculations can be carried out. In this article a fully microscopic calculation of the solvation dynamics of an ion in a Brownian dipolar lattice is presented. The calculation is based on the non‐Markovian molecular hydrodynamic theory developed recently. The main assumption of the present calculation is that the two‐particle orientational correlation functions of the solid can be replaced by those of the liquid state. It is shown that such a calculation provides an excellent agreement with the computer simulation results. More importantly, the present calculations clearly demonstrate that the frequency‐dependent dielectric friction plays an important role in the long time decay of the solvation time correlation function. We also find that the present calculation provides somewhat better agreement than either the dynamic mean spherical approximation (DMSA) or the Fried–Mukamel theory which use the simulated frequency‐dependent dielectric function. It is found that the dissipative kernels used in the molecular hydrodynamic approach and in the Fried–Mukamel theory are vastly different, especially at short times. However, in spite of this disagreement, the two theories still lead to comparable results in good agreement with computer simulation, which suggests that even a semiquantitatively accurate dissipative kernel may be sufficient to obtain a reliable solvation time correlation function. A new wave vector and frequency‐dependent dissipative kernel (or memory function) is proposed which correctly goes over to the appropriate expressions in both the single particle and the collective limits. This form is expected to lead to better results than all the existing descriptions.