Natural frequencies of rectangular orthotropic plates with a pair of parallel edges simply supported

Solutions of the exact characteristic equations for the title problem derived earlier by an extension of Bolotin's asymptotic method are considered. These solutions, which correspond to flexural modes with frequency factor, R, greater than unity, are expressed in convenient forms for all combinations of clamped, simply supported and free conditions at the remaining pair of parallel edges. As in the case of uniform beams, the eigenvalues in the CC case are found to be equal to those of elastic modes in the FF case provided that the Kirchoff's shear condition at a free edge is replaced by the condition. The flexural modes with frequency factor less than unity are also investigated in detail by introducing a suitable modification in the procedure. When Poisson's ratios are not zero, it is shown that the frequency factor corresponding to the first symmetric mode in the free-free case is less than unity for all values of side ratio and rigidity ratios. In the case of one edge clamped and the other free it is found that modes with frequency factor less than unity exist for certain dimensions of the plate—a fact hitherto unrecognized in the literature.

Wave analysis of sound decay in rectangular rooms

The decay of sound in a rectangular room is analyzed for various boundary conditions on one of its walls. It is shown that the decay of the sound-intensity level is in general nonlinear. But for specific areas and impedances of the material it is possible to obtain a linear initial decay. It is also shown that the coefficients derived from the initial decay rates neither correspond to the predictions of Sabine's or Eyring's geometrical theories nor to the normal coefficients of Morse's wave theory. The dependence of the coefficients on the area of the material is discussed. The influence of the real and the imaginary parts of the specific acoustic impedance of the material on the coefficients is also discussed. Finally, the existence of a linear initial decay corresponding to the decay of a diffuse field in the case of a highly absorbing material partially covering a wall is explained on the basis of modal coupling.

Wave analysis of sound decay in rectangular rooms

The decay of sound in a rectangular room is analyzed for various boundary conditions on one of its walls. It is shown that the decay of the sound-intensity level is in general nonlinear. But for specific areas and impedances of the material it is possible to obtain a linear initial decay. It is also shown that the coefficients derived from the initial decay rates neither correspond to the predictions of Sabine's or Eyring's geometrical theories nor to the normal coefficients of Morse's wave theory. The dependence of the coefficients on the area of the material is discussed. The influence of the real and the imaginary parts of the specific acoustic impedance of the material on the coefficients is also discussed. Finally, the existence of a linear initial decay corresponding to the decay of a diffuse field in the case of a highly absorbing material partially covering a wall is explained on the basis of modal coupling.

Velocity Distribution in Smooth Rectangular Open Channels-Closure

Abstract is not available.

Lower Bound Limit Analysis of Rectangular Slabs

A general method for the development of valid lower bound solutions to uniformly distributed and orthotropically reinforced rectangular concrete slabs obeying normal moment criterion is described. General expressions for moment field have been obtained for nine cases of slabs having all combinations of simply supported and clamped-edge conditions. The lower bound collapse loads have been compared with the upper bound values obtained by the yield line theory. The paper also focuses attention to the need for the development of valid upper bound solutions with the satisfaction of kinematical admissibility and the flow rules associated with the normal moment criterion.

Free vibration of rectangular plates of arbitrary thickness

Free vibration of thick rectangular plates is investigated by using the “method of initial functions” proposed by Vlasov. The governing equations are derived from the three-dimensional elastodynamic equations. They are obtained in the form of series and theories of any desired order can be constructed by deleting higher terms in the infinite order differential equations. The numerical results are compared with those of classical, Mindlin, and Lee and Reismann solutions.

Dielectric-lined rectangular metal waveguide

The propagation characteristics of electromagnetic waves in a dielectric-lined rectangular metal waveguide have been studied. The lining on the two side walls (E-plane) together with the air space in between them is considered as a homogeneous equivalent dielectric medium whose equivalent dielectric constant is derived by using electrostatic theory. The theoretical work is based on the fact that LSE and LSM modes can be propagated in a rectangular metal waveguide lined in the two longer sides (H-plane) by dielectric lining. Experimental verification of the guide wavelength at 'X', 'ku' and 'Ka' bands and cut-off frequency are reported.

Free vibration of rectangular plates of arbitrary thickness with one or more edges clamped

Frequencies of free vibration of rectangular plates of arbitrary thickness, with different support conditions, are calculated by using the Method of Initial Functions (MIF), proposed by Vlasov. Sixth and fourth order MIF theories are used for the solution. Numerical results are presented for three square plates for three thickness ratios. The support conditions considered are (i) three sides simply supported and one side clamped, (ii) two opposite sides simply supported and the other two sides clamped and (iii) all sides clamped. It is found that the results produced by the MIF method are in fair agreement with those obtained by using other methods. The classical theory gives overestimates of the frequencies and the departures from the MIF results increase for higher modes and larger thickness ratios.

Low ML-Decoding Complexity, Large Coding Gain, Full-Rate, Full-Diversity STBCs for 2 x 2 and 4 x 2 MIMO Systems

This paper deals with low maximum-likelihood (ML)-decoding complexity, full-rate and full-diversity space-time block codes (STBCs), which also offer large coding gain, for the 2 transmit antenna, 2 receive antenna (2 x 2) and the 4 transmit antenna, 2 receive antenna (4 x 2) MIMO systems. Presently, the best known STBC for the 2 2 system is the Golden code and that for the 4 x 2 system is the DjABBA code. Following the approach by Biglieri, Hong, and Viterbo, a new STBC is presented in this paper for the 2 x 2 system. This code matches the Golden code in performance and ML-decoding complexity for square QAM constellations while it has lower ML-decoding complexity with the same performance for non-rectangular QAM constellations. This code is also shown to be information-lossless and diversity-multiplexing gain (DMG) tradeoff optimal. This design procedure is then extended to the 4 x 2 system and a code, which outperforms the DjABBA code for QAM constellations with lower ML-decoding complexity, is presented. So far, the Golden code has been reported to have an ML-decoding complexity of the order of for square QAM of size. In this paper, a scheme that reduces its ML-decoding complexity to M-2 root M is presented.

