Studies on design, fabrication and reliability assessment of embedded passives on a high-density interconnect (HDI) organic substrate using a sequential build-up process

One of the foremost design considerations in microelectronics miniaturization is the use of embedded passives which provide practical solution. In a typical circuit, over 80 percent of the electronic components are passives such as resistors, inductors, and capacitors that could take up to almost 50 percent of the entire printed circuit board area. By integrating passive components within the substrate instead of being on the surface, embedded passives reduce the system real estate, eliminate the need for discrete and assembly, enhance electrical performance and reliability, and potentially reduce the overall cost. Moreover, it is lead free. Even with these advantages, embedded passive technology is at a relatively immature stage and more characterization and optimization are needed for practical applications leading to its commercialization.This paper presents an entire process from design and fabrication to electrical characterization and reliability test of embedded passives on multilayered microvia organic substrate. Two test vehicles focusing on resistors and capacitors have been designed and fabricated. Embedded capacitors in this study are made with polymer/ceramic nanocomposite (BaTiO3) material to take advantage of low processing temperature of polymers and relatively high dielectric constant of ceramics and the values of these capacitors range from 50 pF to 1.5 nF with capacitance per area of approximately 1.5 nF/cm(2). Limited high frequency measurement of these capacitors was performed. Furthermore, reliability assessments of thermal shock and temperature humidity tests based on JEDEC standards were carried out. Resistors used in this work have been of three types: 1) carbon ink based polymer thick film (PTF), 2) resistor foils with known sheet resistivities which are laminated to printed wiring board (PWB) during a sequential build-up (SBU) process and 3) thin-film resistor plating by electroless method. Realization of embedded resistors on conventional board-level high-loss epoxy (similar to 0.015 at 1 GHz) and proposed low-loss BCB dielectric (similar to 0.0008 at > 40 GHz) has been explored in this study. Ni-P and Ni-W-P alloys were plated using conventional electroless plating, and NiCr and NiCrAlSi foils were used for the foil transfer process. For the first time, Benzocyclobutene (BCB) has been proposed as a board level dielectric for advanced System-on-Package (SOP) module primarily due to its attractive low-loss (for RF application) and thin film (for high density wiring) properties.Although embedded passives are more reliable by eliminating solder joint interconnects, they also introduce other concerns such as cracks, delamination and component instability. More layers may be needed to accommodate the embedded passives, and various materials within the substrate may cause significant thermo -mechanical stress due to coefficient of thermal expansion (CTE) mismatch. In this work, numerical models of embedded capacitors have been developed to qualitatively examine the effects of process conditions and electrical performance due to thermo-mechanical deformations.Also, a prototype working product with the board level design including features of embedded resistors and capacitors are underway. Preliminary results of these are presented.

Relative ability of ovine follicle stimulating hormone and its beta-subunit to generate antibodies having bioneutralization potential in nonhuman primates

The relative ability of ovine follicle stimulating hormone and its beta-subunit, two potential candidates for male contraceptive vaccine, to generate antibodies in monkeys capable of bioneutralizing follicle stimulating hormone was assessed using in vitro model systems. Antiserum against native ovine follicle stimulating hormone was found to be highly specific to the intact form with no cross-reactivity with either of the two subunits while the antiserum against beta-subunit of follicle stimulating hormone could bind to the beta-subunit in its free form as well as when it is combined with alpha-subunit to form the intact hormone. Both antisera could block the binding of the hormone to the receptor if the hormone was preincubated with the antibody. However, the follicle stimulating hormone beta-antisera could only inhibit the binding of the hormone partially (33 percent inhibition) if the antibody and receptor were mixed prior to the addition of the hormone, while antisera to the native follicle stimulating hormone could block the binding completely (100 percent inhibition) in the same experiment. Similarly antisera to the native follicle stimulating hormone was significantly effective in blocking (100 percent) response to follicle stimulating hormone but not the beta-subunit antisera (0 percent) as checked using an in vitro granulosa cell system. Thus the probability of obtaining antibodies of greater bioneutralization potential is much higher if intact hormone is used as an antigen rather than its beta-subunit as a vaccine.

