Steroids and related natural products. VIII. Synthesis of oxasteroids

Peroxydisulfuric acid oxidation of testosterone propionate, progesterone, and cholest-4-en-3-one has been shown to yield 3-oxo-17β-hydroxy-4-oxa-5α-androstane (I, after saponification), 3,20-dioxo-4-oxa-5α-pregnane (V) and 3-oxo-4-oxa-5α-cholestane (VII) respectively. Boron trifluoride etherate-lithium aluminum hydride reduction of δ-lactones I, V, and VII led to the corresponding tetrahydropyran derivatives (IIb, VIa, and VIII). Similar reduction of 3β-hydroxy-17-oxo-17a-oxa-D-homo-5α-androstane (XI) gave 3β-hydroxy-17a-oxa-D-homo-5α-androstane (XIIa). Diborane-boron trifluoride etherate was also found to reduce lactones to cyclic ethers, while reduction with diborane gave hemiacetals. Evidence in support of the structures and stereochemistry assigned to the lactones and their unusual reduction products has been summarized. A tentative mechanism is proposed for lactone → ether reduction employing diborane-boron trifluoride etherate.

Steroids and related natural products. VII. Boron trifluoride etherate-lithium aluminum hydride reduction of smilagenin acetate

Reduction of smilagenin acetate (Va) using a boron trifluoride etherate-lithium aluminum hydride reagent, followed by hydrogen peroxide oxidation and acetylation, was found to yield: 3β-ethoxysmilagenin (Vb), 3β-ethoxydihydrosmilagenin acetate (VIa), dihydrosmilagenin diacetate (VIb), and a complex mixture of partially acetylated products. Similar reaction conditions were employed to convert dihydrodiosgenin (II) to dihydrochlorogenin (III). Boron trifluoride etherate-lithium aluminum hydride reduction of 3β-acetoxy-5α-cholestane and 3β-acetoxy-5α-lanostane (VIIIa) was shown to yield the corresponding 3β-ethoxy (e.g., VIIIb) derivatives.

Distribution of products around a burning droplet: an analytical approach

A knowledge of the concentration distribution around a burning droplet is essential if accurate estimates are to be made of the transport coefficients in that region which influence the burning rate. There are two aspects of this paper; (1) determination of the concentration profiles, using the simple assumption of constant binary diffusion coefficients for all species, and comparison with experiments; and (2) postulation of a new relation for the therinal conductivity, which takes into account the variations of both temperature and concentrations of various species. First, the theoretical concentration profiles are evaluated and compared with experimental results reported elsewhere [5]. It is found that the agreement between the theory and experiment is fairly satisfactory. Then, by the use of these profiles and the relations proposed in the literature for the thermal conductivity of a mixture of nonpolar gases, a new relation for thermal conductivity: K = (A1 + B1 T) + (A2 + B2 T) xr (21). is suggested for analytical solutions of droplet combustion problems. Equations are presented to evaluate A1, A2, B1, and B2, and values of these terms for a few hydrocarbons are tabulated.

Dry sliding wear behavior of Al2O3 fiber reinforced aluminum composites

Dry sliding wear behavior of die-cast ADC12 aluminum alloy composites reinforced with short alumina fibers were investigated by using a pin-on-disk wear tester. The Al2O3 fibers were 4 mu m in diameter and were present in volume fractions (T-f)ranging from 0.03 to 0.26, The length of the fiber varied from 40 to 200 mu m. Disks of aluminum-alumina composites were rubbed against a pin of nitrided stainless steel SUS440B with a load of 10 N at a sliding velocity of 0.1 m/s. The unreinforced ADC 12 aluminum alloy and their composites containing low volume fractions of alumina (V-f approximate to 0.05) showed a sliding-distance-dependent transition from severe to mild wear. However, composites containing high volume fractions of alumina ( V-f > 0.05) exhibited only mild wear for all sliding distances. The duration of occurrence of the severe wear regime and the wear rate both decrease with increasing volume fraction. In MMCs the wear rate in the mild wear regime decreases with increase in volume fraction: reaching a minimum value at V-f = 0.09 Beyond V-f = 0.09 the wear rate increasesmarginally. On the other hand, the wear rate of the counterface (steel pin) was found to increase moderately with increase in V-f. From the analysis of wear data and detailed examination of (a) worn surfaces, (b) their cross-sections and (c) wear debris, two modes of wear mechanisms have been identified to be operative, in these materials and these are: (i) adhesive wear in the case of unreinforced matrix material and in MMCs with low Vf and (ii) abrasive wear in the case of MMCs with high V-f. (C) 2000 Elsevier Science Ltd. All rights reserved.

