Relationship Between Physical Structure and Tribology of Single Soot Particles Generated by Burning Ethylene

Ethylene gas is burnt and the soot generated is sampled thermophoretically at different heights along the flame axis starting from a region close to the root of the flame. The morphology and crystallinity of the particle are recorded using high resolution transmission electron microscopes. The hardness of a single particle is measured using a nanoindenter. The frictional resistance and material removal of a particle are measured using an atomic force microscope. The particles present in the mid-flame region are found to have a crystalline shell. The ones at the flame root are found to be highly disordered and the ones at the flame tip and above have randomly distributed pockets of short range order. The physical state of a particle is found to relate, but not very strongly, with the mechanical and tribological properties of the particles.

Physical chemistry of mixed conducting zirconia ceramics

Suivant la pression partielle d'oxygène, la zircone peut être conducteur ionique ou électronique. Mise au point de méthodes de mesures de f.é.m. permettant de s'affranchir des sources d'erreur introduites par ces propriétés.

Physical chemistry of the reduction of calcium oxide with aluminium in vacuum

The physical chemistry of "aluminothermic" reduction of calcium oxide in vacuum is analyzed. Basic thermodynamic data required for the analysis have been generated by a variety of experiments. These include activity measurements in liquid AI-Ca alloys and determination of the Gibbs energies of formation of calcium aluminates. These data have been correlated with phase relations in the Ca-AI-0 system at 1373 K. The various stages of reduction, the end products and the corresponding equilibrium partial pressures of calcium have been established from thermodynamic considerations. In principle, the recovery of calcium can be improved by reducing the pressure in the reactor. However,, the cost of a high vacuum system and the enhanced time for reduction needed to achieve higher yields makes such a practice uneconomic. Aluminum contamination of calcium also increases at low pressures. The best compromise is to carry the reduction up to the stage where 3CaO-Al,O, is formed as the product. This corresponds to an equilibrium calcium partial pressure of 31.3 Pa at 1373 K and 91.6 Pa at 1460 K. Calcium can be extracted at this pressure using mechanical pumps in approximately 8 to 15 hr, depending on the size and the fill ratio of the retort and porosity of the charge briquettes.

15-deoxyspergualin hinders physical interaction between basic residues of transit peptide in PfENR and Hsp70-1

The apicoplast of Plasmodium harbors several metabolic pathways. The enzymes required to perform these reactions are all nuclearly encoded and apicoplast targeted (NEAT) proteins. Plasmodium falciparum Enoyl-ACP Reductase (PfENR) is one such NEAT protein. The NEAT proteins have a transit peptide which is required for crossing the membranes of apicoplast. We studied the importance of basic residues like Arginine and Lysine within the transit peptide. Previous studies have suggested that all basic residues are essential for apicoplast trafficking. In this study, we demonstrate that only some of these residues are essential (K44, R48, K51, and R52), whereas others are dispensable (R40, K42, and K49). On mutating these specific residues, PfENR is not imported into the apicoplast and is mislocalized to the cytoplasm. We also demonstrate that these residues are also crucial for interaction with Hsp70-1, implying that interactions of Lysine 44, Arginine 48, Lysine 51, and Arginine 52 of the transit peptide with PfHsp70-1 are required for apicoplast trafficking. 15-Deoxyspergualin, which has earlier been proposed to interact with EEVD motif of PfHsp70-1 hinders the physical interaction between these cationic residues of PfENR and Hsp70-1. Hence, we propose that in the transport competent state of NEAT proteins some specific positively charged amino acids in the transit peptide interact with PfHsp70-1, and this interaction is essential for apicoplast targeting.

