Rocket Propellant Combustion Studies in a Constant Volume Bomb

A constant volume window bomb has been used to measure the characteristic velocity (c*) of rocket propellants. Analysis of the combustion process inside the bomb including heat losses has been made. The experiments on double base and composite propellants have revealed some (i) basic heat transfer aspects inside the bomb and (ii) combustion characteristics of Ammonium Perchlorate-Polyester propellants. It has been found that combustion continues even beyond the peak pressure and temperature points. Lithium Fluoride mixed propellants do not seem to indicate significant differences in c*) though the low pressure deflagration limit is increased with percentage of Lithium Fluoride.

Lower Bound Limit Analysis of Rectangular Slabs

A general method for the development of valid lower bound solutions to uniformly distributed and orthotropically reinforced rectangular concrete slabs obeying normal moment criterion is described. General expressions for moment field have been obtained for nine cases of slabs having all combinations of simply supported and clamped-edge conditions. The lower bound collapse loads have been compared with the upper bound values obtained by the yield line theory. The paper also focuses attention to the need for the development of valid upper bound solutions with the satisfaction of kinematical admissibility and the flow rules associated with the normal moment criterion.

Estimation of higher natural frequencies of polar orthotropic annular plates

A method based on an assumption that the radial bending moment is zero at a nodal circle is shown to yield accurate estimates of natural frequencies corresponding to higher modes of transversely vibrating polar orthotropic annular plates for various combinations of clamped, simply supported and free edge conditions. This method is found to be convenient for the determination of locations of nodal circles as well. Numerical investigations revealed that for small holes, nodal circles tend to move towards the outer edge with increasing number of nodal diameters. For large holes, it has been shown that the plate behaves like a long rectangular strip.

Free vibration of rectangular plates of arbitrary thickness with one or more edges clamped

Frequencies of free vibration of rectangular plates of arbitrary thickness, with different support conditions, are calculated by using the Method of Initial Functions (MIF), proposed by Vlasov. Sixth and fourth order MIF theories are used for the solution. Numerical results are presented for three square plates for three thickness ratios. The support conditions considered are (i) three sides simply supported and one side clamped, (ii) two opposite sides simply supported and the other two sides clamped and (iii) all sides clamped. It is found that the results produced by the MIF method are in fair agreement with those obtained by using other methods. The classical theory gives overestimates of the frequencies and the departures from the MIF results increase for higher modes and larger thickness ratios.

Recognition of Interaction Interface Residues in Low-Resolution Structures of Protein Assemblies Solely from the Positions of C alpha Atoms

Background: The number of available structures of large multi-protein assemblies is quite small. Such structures provide phenomenal insights on the organization, mechanism of formation and functional properties of the assembly. Hence detailed analysis of such structures is highly rewarding. However, the common problem in such analyses is the low resolution of these structures. In the recent times a number of attempts that combine low resolution cryo-EM data with higher resolution structures determined using X-ray analysis or NMR or generated using comparative modeling have been reported. Even in such attempts the best result one arrives at is the very course idea about the assembly structure in terms of trace of the C alpha atoms which are modeled with modest accuracy. Methodology/Principal Findings: In this paper first we present an objective approach to identify potentially solvent exposed and buried residues solely from the position of C alpha atoms and amino acid sequence using residue type-dependent thresholds for accessible surface areas of C alpha. We extend the method further to recognize potential protein-protein interface residues. Conclusion/Significance: Our approach to identify buried and exposed residues solely from the positions of C alpha atoms resulted in an accuracy of 84%, sensitivity of 83-89% and specificity of 67-94% while recognition of interfacial residues corresponded to an accuracy of 94%, sensitivity of 70-96% and specificity of 58-94%. Interestingly, detailed analysis of cases of mismatch between recognition of interface residues from C alpha positions and all-atom models suggested that, recognition of interfacial residues using C alpha atoms only correspond better with intuitive notion of what is an interfacial residue. Our method should be useful in the objective analysis of structures of protein assemblies when positions of only C alpha positions are available as, for example, in the cases of integration of cryo-EM data and high resolution structures of the components of the assembly.

Vibration of rectangular orthotropic plates

An approximate analytical procedure has been given to solve the problem of a vibrating rectangular orthotropic plate, with various combinations of simply supported and clamped boundary conditions. Numerical results have been given for the case of a clamped square plate. Nomenclature 2a, 2b sides of the rectangular plate h plate thickness Eprime x , Eprime y , EPrime, G elastic constants of te orthotropic material D x Eprime x h 3/12 D y Eprime y h 3/12 H xy EPrimeh 3/12+Gh 3/6 D x , D y and H xy are rigidity constants of the orthotropic platergr mass of the plate per unit area ngr Poisson's ratio W deflection of the plate p circular frequency gamma b/a ratio X m , Y characteristic functions of the vibrating beam problem -lambda rgrp 2 a 2 b 2/H xy the frequency parameter.

On the use of a coordinate transformation for analysis of axisymmetric vibration of polar orthotropic annular plates

Estimates of natural frequencies corresponding to axisymmetric modes of flexural vibration of polar orthotropic annular plates have been obtained for various combinations of clamped, simply supported and free edge conditions. A coordinate transformation in the radial direction has been used to obtain effective solutions by the classical Rayleigh-Ritz method. The analysis with this transformation has been found to be advantageous in computations, particularly for large hole sizes, over direct analysis. Numerical results have been obtained for various values of hole sizes and rigidity ratio. The eigenvalue parameter has been found to vary more or less linearly with the rigidity ratio. A comparison with the results for isotropic plates has brought out some interesting features.