Nature of corrosive and abrasive wear in ball mill grinding

Laboratory results of marked-ball wear tests are used to discuss the relative significance of corrosive and abrasive wear in wet grinding. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion current obtained from polarization curves under abrasion. Slurry rheology governs the manner in which ground slurries coat grinding balls, thereby influencing not only the grinding efficiency but also abrasive wear. The effects of percent solids and a grinding aid are illustrated.

An algorithm to find distant repeats in a pair of protein sequences

Distant repeats between a pair of protein sequences can be exploited to study the various aspects of proteins such as structure-function relationship, disorders due to protein malfunction, evolutionary analysis, etc. An in-depth analysis of the distant repeats would facilitate to establish a stable evolutionary relation of the repeats with respect to their three-dimensional structure. To this effect, an algorithm has been devised to identify the distant repeats in a pair of protein sequences by essentially using the scores of PAM (Percent Accepted Mutation) matrices. The proposed algorithm will be of much use to researchers involved in the comparative study of various organisms based on the amino-acid repeats in protein sequences. (C) 2010 Elsevier B.V. All rights reserved.

Studies on nucleotidases in plants: Fluorescence and kinetic properties of nucleotide pyrophosphatase from mung bean (Phaseolus aureus) seedlings

Nucleotide pyrophosphatase of mung bean seedlings has earlier been isolated in our laboratory in a dimeric form (Mr 65,000) and has been shown to be converted to a tetramer by AMP and to a monomer by p-hydroxymercuribenzoate. All the molecular forms were enzymatically active with different kinetic properties. By a modified procedure using blue-Sepharose affinity chromatography, we have now obtained a dimeric form of the enzyme which is desensitized to AMP interaction. The molecular weight of the desensitized form of the enzyme was found to be the same as that of the native dimeric enzyme. However, the desensitized enzyme functioned with a linear time course, contrary to the biphasic time course exhibited by the native enzyme. In addition, it was not converted to a tetramer on the addition of AMP, had only one binding site for adenine nucleotides, and p-hydroxy-mercuribenzoate had no effect on the time course of the reaction or on the molecular weight of the enzyme. The temperature optimum of the desensitized enzyme was found to be 67 °C in contrast to the optimum of 49 °C for the native dimer. Fifty percent of the tryptophan residues of the desensitized enzyme were not accessible for quenching by iodide. Fluorescence studies gave Kd values of 0.34, 2.2, and 0.8 mImage for AMP, ADP, and ATP, which were close to the Ki values of 0.12, 2.2, and 0.9 mImage , respectively, for these nucleotides. The binding and inhibition studies with AMP and its analogs showed that the 6-amino group and the 5′-phosphate group were essential for the inhibition of the enzyme activity.

Characterization, electrical percolation and magnetization studies of polystyrene/multiwall carbon nanotube composite films

Polystyrene/multiwall carbon nanotube composite films are prepared with loading up to 7 weight percent (wt%) of multiwall carbon nanotubes by solution processing and casting technique. In the formation of these composite films, iron filled carbon nanotubes with high aspect ratio (similar to 4000) were used. Scanning electron microscopy study shows that the nanotubes are uniformly dispersed within the polymer matrix. At high magnification, bending of carbon nanotubes is noticed which can be attributed to their elastic properties. The electrical conductivity measurements show that the percolation threshold is rather low at 0.21 wt%. Hysteresis loop measurements on the bulk multiwall carbon nanotube and composite samples are done at 10, 150 and 300 K and the coercivity values are found to be largest at all the temperatures, for 1 wt% composite sample. (C) 2010 Elsevier B.V. All rights reserved.