A Compact Defected Ground Microstrip Device with Photonic Bandgap Effects

Filters and other devices using photonic bandgap (PBG) theory are typically implemented in microstrip lines by etching periodic holes on the ground plane of the microstrip. The period of such several holes corresponds to nearly half the guided wavelength of the transmission line. In this paper we study the effects of miniaturization of the PBG device by meandering the microstrip line about one single hole in the ground plane. A comparison of the S-parameters and dispersion behavior of the modified geometry and a conventional PBG device with a straight microstrip line shows that these devices have similar behaviors.

Anion directed template synthesis of Cu(II) complexes of a N,N,O donor mono-condensed Schiff base ligand: A molecular scaffold forming highly ordered H-bonded rectangular grids

Anion directed, template syntheses of two dinuclear copper(II) complexes of mono-condensed Schiff base ligand Hdipn (4-[(3-aminopentylimino)-methyl]-benzene-1,3-diol) involving 2,4- dihydroxybenzaldehyde and 1,3-diaminopentane were realized in the presence of bridging azide and acetate anions. Both complexes, [Cu-2(dipn)(2)(N-3)(2)] (1) and [Cu-2(dip(n))(2)(OAc)(2)] (2) have been characterized by X-ray crystallography. The two mononuclear units are joined together by basal-apical, double end-on azido bridges in complex 1 and by basal-apical, double mono-atomic acetate oxygen-bridges in 2. Both complexes form rectangular grid-like supramolecular structures via H-bonds connecting the azide or acetate anion and the p-hydroxy group of 2,4- dihydroxybenzaldehyde. Variable-temperature (300-2 K) magnetic susceptibility measurements reveal that complex 1 has antiferromagnetic coupling (J = -2.10 cm (1)) through the azide bridge while 2 has intra-dimer ferromagnetic coupling through the acetate bridge and inter-dimer antiferromagnetic coupling through H-bonds (J = 2.85 cm (1), J' = -1.08 cm (1)). (C) 2009 Elsevier B. V. All rights reserved.

DMT of Multi-hop Cooperative Networks-Part II: Layered and Multi-Antenna Networks

We consider single-source, single-sink (ss-ss) multi-hop relay networks, with slow-fading Rayleigh links. This two part paper aims at giving explicit protocols and codes to achieve the optimal diversity-multiplexing tradeoff (DMT) of two classes of multi-hop networks: K-parallel-path (KPP) networks and Layered networks. While single-antenna KPP networks were the focus of the first part, we consider layered and multi-antenna networks in this second part. We prove that a linear DMT between the maximum diversity d(max). and the maximum multiplexing gain of 1 is achievable for single-antenna fully-connected layered networks under the half-duplex constraint. This is shown to be equal to the optimal DMT if the number of relaying layers is less than 4. For the multiple-antenna case, we provide an achievable DMT, which is significantly better than known lower bounds for half duplex networks. Along the way, we compute the DMT of parallel MIMO channels in terms of the DMT of the component channel. For arbitrary ss-ss single-antenna directed acyclic networks with full-duplex relays, we prove that a linear tradeoff between maximum diversity and maximum multiplexing gain is achievable using an amplify-and-forward (AF) protocol. Explicit short-block-length codes are provided for all the proposed protocols. Two key implications of the results in the two-part paper are that the half-duplex constraint does not necessarily entail rate loss by a factor of two as previously believed and that simple AN protocols are often sufficient to attain the best possible DMT.

Dual-frequency characteristics of Minkowski-square ring antennas

Fractal Minkowski curves to design a compact dual-frequency microstrip ring antenna are proposed. Sides of a square ring have been selectively replaced with first and second iterations of the generalised fractal geometry to design a smaller antenna with dual-frequency operation. This behaviour has been explained based on current distributions on the antenna structure. Measured results compare well with electromagnetic simulations.

Stress concentration and load diffusion in rectangular panels with constant stress flanges

The stress concentration that occurs when load is diffused from a constant stress member into thin sheet is an important problem in the design of light weight structures. By using solutions in biharmonic polar-trigonometric series, the stress concentration can be effectively isolated so that highly accurate information necessary for design can be obtained. A method of analysis yielding high accuracy with limited effort is presented for rectangular panels with transverse edges free or supported by inextensional end ribs. Numerical data are given for panels with length twice the width.

Large deflections of rectangular plates

Approximate solutions for the non-linear bending of thin rectangular plates are presented considering large deflections for various boundary conditions. In the case of stress-free edges, solutions are given for von Kármán's equations in terms of the stress function and the deflection of the plate. In the case of immovable edges, equations are constructed in terms of the three displacements and these are solved. The solution is given by using double series consisting of the appropriate Beam Functions which satisfy the boundary conditions. The differential equations are satisfied by using the orthogonality properties of the series. Numerical results for square plates with uniform lateral load indicate good convergence of the series solution presented here.