Bi2W1–xCuxO6–x(0.7[less-than-or-eq]x[less-than-or-eq]0.8): a new oxide-ion conductor

Anion-deficient Aurivillius phases of the general formula, Bi2Wi-xCuxO6-2x, possessing orthorhombic/tetragonal Bi2WO6-like structures, have been synthesized by quenching the oxide melts. The tetragonal phase stabilized for the compositions 0.7 less-than-or-equal-to x less-than-or-equal-to 0.8 is a good oxide-ion conductor in the temperature range 500-900 K, the x = 0.7 composition exhibiting the highest conductivity in the series.

Unsteady three-dimensional boundary layer flow due to a stretching surface

In this numerical study, the unsteady laminar incompressible boundary-layer flow over a continuously stretching surface has been investigated when the velocity of the stretching surface varies arbitrarily with time. Both the nodal and the saddle point regions of flow have been considered for the analysis. Also, constant wall temperature/concentration and constant heat/mass flux at the stretching surface have been taken into account. The quasilinearisation method with an implicit finite-difference scheme is used in the nodal point region (0 less-than-or-equal-to c less-than-or-equal-to 1) where c denotes the stretching ratio. This method fails in the saddle point region (-1 less-than-or-equal-to c less-than-or-equal-to 0) due to the occurrence of reverse flow in the y-component of velocity. In order to overcome this difficulty, the method of parametric differentiation with an implicit finite-difference scheme is used, where the values at c = 0 are taken as starting values. Results have been obtained for the stretching velocities which are accelerating and decelerating with time. Results show that the skin friction, the heat transfer and the mass transfer parameters respond significantly to the time dependent stretching velocities. Suction (A > 0) is found to be an important parameter in obtaining convergent solution in the case of the saddle point region of flow. The Prandtl number and the Schmidt number strongly affect the heat and mass transfer of the diffusing species, respectively.

Inefficient excision of uracil from loop regions of DNA oligomers by E.coli uracil DNA glycosylase

Kinetic parameters for uracil DNA glycosylase (E.coli)-catalysed excision of uracil from DNA oligomers containing dUMP in different structural contexts were determined. Our results show that single-stranded oligonucleotides (unstructured) are used as somewhat better substrates than the double-stranded oligonucleotides. This is mainly because of the favourable V-max value of the enzyme for single-stranded substrates. More interestingly, however, we found that uracil release from loop regions of DNA hairpins is extremely inefficient. The poor efficiency with which uracil is excised from loop regions is a result of both increased K-m and lowered V-max values. This observation may have significant implications in uracil DNA glycosylase-directed repair of DNA segments that can be extruded as hairpins. In addition, these studies are useful in designing oligonucleotides for various applications in DNA research where the use of uracil DNA glycosylase is sought.

Influence of Bi 3+ ions in enhancing the magnitude of positive temperature coefficients of resistance in n-BaTiO3 ceramics

Bi3+ ions substituting at Ba-sites in a limited concentration range with another donor dopant occupying the Ti-sites in polycrystalline BaTiO3 enhanced the positive temperature coefficient of resistance (PTCR) by over seven orders of magnitude. These ceramics did not require normal post sinter annealing or a change to an oxygen atmosphere during annealing. These ceramics had low porosities coupled with better stabilities to large applied electric fields and chemically reducing atmospheres. Bi3+ ions limited the grain growth to less than 8 mum in size, they enhanced the concentration of acceptor-type trap centres at the grain-boundary-layer regions and maintained complete tetragonality at low grain sizes in BaTiO3 ceramics.