Thermal decomposition of ethylene diamine diperchlorate

Thermal decomposition of ethylene diamine diperchlorate (EDDP) has been studied by differential-thermal analysis (DTA), thermogravimetric analysis (TGA), isothermal weight-loss measurements and mass-spectrometric analysis of the decomposition products. It has been observed that EDDP decomposes in two temperature regions. The low-temperature decomposition stops at about 35 to 40 percent weight loss below 250°C. The reason for the low-temperature cessation may be the adsorption of excess ethylene diamine on the crystal surface of EDDP. An overall activation energy of 54 kcal per mole has been calculated for the thermal decomposition of EDDP. Mass-spectrometric analysis shows that the decomposition products are mainly CO2, H2O, HCl and N2. The following stoichiometry has been proposed for the thermal decomposition of EDDP: (−CH2NH3CIO4)2→2CO2O+2HCl+N2

A method for estimation of the radius of elastic-plastic boundary around cold-worked holes

The radius of an elastic-plastic boundary was measured by the strain gage method around the cold-worked region in L72-aluminum alloy. The relative radial expansion was varied from 2.5 to 6.5 percent during the cold-working process using mandrel and split sleeve. The existing theoretical studies in this area are reviewed. The experimental results are compared with existing experimental data of various investigators and with various theoretical formulations. A model is developed to predict the radius of elastic-plastic boundary, and the model is assessed by comparing with the present experiments.

Mechanical Properties of Al-Mica Particulate Composite Material

Cast aluminium alloy mica particle composites of varying mica content were tested in tension, compression, and impact. With 2.2 percent mica (size range 40µm – 120µm) the tensile and compression strengths of aluminium alloy decreased by 56 and 22 percent, respectively. The corresponding decreases in percent elongation and percent reduction are 49 and 39 percent. Previous work [2] shows that despite this decrease in strength the composite with 2.5 percent mica and having an UTS of 15 kg/mm2 and compression strength of 28 kg/mm2 performs well as a bearing material under severe running conditions. The differences in strength characteristics of cast aluminium-mica particle composites between tension and compression suggests that, as in cast iron, expansion of voids at the matrix particle interface may be the guiding mechanism of the deformation. SEM studies show that on the tensile fractured specimen surface, there are large voids at the particle matrix interface.

Laboratory studies on ball wear in the grinding of a hematite-magnetite ore

Marked-ball grinding tests were carried out under different grinding conditions and environments. Three types of balls were used, namely, cast hyper steel, high chrome cast iron and EN-31 (forged), which cover a wide range of chemical composition, microstructure and media hardness. The effect of pulp density on ball wear and grinding efficiency was also studied. Relative pulp viscosities at different percent solids for the ore slurry were also determined. As the Kudremukh ore contained about 0.2% pyrite, the effect of addition of pyrite on ball wear was studied separately. Results of marked-ball grinding tests indicated that ball wear increased with time and showed a sharp increase for wet grinding over dry grinding. Ball wear under wet grinding conditions was also influenced by the gaseous atmosphere in the mill. At 70% solids, the best results in terms of reduced ball wear coupled with satisfactory grinding efficiency were obtained. The influence of oxygen on the corrosive wear of grinding balls was increasingly felt only if sulphide minerals such as pyrite were also present in the ore. The various ball materials could be arranged in the following order with respect to their overall wear resistance: high chrome cast iron > EN-31 (forged) > cast hyper steel.Possible ball wear mechanisms involved in the grinding of Kudremukh ore are discussed.

Broadband stacked three-layer circular microstrip antenna arrays

The broadband aspects of stacked three-layer electromagnetically coupled circular microstrip antenna arrays are investigated experimentally. Experiments carried out on 8-element linear microstrip antenna arrays, using optimized stacked three-layer circular microstrip antenna elements, configured in E- and H-planes, have exhibited an impedance bandwidth of 20 percent, with a high gain and a good pattern shape with sidelobe as well as crosspolarization levels better than -20 dB through a scan angle of 40 deg from the broadside.

Effect of a specific estrogen antibody on pregnancy establishment in the bonnet monkey (Macaca radiata)

The requirement for estrogen for pregnancy establishment has not been conclusively demonstrated in primates. Selective neutralization of estrogens was achieved in mated female monkeys during preimplantation and postimplantation periods by injecting characterized estrogen antiserum from either day 14 to 18 or day 28 to 32 of cycle. While estrogen deprivation during preimplantation period in 5 animals exposed to 14 ovulatory cycles resulted in only one pregnancy, only 3 of 13 monkeys treated during postimplantation period continued pregnancy to term. In comparison with controls (4 of 5 monkeys becoming pregnant), the percent protection against pregnancy in animals treated during preimplantation period was 93. The pregnancy termination in 10 of 13 monkeys treated during postimplantation period when compared with normal postimplantation pregnancy wastage in our colony (2%) is also highly significant (P less than 0.01). The present study demonstrates a critical need for estrogen during the peri-implantation period for a successful pregnancy establishment in primates.

