Physicochemical studies on the gelation of hen egg yolk; separation of gelling protein components from yolk plasma

A study of the component(s) in egg yolk responsible for gelation of yolk on freezing and thawing has shown that granule-free yolk plasma, obtained by high-speed centrifugation of yolk, has the capacity to gel. As with the whole yolk, gelation of yolk plasma on freezing and thawing could be inhibited by additives such as sugars, sodium chloride, proteolytic enzymes, and phospholipase-A. Phospholipase-C, which induces gelation of whole yolk at room temperature, has a similar effect on yolk plasma. Yolk plasma has been separated into aggregating (gelling) and soluble fractions by delipidation, using formic acid. Each of these fractions consists of three or four protein components, as observed by gel filtration, ultracentrifugation, and agar electrophoresis. The proteins are glycoproteins and contain bound hexoses, hexosamine, and sialic acid. The gelation of yolk has been attributed to the interactions between protein molecules following disruption of lipid-protein bonds.

The protein components of elastoidin

Not all elastoidin samples from different species of sharks show a high content of tryptophan in contrast to one specimen from an unidentified species examined in our earlier study. There may be considerable species-dependent variation in tryptophan content and analytical artefacts may have occurred. Available analyses for tyrosine in different specimens of fibres also suggest the possibility that the variation in tyrosine content is also species-dependent. Elastoidin, from Galeoscerdo cuveir (Tiger Shark) and another unidentified species, on treatment with formic acid yielded three fractions A,B and C. On the basis of analytical data it appears that specimens of elastoidin containing no (or little) tryptophan may yield fraction B through the solubilization of fraction A by formic acid. C fractions from two specimens of fibres were collagenous in nature. C fractions have been further purified in this study by charcoal treatment which removes a tyrosine-rich contaminant, to yield collagens with only approx. 2–4 residues of tyrosine per assumed mol. wt. of 360000. In the collagen from the unidentified species glucose and galactose were present in the ratio of 2:5; some glucosamine was also present.

Anthranilic acid oxidase system of Tecoma stans—II. : Studies on the properties of a purified anthranilic acid oxidase system and its separation into different enzymic components

An enzyme system which catalysed the conversion of anthranilic acid to catechol has been purified 20-fold from a cell-free leaf extract of Tecoma stans. The optimum substrate concentration was 10−3 M and optimum temperature for the reaction was 45°. The presence of a multi-enzyme system was inferred from inhibition studies. The formation of catechol was inhibited by Mg2+, Zn2+, and Co2+ ions, whereas anthranilic acid disappearance was not affected to the same extent. The effect of metal chelating agents like EDTA, cyanide and pyrophosphate showed a similar trend. PCMB inhibited catechol formation but had no effect on anthranilic acid disappearance. The reaction was not inhibited by catalase, nor was it activated by peroxide-donating systems. This ruled out the possibility of peroxidative type of reaction. The overall reaction is markedly activated by NADPH and THFA. This multi-enzyme was separated into three different components, by fractionation with Alumina Cγ and calcium phosphate gels. The overall reaction catalysed by these components can be represented as anthranilic acid→3-hydroxy anthranilic acid→o-aminophenol→catechol.

Experimental studies on the wear of engine components

Wear studies of engine components of high-speed diesel engines running under various operating conditions are presented. Tests were conducted under controlled conditions over long periods. The results of the various tests are discussed and attempts have been made to examine the effects of engine operating variables and the quality of the lubricating oil on the wear of engine components.

Design of a FIR filter for image restoration using principal component neural networks

The neural network finds its application in many image denoising applications because of its inherent characteristics such as nonlinear mapping and self-adaptiveness. The design of filters largely depends on the a-priori knowledge about the type of noise. Due to this, standard filters are application and image specific. Widely used filtering algorithms reduce noisy artifacts by smoothing. However, this operation normally results in smoothing of the edges as well. On the other hand, sharpening filters enhance the high frequency details making the image non-smooth. An integrated general approach to design a finite impulse response filter based on principal component neural network (PCNN) is proposed in this study for image filtering, optimized in the sense of visual inspection and error metric. This algorithm exploits the inter-pixel correlation by iteratively updating the filter coefficients using PCNN. This algorithm performs optimal smoothing of the noisy image by preserving high and low frequency features. Evaluation results show that the proposed filter is robust under various noise distributions. Further, the number of unknown parameters is very few and most of these parameters are adaptively obtained from the processed image.