Identification of Local Conformational Similarity in Structurally Variable Regions of Homologous Proteins Using Protein Blocks

Structure comparison tools can be used to align related protein structures to identify structurally conserved and variable regions and to infer functional and evolutionary relationships. While the conserved regions often superimpose well, the variable regions appear non superimposable. Differences in homologous protein structures are thought to be due to evolutionary plasticity to accommodate diverged sequences during evolution. One of the kinds of differences between 3-D structures of homologous proteins is rigid body displacement. A glaring example is not well superimposed equivalent regions of homologous proteins corresponding to a-helical conformation with different spatial orientations. In a rigid body superimposition, these regions would appear variable although they may contain local similarity. Also, due to high spatial deviation in the variable region, one-to-one correspondence at the residue level cannot be determined accurately. Another kind of difference is conformational variability and the most common example is topologically equivalent loops of two homologues but with different conformations. In the current study, we present a refined view of the ``structurally variable'' regions which may contain local similarity obscured in global alignment of homologous protein structures. As structural alphabet is able to describe local structures of proteins precisely through Protein Blocks approach, conformational similarity has been identified in a substantial number of `variable' regions in a large data set of protein structural alignments; optimal residue-residue equivalences could be achieved on the basis of Protein Blocks which led to improved local alignments. Also, through an example, we have demonstrated how the additional information on local backbone structures through protein blocks can aid in comparative modeling of a loop region. In addition, understanding on sequence-structure relationships can be enhanced through our approach. This has been illustrated through examples where the equivalent regions in homologous protein structures share sequence similarity to varied extent but do not preserve local structure.

Five-level inverter scheme for an open-end winding induction machine with less number of switches

Higher level of inversion is achieved with a less number of switches in the proposed scheme. The scheme proposes a five-level inverter for an open-end winding induction motor which uses only two DC-link rectifiers of voltage rating of Vdc/4, a neutral-point clamped (NPC) three-level inverter and a two-level inverter. Even though the two-level inverter is connected to the high-voltage side, it is always in square-wave operation. Since the two-level inverter is not switching in a pulse width modulated fashion and the magnitude of switching transient is only half compared to the convention three-level NPC inverter, the switching losses and electromagnetic interference is not so high. The scheme is experimentally verified on a 2.5 kW induction machine.

Star formation in giant extragalactic H II regions

Star formation properties in Giant Extragalactic H II Regions (GEHRs) are investigated using optical photometry and evolutionary population synthesis models. Photometric data in $BVR$ bands and in the emission line of H-alpha are obtained by CCD imaging at Vainu Bappu Observatory, Kavalur. Aperture photometry is performed for 180 GEHRs in galaxies NGC 1365, 1566, 2366, 2903, 2997, 3351, 4303, 4449, 4656 and 5253. Thirty six of these GEHRs having published spectroscopic data are studied for star formation properties. The population synthesis model is constructed based on Maeder's stellar evolutionary and Kurucz stellar atmosphere models, to synthesize observational quantities of embedded clusters in GEHRs. The observed H-alpha luminosity is a measure of the number of massive stars while the contribution to BVR bands is from intermediate mass (5-15 solar mass) stars when the cluster is young and from evolving supergiants when the cluster is old (age >/= 6~Myr). Differential reddening between gas and embedded stars is essential to constrain the dereddened cluster colors within the range of youngest clusters. Obscuring dust closely associated with gas, which is distributed in filaments and clumps, as in the case of 30 Doradus, is the most likely configuration giving rise to net reduction of extinction towards stars. The fraction of the stellar photons escaping the nebula unattenuated is estimated to be 50%. GEHRs are rarely found to be simple systems containing stars from single generation. In the present sample such regions in addition to being older than 3~Myr, have their Lyman continuum luminosity reduced by as much as 60%, compared to the observed $B$ band luminosity for a normal IMF. The missing ionizing photons may be escaping the nebula, leading to the ionization of extra-H II region ionized medium. Co-existence of young (age

A study of over-reflection in Hartmann flow

It is observed that Hartmann flow sustains wave propagation in its centre region for waves whose phase speed is less than the maximum flow speed. Similar to the previous observations it is found that viscous boundary layers around the critical level and at the wall replace the exponential regions and wave sinks required for over-reflection in the inviscid flow. The uniform magnetic field stabilizes the flow for small-wave-number disturbances along thez-direction. Over-reflection is confined to a few ranges of phase speeds for which the two boundary layers are close together rather than widely separated. These ranges correspond exactly to those for which unstable eigenmodes exist. Over-reflection is associated with a wave phase tilt opposite in direction to the shear.