Indian Ocean Dipole: Processes and impacts

Equatorial Indian Ocean is warmer in the east, has a deeper thermocline and mixed layer, and supports a more convective atmosphere than in the west. During certain years, the eastern Indian Ocean becomes unusually cold, anomalous winds blow from east to west along the equator and southeastward off the coast of Sumatra, thermocline and mixed layer lift up and the atmospheric convection gets suppressed. At the same time, western Indian Ocean becomes warmer and enhances atmospheric convection. This coupled ocean-atmospheric phenomenon in which convection, winds, sea surface temperature (SST) and thermocline take part actively is known as the Indian Ocean Dipole (IOD). Propagation of baroclinic Kelvin and Rossby waves excited by anomalous winds, play an important role in the development of SST anomalies associated with the IOD. Since mean thermocline in the Indian Ocean is deep compared to the Pacific, it was believed for a long time that the Indian Ocean is passive and merely responds to the atmospheric forcing. Discovery of the IOD and studies that followed demonstrate that the Indian Ocean can sustain its own intrinsic coupled ocean-atmosphere processes. About 50% percent of the IOD events in the past 100 years have co-occurred with El Nino Southern Oscillation (ENSO) and the other half independently. Coupled models have been able to reproduce IOD events and process experiments by such models – switching ENSO on and off – support the hypothesis based on observations that IOD events develop either in the presence or absence of ENSO. There is a general consensus among different coupled models as well as analysis of data that IOD events co-occurring during the ENSO are forced by a zonal shift in the descending branch of Walker cell over to the eastern Indian Ocean. Processes that initiate the IOD in the absence of ENSO are not clear, although several studies suggest that anomalies of Hadley circulation are the most probable forcing function. Impact of the IOD is felt in the vicinity of Indian Ocean as well as in remote regions. During IOD events, biological productivity of the eastern Indian Ocean increases and this in turn leads to death of corals over a large area.Moreover, the IOD affects rainfall over the maritime continent, Indian subcontinent, Australia and eastern Africa. The maritime continent and Australia suffer from deficit rainfall whereas India and east Africa receive excess. Despite the successful hindcast of the 2006 IOD by a coupled model, forecasting IOD events and their implications to rainfall variability remains a major challenge as understanding reasons behind an increase in frequency of IOD events in recent decades.

A new perovskite series based on lanthanum chromite [LaCr1−xMxO3−δ]

A new series of substituted perovskites of the type LaCr1−xMxO3−δ, where M=Cu or Mg have been synthesised by the citrate gel process and characterized by means of powder X-ray diffraction, infrared spectroscopy, selected area diffraction and also by electron paramagnetic resonance spectroscopy. The general powder morphology was also observed using scanning electron microscopy. 40 mole percent substitution of Cr3+ by Cu2+ or Mg2+ have shown to result in single phase perovskite structure. Beyond x=0.5, a new phase has been identified in a narrow compositional range. Effect of Cu and Mg substitution on the sinterability of pure LaCrO3 has also been studied. It is possible to get near theoretically dense materials at a temperature as low as 1200°C in air by copper substitution.

Top-spin analysis of new scalar and tensor interactions in e(+)e(-) collisions with beam polarization

We utilize top polarization in the process e(+)e(-) -> t (t) over bar at the International Linear Collider ( ILC) with transverse beam polarization to probe interactions of the scalar and tensor type beyond the standard model and to disentangle their individual contributions. Ninety percent confidence level limits on the interactions with realistic integrated luminosity are presented and are found to improve by an order of magnitude compared to the case when the spin of the top quark is not measured. Sensitivities of the order of a few times 10(-3) TeV-2 for real and imaginary parts of both scalar and tensor couplings at root s = 500 and 800 GeV with an integrated luminosity of 500 fb(-1) and completely polarized beams are shown to be possible. A powerful model-independent framework for inclusive measurements is employed to describe the spin-momentum correlations, and their C, P, and T properties are presented in a technical appendix.