Laminar compressible boundary layer flow at a three-dimensional stagnation point with vectored mass transfer

The effect of surface mass transfer velocities having normal, principal and transverse direction components (�vectored� suction and injection) on the steady, laminar, compressible boundary layer at a three-dimensional stagnation point has been investigated both for nodal and saddle points of attachment. The similarity solutions of the boundary layer equations were obtained numerically by the method of parametric differentiation. The principal and transverse direction surface mass transfer velocities significantly affect the skin friction (both in the principal and transverse directions) and the heat transfer. Also the inadequacy of assuming a linear viscosity-temperature relation at low-wall temperatures is shown.

Analysis of conjugate laminar mixed convection cooling in a shrouded array of electronic components

The temperature variation in the insulation around an electronic component, mounted on a horizontal circuit board is studied numerically. The flow is assumed to be laminar and fully developed. The effect of mixed convection and two different types of insulation are considered. The mass, momentum and energy conservation equations in the fluid and conduction equation in the insulation are solved using the SIMPLER algorithm. Computations are carried out for liquid Freon and water, for different conductivity ratios, and different Rayleigh numbers. It is demonstrated that the temperature variation within the insulation becomes important when the thermal conductivity of the insulation is less than ten times the thermal conductivity of the cooling medium.

Erosion and cavity characteristics in rotating components

An investigation of the initiation and growth of erosion and of the effect of velocity and pressure on erosion in a rotating disk is presented. Also, the role of an intervening noncavitating period on erosion is studied. The results indicate that at high intensities the peak rate of erosion decreases with increases in pressure. The erosion rate/time curves obtained for metallic materials are explained by the eroded particle distribution and the cavity size. The average size of the eroded particles decreased when pressure and tensile strength of the material were increased. The erosion rate peaked after an intervening noncavitating period. The use of the rate of erosion, defined as an average over the entire test duration, in the equation governing the theory of erosion resulted in reasonably good correlations. The correlations reveal that it is possible to predict the length, width, and area of a cavity when the cavitation parameter σ is known. The normalized width of a cavity may be estimated if its normalized length is known.

The shear dynamo problem for small magnetic Reynolds numbers

We study large-scale kinematic dynamo action due to turbulence in the presence of a linear shear flow in the low-conductivity limit. Our treatment is non-perturbative in the shear strength and makes systematic use of both the shearing coordinate transformation and the Galilean invariance of the linear shear flow. The velocity fluctuations are assumed to have low magnetic Reynolds number (Re-m), but could have arbitrary fluid Reynolds number. The equation for the magnetic fluctuations is expanded perturbatively in the small quantity, Re-m. Our principal results are as follows: (i) the magnetic fluctuations are determined to the lowest order in Rem by explicit calculation of the resistive Green's function for the linear shear flow; (ii) the mean electromotive force is then calculated and an integro-differential equation is derived for the time evolution of the mean magnetic field. In this equation, velocity fluctuations contribute to two different kinds of terms, the 'C' and 'D' terms, respectively, in which first and second spatial derivatives of the mean magnetic field, respectively, appear inside the space-time integrals; (iii) the contribution of the D term is such that its contribution to the time evolution of the cross-shear components of the mean field does not depend on any other components except itself. Therefore, to the lowest order in Re-m, but to all orders in the shear strength, the D term cannot give rise to a shear-current-assisted dynamo effect; (iv) casting the integro-differential equation in Fourier space, we show that the normal modes of the theory are a set of shearing waves, labelled by their sheared wavevectors; (v) the integral kernels are expressed in terms of the velocity-spectrum tensor, which is the fundamental dynamical quantity that needs to be specified to complete the integro-differential equation description of the time evolution of the mean magnetic field; (vi) the C term couples different components of the mean magnetic field, so they can, in principle, give rise to a shear-current-type effect. We discuss the application to a slowly varying magnetic field, where it can be shown that forced non-helical velocity dynamics at low fluid Reynolds number does not result in a shear-current-assisted dynamo effect.

