A composition dependent thermal behavior of GexSe35-xTe65 glasses

Alternating differential scanning calorimetric (ADSC) studies have been performed to understand the thermal behavior of bulk GexSe35-xTe65 glasses (17 <= x <= 25); it is found that the glasses with x <= 20 exhibit two crystallization exotherms (T-c1 & T-c2). On the other hand, those with x >= 20.5, show a single crystallization reaction upon heating. The exothermic reaction at T-c1 has been found to correspond to the partial crystallization of the glass into hexagonal Te and the reaction at T-c2 is associated with the additional crystallization of rhombohedral Ge-Te phase. The glass transition temperature of GexSe35-xTe65 glasses is found to show a linear but not-steep increase, indicating a progressive, but a gradual increase in network connectivity with Ge addition. It is also found that T-c1 of GexSe35-xTe65 glasses with x <= 20, increases progressively with Ge content and eventually merges with T-c2 at x approximate to 20.5 (< r > = 2.41); this behavior has been understood on the basis of the reduction in Te-Te bonds of lower energy and increase in Ge-Te bonds of higher energy, with increasing Ge content. Apart from the interesting composition dependent crystallization, an anomalous melting behavior is also exhibited by the GexSe35-xTe65 glasses.

Differences in the Behavior of Luteinizing Hormones of Various Species at the Rat Gonadal Cell Receptor Site

The ability of different LH-like hormones, such as hCG, PMSG/equine (e) CG, ovine (o) LH, eLH, and rat (r) LH, to bind to and stimulate steroidogenesis in two types of rat gonadal cells was studied under the same experimental conditions. In both Leydig and granulosa cells, the maximal steroidogenic responses elicited by optimal doses of different LHs present during a 2-h incubation were comparable. However, if the cells were exposed to the different LHs for a brief period and then subjected to interference with hormone action by removing the unbound hormone from the medium by washing or adding specific antisera, differences were observed in the amount of steroid produced during subsequent incubation in hormone-free medium. Thus, in the case of hCG, either of these procedures carried out at 15 or 30 min of incubation had little inhibitory effect on the amount of steroid produced at 2 h, the latter being similar to that produced by cells incubated in the continued presence of hCG for 2 h. With eCG and rLH, the effect was dramatic, in that there was a total inhibition of subsequent steroidogenic response. In cells exposed to eLH and oLH, inhibition of subsequent steroidogenesis due to either removal of the free-hormone or addition of specific antisera at 15 or 30 min was only partial. Although all of the antisera used were equally effective in inhibiting the steroidogenic response to respective gonadotropins when added along with hormones at the beginning of incubation, differences were observed in the degree of inhibition of this response when the same antisera were added at later times of incubation. Thus, when antisera were added 60 min after the hormone, the inhibition of steroidogenesis was total (100%) for eCG, partial (10–40%) for eLH and oLH, and totally lacking in cells treated with hCG. From this, it appears that hCG bound to the receptor probably becomes unavailable for binding to its antibody with time, while in the case of eCG and other LHs used, the antibody can still inhibit the biological activity of the hormone. Studies with 125I-labeled hormones further supported the conclusion that hCG differs from all other LHs in being most tightly bound and, hence, least dissociable, while eCG and rLH dissociate most readily; oLH and eLH can be placed in between these hormones in the extent of their dissociability. (Endocrinology 116: 597–603,1985)

Influence of heat-treatment on the strength and fracture-behavior of fe-12cr-6al ferritic stainless-steel

The changes in the tensile properties and fracture mode brought about by heat treatment of Fe-12Cr-6Al ferritic stainless steel have been studied. A favourable combination of high strength and good ductility is obtained by heating the material at 1370 K for 2 h followed by a water quench. The high-temperature treatment results in carbide dissolution as well as an increase in the grain size. The mechanism of strengthening has been evaluated from the apparent activation energy (28 kJ mol–1) and is identified to be the unpinning of dislocations from the atmosphere of carbon atoms. As the heat-treatment temperature is increased, the fracture behaviour changes from ductile to brittle mode and this is related to the changes in grain size and friction stress.

Behavior of the indian social wasp ropalidia-cyathiformis on a nest of separate combs (hymenoptera, vespidae)

Observations were made on a nest of Ropalidia cyathiformis consisting of three combs. The number of eggs, larvae, pupae and adults were monitored at about 3-day intervals for a 2-month period. The behaviour of the adults was observed with special reference to the proportion of time spent on each of the three combs, the proportion of time spent away from the nest site and the frequencies of dominance interactions and egg laying. The adults moved freely between the three combs suggesting that all of them and all the three combs belonged to one nest. However, most of the adults preferred combs 2 and 3 over comb 1. Of the 10 animals chosen for a detailed analysis of behaviour, seven spent varying periods of time away from the nest site and oRen brought back food or building material. Five of the 10 animals laid at least one egg each but two adults monopolized most of the egg-laying. The animals showed a variety of dominance interactions on the basis of which they have been arranged in a dominance hierarchy. The dominant individuals laid most of the eggs and spent little or no time foraging, while the subordinate individuals spent more time foraging and laid few eggs or none. It is argued that R. cyathiformis is different from R. marginata, the only other Indian social wasp whose behaviour has been studied, in being at a more primitive stage of social organization.