Wind loading over the top portions of tall stacks with and without external landing platforms

The variation of the drag force near the top portions of tall stacks with and without external landing platforms, and with the exit open and closed, has been examined by model studies in a wind tunnel at Reynolds numbers of about 10(5). Pressure measurements on three models of different height to diameter ratios have been supplemented by flow visualisation studies. Observations confirm that when there is no platform, significant load enhancement over the top three to four diameters occurs, due to the high suction caused by the sharp separation of the flow over the top from the rim, in the aft regions of the stack. The enhanced loading is found to be greater if the exit is closed. A platform at the top, of less than twice the exit diameter, further increases the drag force near the top, but a still larger platform at the top, of about three times the exit diameter, decreases the drag force to values less than those much further below, effectively nullifying the enhanced drag force. It was found that such a reduction of the enhanced drag force in the top regions can also be achieved by a smaller platform of 1.1 to 1.3 times the local diameter, located at about three to five diameters below the top.

Cloning And Characterization of Mycobacteriophage-13 Promoters

Restriction fragments of mycobacteriophage 13 DNA capable of initiating transcription have been cloned into a promoter selection vector of Escherichia coli, and selected on the basis of development of resistance to chloramphenicol. The growth pattern of these 'promoter clones' on a concentration gradient of chloramphenicol and the biochemical assays of the chloramphenicol acetyl transferase have permitted the assessment of their relative promoter strengths. DNA sequence analysis revealed significant homology of these promoters to the -35 regions of the mycobacterial- and E. coli promoter consensus, but less so to the - 10 region. Based on the sequence of phage 13 promoters identified here and the reported sequences of mycobacterial promoters, a promoter consensus for mycobacteria has been generated.

Interactions of 3' terminal and 5' terminal regions of physalis mottle virus genomic RNA with its replication complex

Physalis mottle virus (PhMV) belongs to the tymogroup of positive-strand RNA viruses with a genome size of 6 kb. Crude membrane preparations from PhMV-infected Nicotiana glutinosa plants catalyzed the synthesis of PhMV genomic RNA from endogenously bound template. Addition of exogenous genomic RNA enhanced the synthesis which was specifically inhibited by the addition of sense and antisense transcripts corresponding to 3' terminal 242 nucleotides as well as the 5' terminal 458 nucleotides of PhMV genomic RNA while yeast tRNA or ribosomal RNA failed to inhibit the synthesis. This specific inhibition suggested that the 5' and 3' non-coding regions of PhMV RNA might play an important role in viral replication.

Structure of ant assemblages in Western Ghats, India: role of habitat, disturbance and introduced species

1. Habitat fragmentation, anthropogenic disturbance and the introduction of invasive species are factors thought to structure ant assemblages. To understand responses of the ant community to changes in the environment, ants are commonly categorised into functional groups, a scheme developed and based on Australian ants. 2. Behaviourally dominant and aggressive ants of the dominant dolichoderinae functional group have been suggested to structure the ant assemblages in arid and semi-arid habitats of these regions. Given the limited geographical distribution of dominant dolichoderinae, it is crucial to determine the responses of the ant community to changes in the environment in their absence. 3. This study addresses this less studied aspect by considering the associations of ants of Western Ghats, India, with habitat, anthropogenic disturbance and introduced ants. We determined how ant functional groups respond to these factors in this region, where dominant dolichoderines are naturally absent, and whether responses are consistent with predictions derived from the ant functional group scheme. 4. This study provides new information on ant assemblages in a little-studied region. As in other parts of the world, ant assemblages in Western Ghats were strongly influenced by habitat and disturbance, with different functional groups associated with different habitats and levels of disturbance. 5. No functional group showed evidence of being influenced by the abundance of introduced species. In addition, predictions of negative interactions between functional groups were not supported. Our findings suggest that abiotic factors are universal determinants of ant assemblage structure, but that competitive interactions may not be.