Tribology of soot suspension in hexadecane as distinguished by the physical structure and chemistry of soot particles

Ethylene gas is burnt to generate soot which is collected thermophoretically from different locations of the flame. Tribological performance of the collected soot in hexadecane suspension is compared with that of carbon black and diesel soot. The soots are analysed to yield a range of mechanical properties, physical structures and chemistry. The paper correlates these property variations with the corresponding variations in friction and wear when the soot suspended in hexadecane is used to lubricate a steel on steel sliding interaction. The particles are dispersed in hexadecane by a non-ionic surfactant, poly-isobutylene succinimide (PIBS), which is mono-functional with no free amine group. The grafting of the surfactant on the soot particles is found to have a profound effect on the dispersion of the soot, in general, while, between the different soot types, the tribology is differentiated by the physical structure and chemistry.

Thermo-physical and structural studies of sodium zinc borovanadate glasses in the region of high concentration of modifier oxides

This paper reports investigation of Na2O and ZnO modified borovanadate glasses in the highly modified regime of compositions. These glasses have been prepared by microwave route. Ultraviolet (UV) and visible, infrared (IR), Magic Angle Spinning Nuclear Magnetic Resonance (MAS NMR) and Electron Paramagnetic Resonance (EPR) spectroscopies have been used to characterize the speciation in the glasses. Together with the variation of properties such as molar volume and glass transition temperatures, spectroscopic data indicate that at high levels of modification, ZnO tends to behave like network former. It is proposed that the observed variation of all the properties can be reasonably well understood with a structural model. The model considers that the modification and speciation in glasses are strongly determined by the hierarchy of group electronegativities. Further, it is proposed that the width of the transitions of glasses obtained under same condition reflects the fragility of the glasses. An empirical expression has been suggested to quantify fragility on the basis of width of the transition regions. (C) 2012 Elsevier Ltd. All rights reserved.

Substrate temperature influenced physical properties of silicon MOS devices with TiO2 gate dielectric

DC reactive magnetron sputtering technique was employed for deposition of titanium dioxide (TiO2) films. The films were formed on Corning glass and p-Si (100) substrates by sputtering of titanium target in an oxygen partial pressure of 6x10-2 Pa and at different substrate temperatures in the range 303 673 K. The films formed at 303 K were X-ray amorphous whereas those deposited at substrate temperatures?=?473 K were transformed into polycrystalline nature with anatase phase of TiO2. Fourier transform infrared spectroscopic studies confirmed the presence of characteristic bonding configuration of TiO2. The surface morphology of the films was significantly influenced by the substrate temperature. MOS capacitor with Al/TiO2/p-Si sandwich structure was fabricated and performed currentvoltage and capacitancevoltage characteristics. At an applied gate voltage of 1.5 V, the leakage current density of the device decreased from 1.8?x?10-6 to 5.4?x?10-8 A/cm2 with the increase of substrate temperature from 303 to 673 K. The electrical conduction in the MOS structure was more predominant with Schottky emission and Fowler-Nordheim conduction. The dielectric constant (at 1 MHz) of the films increased from 6 to 20 with increase of substrate temperature. The optical band gap of the films increased from 3.50 to 3.56 eV and refractive index from 2.20 to 2.37 with the increase of substrate temperature from 303 to 673 K. Copyright (c) 2012 John Wiley & Sons, Ltd.

A Novel Fiber Bragg Grating Based Sensing Methodology for Direct Measurement of Surface Strain on Body Muscles during Physical Exercises

The present work proposes a new sensing methodology, which uses Fiber Bragg Gratings (FBGs) to measure in vivo the surface strain and strain rate on calf muscles while performing certain exercises. Two simple exercises, namely ankle dorsi-flexion and ankle plantar-flexion, have been considered and the strain induced on the medial head of the gastrocnemius muscle while performing these exercises has been monitored. The real time strain generated has been recorded and the results are compared with those obtained using a commercial Color Doppler Ultrasound (CDU) system. It is found that the proposed sensing methodology is promising for surface strain measurements in biomechanical applications.