Stochastic kinetics of ribosomes: Single motor properties and collective behavior

Syntheses of protein molecules in a cell are carried out by ribosomes.A ribosome can be regarded as a molecular motor which utilizes the input chemical energy to move on a messenger RNA (mRNA) track that also serves as a template for the polymerization of the corresponding protein. The forward movement, however, is characterized by an alternating sequence of translocation and pause. Using a quantitative model, which captures the mechanochemical cycle of an individual ribosome, we derive an exact analytical expression for the distribution of its dwell times at the successive positions on the mRNA track. Inverse of the average dwell time satisfies a Michaelis-Menten-type'' equation and is consistent with the general formula for the average velocity of a molecular motor with an unbranched mechanochemical cycle. Extending this formula appropriately, we also derive the exact force-velocity relation for a ribosome. Often many ribosomes each synthesizes a copy of the same protein. We extend the model of a single ribosome by incorporating steric exclusion of different individuals on the same track. We draw the phase diagram of this model of ribosome traffic in three-dimensional spaces spanned by experimentally controllable parameters. We suggest new experimental tests of our theoretical predictions.

Observation of reentrant spin glass behavior in LaCo0.5Ni0.5O3

The magnetic and transport properties of LaCo0.5Ni0.5O3 have been studied. The dc magnetization and the ac susceptibility studies suggest the presence of a magnetic-phase transition from a ferromagnetic (FM) to a spin glass phase at a low temperature. This type of reentrant spin-glass (RSG) behavior attached to a long-range ordered ferromagnet is observed in this system. A magnetoresistance of ~10% is observed at 5 K which is unsaturated up to 11 Tesla suggests the presence of antiferromagnetic (AFM) interactions. It is likely that the competition between such AFM interactions with FM interactions yield an RSG phase.

Spectroscopic and Coordination Behavior of α-Cyanothioacetamide

α-Cyanothioacetamide (CTAM) complexes of cuprous chloride CuCl–2CTAM and cuprous bromide CuBr–2CTAM have been prepared. The infrared spectra of CTAM and its complexes, and the laser Raman spectrum of CTAM have been recorded. Assignment of the frequencies of the ligand has been made on the basis of a normal coordinate analysis using the Urey-Bradley force field. The copper (I) complexes are inferred to have thiocarbonyl sulfur and amide nitrogen bonded CTAM as evidenced from infrared and electronic spectra.

Studies on dielectric behavior of insulator-conductor composites

This paper describes the dielectric behavior of an insulator-conductor composite, namely, the wax-graphite composite. The variation of specific capacitance of these composites with parameters such as volume fraction and grain size of the conducting particles and temperature has been studied. These observed variations have been explained using the same model [C. Rajagopal and M. Satyam, J. Appl. Phys. 49, 5536 (1978)] which explains electrical conduction in composites. The specific capacitance of these materials appears to be governed by the contact capacitance between the conducting particles and the number of contacts each particle has with its neighbors. The variation of specific capacitance with temperature is attributed to the change in contact area.

Fracture Behavior of Multidirectional DCB Specimen: Higher-Order Beam Theories

Mathematical models, for the stress analysis of symmetric multidirectional double cantilever beam (DCB) specimen using classical beam theory, first and higher-order shear deformation beam theories, have been developed to determine the Mode I strain energy release rate (SERR) for symmetric multidirectional composites. The SERR has been calculated using the compliance approach. In the present study, both variationally and nonvariationally derived matching conditions have been applied at the crack tip of DCB specimen. For the unidirectional and cross-ply composite DCB specimens, beam models under both plane stress and plane strain conditions in the width direction are applicable with good performance where as for the multidirectional composite DCB specimen, only the beam model under plane strain condition in the width direction appears to be applicable with moderate performance. Among the shear deformation beam theories considered, the performance of higher-order shear deformation beam theory, having quadratic variation for transverse displacement over the thickness, is superior in determining the SERR for multidirectional DCB specimen.