Optimization of cold and warm workability in stainless steel type AISI 316L using instability maps

The deformation characteristics of stainless steel type AISI 316L under compression in the temperature range 20 to 600 degrees C and strain rate range 0.001 to 100 s(-1) have been studied with a view to characterizing the flow instabilities occurring in the microstructure. At temperatures lower than 100 degrees C and strain rates higher than 0.1 s(-1), 316L stainless steel exhibits flow localization whereas dynamic strain aging (DSA) occurs at intermediate temperatures and below 1 s(-1). To avoid the above flow instabilities, cold working should be carried out at strain rates less than 0.1 s(-1). Warm working of stainless steel type AISI 316L may be done in the temperature and strain rate regime of: 300 to 400 degrees C and 0.001 s(-1) 300 to 450 degrees C and 0.01 s(-1): 450 to 600 degrees C and 0.1 s(-1); 500 degrees C and 1 s(-1) since these regions are free from flow instabilities like DSA and flow localization. The continuum criterion, developed on the basis of the principles of maximum rate of entropy production and separability of the dissipation function, predicts accurately all the above instability features.

Structure of sesbania mosaic virus at 3 å resolution

Background: Sobemoviruses are a group of RNA plant viruses that have a narrow host range. They are characterized in vitro by their stability, high thermal inactivation point and longevity. The three-dimensional structure of only one virus belonging to this group, southern bean mosaic virus (SBMV), is known. Structural studies on sesbania mosaic virus (SMV), which is closely related to SBMV, will provide details of the molecular interactions that are likely to be important in the stability and assembly of sobemoviruses. Results: We have determined the three-dimensional structure of SMV at 3 Angstrom resolution. The polypeptide fold and quaternary organization are very similar to those of SBMV. The capsid consists of sixty icosahedral asymmetric units, each comprising three copies of a chemically identical coat protein subunit, which are designated as A, B and C and are in structurally different environments. Four cation-binding sites have been located in the icosahedral asymmetric unit. Of these, the site at the quasi-threefold axis is not found in SBMV. Structural differences are observed in loops and regions close to this cation-binding site. Preliminary studies on ethylene diamine tetra acetic acid (EDTA) treated crystals suggest asymmetry in removal of the quasi-equivalent cations at the AB, BC, and AC subunit interfaces. Conclusions: Despite the overall similarity between SMV and SBMV in the nature of the polypeptide fold, these viruses show a number of differences in intermolecular interactions. The polar interactions at the quasi-threefold axis are substantially less in SMV and positively charged residues on the RNA-facing side of the protein and in the N-terminal arm are not particularly well conserved. This suggests that protein-RNA interactions are likely to be different between the two viruses.

Turbulent heat flux variation over the Monsoon-Trough region during MONTBLEX-90

Tower data collected during the Monsoon-Trough Boundary Layer Experiment (MONTBLEX-90) have been analysed to understand the observed structure of the surface layer over an arid region (Jodhpur) and a moist region (Kharagpur) during active and weak phases of the 1990 southwest monsoon. Turbulent heat and momentum fluxes are estimated by the eddy correlation method using sonic data. The turbulent momentum flux at both Jodhpur and Kharagpur was larger when the winds were stronger, reaching a maximum of the order of 0.5 N m(-2) on 5 and 6 August when a low pressure system was located over the region. The heat flux at Jodhpur is high during weak monsoon days, the maximum being 450 W m(-2), whereas during active days the flux never exceeds 200 W m(-2). At Kharagpur, the flux does not vary significantly between active and weak monsoon days, the maximum in either phase being 160 W m(-2) At Jodhpur, there is significant contrast in the near-surface air temperature, being higher during weak monsoon days as compared to active days. Cloud cover did not vary significantly in both the regions. The turbulent heat flux variation at both the sites appears to be correlated mainly with soil mixture, and less sensitive to cloud cover.