Voltage delay during constant-current or constant-resistance discharge of Mg-MnO2 dry cells: A comparative study

A theoretical approach has been developed to relate the voltage delay transients of the Mg-MnO2 dry cell observed during discharge by two commonly employed modes, viz., (1) at constant current, and (2) across a constant resistance. The approach has been verified by comparison of experimentally obtained transients with those generated from theory. The method may be used to predict the delay parameters of the Mg-MnO2 dry cell under the two modes of discharge and can, in principle, be extended to lithium batteries.

Determination of free elemental sulphur in some petroleum products

Uncombined elemental sulphur in petroleum products such as kerosene, diesel, furnace and gear oil has been determined by conversion into copper(I) sulphide at 150–170°. The copper(I) sulphide can be weighed, or its sulphur content determined by the iodimetric method.

Changes to near-surface region of PTFE during dry sliding against steel

PTFE specimens were slid against an EN24 disc. The unworn and worn surfaces as well as the wear debris were examined by X-ray diffraction. Sliding was found to introduce (i) shrinkage of the unit cell, (ii) enlargement of crystallites and (iii) residual stresses in the slid PTFE surface. No conformational changes in the 157 helix could be observed due to sliding. The wear debris was found to be 1 mgrm thick warped laminates.

Reactions of bis(isonitrosoethylacetoacetato)palladium(II) with straight chain aliphatic primary amines influence of concentration of the reacting amines on the nature of the products

Reactions of bis(isonitrosoethylacetoacetato)palladium(II), Pd(IEAA)2,with straight chain non-bulky alkylamines, RNH2(R = CH3, C2H5, n-C3H7or n-C4H9) in the mole ratio 1:1 gave bis (B-alkylisonitrosoethylacetoacetateimino)Palladium(II), Pd(R-IEAI)2. In this reaction the coordinated carbonyl groups of Pd(IEAA)2 undergo condensation with amines fo rming Schiff bases (>CNR). On the other hand, the reactions of Pd(IEAA)2 with a large excess of amine yielded N-alkylamido bridgedisonitrosoethylacetoacetatedipalladium(II), μ-(NHR)2[Pd(IEAA)]2 complexes. The complexes are characterized by elemental analyses, magnetic susceptib ility, i.r., p.m.r. and in some cases, nitrogen 1s X-ray photoelectron and mass spectral studies.

Equivalent circuit parameters of the film-covered magnesium/electrolyte interface in Mg/MnO2 dry cells from transient and ac impedance measurements

The electrochemical properties of the film-covered anode/solution interface in the magnesium/ manganese dioxide dry cell have been evaluated. The most plausible electrical equivalent circuit description of the Mg/solution interface with the passive film intact, has been identified. These results are based on the analysis of ac impedance and voltage transient measurements made on the dry cell under conditions which cause no damage to the protective passive film on the anode. The study demonstrates the complementary character of impedance and transient measurements when widely different frequency ranges are sampled in each type of investigation. The values and temperature dependence of the anode-film resistance, film capacitance, double-layer capacitance and charge-transfer resistance of the film-covered magnesium/solution interface have been determined. The magnitude of these values and its implications in understanding the important performance aspects of the magnesium/manganese dioxide dry cell are discussed. The study may be extended, in principle, to Li, Al and Ca batteries.