Evolution of Social Behavior Through Interpopulation Selection

Under certain special conditions natural selection can be effective at the level of local populations, or demes. Such interpopulation selection will favor genotypes that reduce the probability of extinction of their parent population even at the cost of a lowered inclusive fitness. Such genotypes may be characterized by altruistic traits only in a viscous population, i.e., in a population in which neighbors tend to be closely related. In a non-viscous population the interpopulation selection will instead favor spiteful traits when the populations are susceptible to extinction through the overutilization of the habitat, and cooperative traits when it is the newly established populations that are in the greatest danger of extinction.

Load-Deflection Behavior of Restrained R/C Skew Slabs

A method is presented for determining the complete load-deflection behavior of reinforced concrete skew slabs restrained at the edges and subjected to uniformly-distributed loading. The analysis is considered in three stages. In the first stage the load-deflection behavior up to the cracking load is considered. The behavior between the cracking load and the yield line load is considered in the second stage. The load-deflection behavior beyond the yield line load, taking into account the effect of the membrane action, is considered in the third stage. Details of an experimental program of casting and testing 12 reinforced concrete skew slabs restrained at the edges are presented to verify the results of the analysis.

Role of cell attachment in leaching of chalcopyrite mineral by Thiobacillus ferrooxidans

Experiments on the leaching of copper from chalcopyrite mineral by the bacterium Thiobacillus ferrooxidans show that, in the presence of adequate amounts of sulphide, iron-grown bacteria preferentially oxidise sulphur in the ore (through direct attachment) rather than ferrous sulphate in solution. At 20% pulp density, the leaching initially takes place by a predominantly direct mechanism. The cell density in the liquid phase increases, but the Fe2+ is not oxidised. However, in the later stages when less solid substrate is available and the cell density becomes very high, the bacteria start oxidising Fe2+ in the liquid phase, thus contributing to the indirect mechanism of leaching. Contrary to expectations, the rate of leaching increased with increasing particle size in spite of the decreasing specific surface area. This has been found to be due to increasing attachment efficiency with increase in particle size.

Palladium(II) and platinum(II) complexes of beta-functionalized ethyl selenolates: Effect of substitution on synthesis, reactivity, spectroscopy, structures and thermal behavior

Sodium ethylselenolates with functional groups X (where X = -OH, -COOH, -COOMe and -COOEt) at beta-carbon were prepared in situ by reductive cleavage of corresponding diselenide with NaBH4 either in methanol or aqueous ammonia. Treatment of these selenolates with [M2Cl2(mu-Cl)(2)(PR'(3))(2)] (M = Pd or Pt; PR'(3) = PMePh2, PnPr(3)) in different stoichiometry yielded various bi- and tri-nuclear complexes. The homoleptic hexanuclear complexes [Pd(mu-SeCH2CH2X)(2)](6) (X = OH, COOH, COOEt), were obtained by reacting Na2PdCl4 with NaSeCH2CH2X. All these complexes have been fully characterized. Molecular structures of ethylselenolates containing hydroxyl and carboxylic acid groups revealed solid state associated structures through inter-molecular hydrogen bond interactions. Trinuclear complex, [Pd3Cl2(mu-SeCH2CH2COOH)(4)(PnPr(3))(2)] (3a), was disposed in a boat form unlike chair conformation observed for the corresponding methylester complex. The effect of beta-functionality in ethylselenolate ligands towards reactivity, structures and thermal properties of palladium and platinum complexes has been extensively Studied.

Cellular Automata Models of Traffic Behavior in Presence of Speed Breaking Structures

In this article, we study traffic flow in the presence of speed breaking structures. The speed breakers are typically used to reduce the local speed of vehicles near certain institutions such as schools and hospitals. Through a cellular automata model we study the impact of such structures on global traffic characteristics. The simulation results indicate that the presence of speed breakers could reduce the global flow under moderate global densities. However, under low and high global density traffic regime the presence of speed breakers does not have an impact on the global flow. Further the speed limit enforced by the speed breaker creates a phase distinction. For a given global density and slowdown probability, as the speed limit enforced by the speed breaker increases, the traffic moves from the reduced flow phase to maximum flow phase. This underlines the importance of proper design of these structures to avoid undesired flow restrictions.

An Experimental Study on Energy Absorption Behavior of Polyurethane Foams

This article is concerned with a study on the energy absorption behavior of polyurethane (PU) foams such as flexible high resilience (HR), flexible viscoelastic (VE) and semi-rigid (SR) foams as a function of the overall foam density. Foam samples were prepared in the form of cubes by mixing appropriate polyol and isocyanate compounds produced by Huntsman International India Pvt. Ltd. in varying proportions leading to a range of densities for each type of foam. The cubical samples were tested under compressive load in a standard UTM. Based on the measured load-displacement behaviors, variations of peak load and energy-absorption attributes with respect to density are plotted for each type of foam and the possible existence of an optimum foam density is shown.