Physical ageing in Se-Te-Sb glasses

Bulk Se60-xTe40Sbx glasses in the composition range 0 <= x <= 14 were prepared by the melt quenching method. Differential Scanning Calorimetric (DSC) and thermal crystallization studies were performed to understand the thermodynamic property like glass transition and structural transformations. These glasses exhibit sharp endothermic peak at the glass transition (T-g). Disappearance of the endothermic peak at T-g in the rejuvenated samples clearly indicates the ageing effect in these glasses. Addition of Sb to Se-Te increases the connectivity of the structural network which is evidenced from the increase in T-g. A distinct change in the slope of the T-g at x=6, indicates a major change in the way the network is connected. The glass forming ability and the thermal stability also exhibit a maximum at x=6. T-g increases with the ageing time and the corresponding fictive temperature (T-f) calculated from the specific heat curves shows a decreasing trend. The molecular movements along the polymeric Se chains might cause the structural relaxation and the physical ageing. The physical ageing effect has been understood on the basis of the Bond Free Solid Angle (BFSA) model proposed by Kastner. Thermally crystallized samples show the formation of rhombohedral Sb2Te3, rhombohedral Sb2Se3 and hexagonal Te phases.

Performance analysis of adaptive physical layer network coding for wireless two-way relaying

The performance analysis of adaptive physical layer network-coded two-way relaying scenario is presented which employs two phases: Multiple access (MA) phase and Broadcast (BC) phase. The deep channel fade conditions which occur at the relay referred as the singular fade states fall in the following two classes: (i) removable and (ii) non-removable singular fade states. With every singular fade state, we associate an error probability that the relay transmits a wrong network-coded symbol during the BC phase. It is shown that adaptive network coding provides a coding gain over fixed network coding, by making the error probabilities associated with the removable singular fade states contributing to the average Symbol Error Rate (SER) fall as SNR-2 instead of SNR-1. A high SNR upper-bound on the average end-to-end SER for the adaptive network coding scheme is derived, for a Rician fading scenario, which is found to be tight through simulations. Specifically, it is shown that for the adaptive network coding scheme, the probability that the relay node transmits a wrong network-coded symbol is upper-bounded by twice the average SER of a point-to-point fading channel, at high SNR. Also, it is shown that in a Rician fading scenario, it suffices to remove the effect of only those singular fade states which contribute dominantly to the average SER.

Influence of physical structure and chemistry of diesel soot suspended in hexadecane on lubrication of steel-on-steel contact

Soot generated from the combustion process in diesel engines affect engine tribology. In this paper, two diesel soot samples; from engine exhaust and oil filter are suspended in hexadecane oil and the suspension is used to lubricate a steel ball on steel flat sliding contact at a contact pressure of 1.3 GPa. The friction and wear of the steel flat are recorded. The data are compared with those recorded when the soot is generated by burning ethylene gas. The rationale for the comparatively poor tribology of diesel soot is explored by quantifying the size and shape of primary particles and agglomerates, hardness of single primary soot particles, the crystallinity and surface and near surface chemistry of soot and interparticle adhesion.

Growth-temperature dependent physical properties of SnS nanocrystalline thin films

In this article we have demonstrated the influence of growth-temperature on the morphology and orientation of SnS films deposited by thermal evaporation technique. While increasing the growth-temperature, the morphology of SnS films changed from flakes-like nanocrystals to regular cubes, whereas their orientation shifted from <111> to <040> direction. The chemical composition of SnS films gradually changed from sulfur-rich to tin-rich with the increase of growth-temperature. The structural analyzes reveal that the crystal structure of SnS films probably changes from orthorhombic to tetragonal at the growth-temperature of about 410 degrees C. Raman studies show that SnS films grown at all temperatures consist of purely SnS phase, whereas the optical studies reveal that the direct optical bandgap of SnS films decreased with the increase of growth-temperature. From these results it has been emphasized that the morphology and orientation along with electrical and optical properties of nearly stoichiometric SnS films strongly depend on their growth-temperature.