Theoretical Estimation of Length Dependent In-Plane Stiffness of Single Walled Carbon Nanotubes Using the Nonlocal Elasticity Theory

In the present paper, Eringen's nonlocal elasticity theory is employed to evaluate the length dependent in-plane stiffness of single-walled carbon nanotubes (SWCNTs). The SWCNT is modeled as an Euler-Bernoulli beam and is analyzed for various boundary conditions to evaluate the length dependent in-plane stiffness. It has been found that the nonlocal scaling parameter has a significant effect on the length dependent in-plane stiffness of SWCNTs. It has been observed that as the nonlocal scale parameter increases the stiffness ratio of SWCNT decreases. In nonlocality, the cantilever SWCNT has high in-plane stiffness as compared to the simply-supported and the clamped cases.

Laminar compressible boundary layer flow at a three-dimensional stagnation point with vectored mass transfer

The effect of surface mass transfer velocities having normal, principal and transverse direction components (�vectored� suction and injection) on the steady, laminar, compressible boundary layer at a three-dimensional stagnation point has been investigated both for nodal and saddle points of attachment. The similarity solutions of the boundary layer equations were obtained numerically by the method of parametric differentiation. The principal and transverse direction surface mass transfer velocities significantly affect the skin friction (both in the principal and transverse directions) and the heat transfer. Also the inadequacy of assuming a linear viscosity-temperature relation at low-wall temperatures is shown.

Comparison of heat transfer correlations for cryogenic engine thrustchamber design

A comparative study of the correlations available in the literature is made to arrive at an appropriate pair for estimating the coolant-side and hot-gas-side heat transfer coefficients in the thrust chamber of a cryogenic engine. Based on this, the thermal analysis of a supercritical liquid hydrogen cooled engine is carried out. Results are presented for axial variation of heat transfer coefficients and temperature distributions for coolant and exposed wall. Tubular as well as milled channel configurations are considered for coolant flow.

Ultimate Strength of R.C. Wall Panels in Two-Way In-Plane Action

Test results of 24 reinforced concrete wall panels in two-way action (i.e., supported on all the four sides) and subjected to in-plane vertical load are presented. The load is applied at an eccentricity to represent possible accidental eccentricity that occurs in practice due to constructional imperfections. Influences of aspect ratio, thinness ratio, slendemess ratio, vertical steel, and horizontal steel on the ultimate load are studied. Two equations are proposed to predict the ultimate load carried by the panels. The first equation is empirical and is arrived at from trial and error fitting with test data. The second equation is semi-empirical and is developed from a modification of the buckling strength of thin rectangular plates. Both the equations are formulated so as to give a safe prediction of a large portion of ultimate strength test results. Also, ultimate load cracking load and lateral deflections of identical panels in two-way action (all four sides supported) and oneway action (top and bottom sides only supported) are compared.

AN ITERATIVE ALGORITHM FOR PHASE RETRIEVAL WITH SPARSITY CONSTRAINTS: APPLICATION TO FREQUENCY DOMAIN OPTICAL COHERENCE TOMOGRAPHY

We address the problem of phase retrieval, which is frequently encountered in optical imaging. The measured quantity is the magnitude of the Fourier spectrum of a function (in optics, the function is also referred to as an object). The goal is to recover the object based on the magnitude measurements. In doing so, the standard assumptions are that the object is compactly supported and positive. In this paper, we consider objects that admit a sparse representation in some orthonormal basis. We develop a variant of the Fienup algorithm to incorporate the condition of sparsity and to successively estimate and refine the phase starting from the magnitude measurements. We show that the proposed iterative algorithm possesses Cauchy convergence properties. As far as the modality is concerned, we work with measurements obtained using a frequency-domain optical-coherence tomography experimental setup. The experimental results on real measured data show that the proposed technique exhibits good reconstruction performance even with fewer coefficients taken into account for reconstruction. It also suppresses the autocorrelation artifacts to a significant extent since it estimates the phase accurately.

Information capacity of energy harvesting sensor nodes

Sensor nodes with energy harvesting sources are gaining popularity due to their ability to improve the network life time and are becoming a preferred choice supporting `green communication'. We study such a sensor node with an energy harvesting source and compare various architectures by which the harvested energy is used. We find its Shannon capacity when it is transmitting its observations over an AWGN channel and show that the capacity achieving energy management policies are related to the throughput optimal policies. We also obtain the capacity when energy conserving sleep-wake modes are supported and an achievable rate for the system with inefficiencies in energy storage.

How to be a fig wasp parasite on the fig-fig wasp mutualism

The nursery pollination mutualism between figs and pollinating fig wasps is based on adaptations that allow wasps to enter the enclosed inflorescences of figs, to facilitate seed set, and to have offspring that develop within the nursery and that leave to enter other inflorescences for pollination. This closed mutualistic system is not immune to parasitic fig wasps. Although the life histories and basic biology of the mutualists have been investigated, the biology of the fig wasp parasites has been severely neglected. This review brings together current knowledge of the many different ways in which parasites can enter the system, and also points to the serious lacunae in our understanding of the intricate interactions between gallers, kleptoparasites, seed eaters and parasitoids within this mutualism.