Nestedness pattern in stream diatom assemblages of central Western Ghats

Community diversity and the population abundance of a particular group of species are controlled by immediate environment, inter-and intra-species interactions, landscape conditions, historical events and evolutionary processes. Nestedness is a measure of order in an ecological system, referring to the order in which the number of species is related to area or other factors. In this study we have studied the nestedness pattern in stream diatom assemblages in 24 stream sites of central Western Ghats, and report 98 taxa from the streams of central Western Ghats region. The communities show highly significant nested pattern. The Mantel test of matrix revealed a strong relationship between species assemblages and environmental conditions at the sites. A significant relationship between species assemblage and environmental condition was observed. Principal component analysis (PCA) indicated that environmental conditions differed markedly across the sampling sites, with the first three components explaining 78% of variance. Species composition of diatoms is significantly correlated with environmental distance across geographical extent. The current pattern suggests that micro-environment at regional levels influences the species composition of epilithic diatoms in streams. The nestedness shown by the diatom community was highly significant, even though it had a high proportion of idiosyncratic species, characterized with high numbers of cosmopolitan species, whereas the nested species were dominated by endemic species. PCA identifies ionic parameters and nutrients as the major features which determine the characteristics of the sampling sites. Hence the local water quality parameters are the major factors in deciding the diatom species assemblages.

Effects of halogen substitution in nucleic acid components. Structure of sodium 5-bromocytidine 5'-phosphate hydrate

The conformation of 5-bromocytidine 5'-monophosphate in the title compound, Na+.C9H11BrN3O8P-.1.25H2O, is anti, C(3')-endo and gauche-gauche, similar to that in analogous non-halogenated nucleosides/nucleotides. The Na ion coordinates directly with phosphate O atoms and base atoms. Br is not involved in any stacking interaction.

Fracture Analysis of Concrete Structural Components Accounting for Tension Softening Effect

This paper presents methodologies for fracture analysis of concrete structural components with and without considering tension softening effect. Stress intensity factor (SIF) is computed by using analytical approach and finite element analysis. In the analytical approach, SW accounting for tension softening effect has been obtained as the difference of SIP obtained using linear elastic fracture mechanics (LEFM) principles and SIP due to closing pressure. Superposition principle has been used by accounting for non-linearity in incremental form. SW due to crack closing force applied on the effective crack face inside the process zone has been computed using Green's function approach. In finite element analysis, the domain integral method has been used for computation of SIR The domain integral method is used to calculate the strain energy release rate and SIF when a crack grows. Numerical studies have been conducted on notched 3-point bending concrete specimen with and without considering the cohesive stresses. It is observed from the studies that SW obtained from the finite element analysis with and without considering the cohesive stresses is in good agreement with the corresponding analytical value. The effect of cohesive stress on SW decreases with increase of crack length. Further, studies have been conducted on geometrically similar structures and observed that (i) the effect of cohesive stress on SW is significant with increase of load for a particular crack length and (iii) SW values decreases with increase of tensile strength for a particular crack length and load.

Evaluation of damage in foam sandwich components of aircraft

Tn the current set of investigations foam sandwich panels and some components of an aircraft comprising of two layer Glass Fiber Reinforced Plastic(GFRP) face sheets of thickness 1mm each with polyurethene foam as filler of thickness 8mm were examined for detection of debonds and defects. Known defects were introduced in the panels in the form of teflon insert, full foam removal,half foam removal and edge delamination by inserting a teflon and removing it after curing. Two such panels were subjected to acoustic impact and analysis was carried out in both time and frequency domains. These panels were ultrasonically scanned to obtain C-SCAN images as reference to evaluate Acoustic Impact Test (AIT) results. In addition both Fokker bond testing and AIT(woodpecker) were carried out on the same panels and also some critical joints on the actual component. The results obtained from these tests are presented and discussed in this paper.