A new methodology for realizing magnification of holographic images

The article describes a new method for obtaining a holographic image of desired magnification, consistent with the stipulated criteria for its resolution and aberrations.

Structural adaptability in the system Bi2O3 --- WO3 : Higher members of the homologous series Bi2WnO3n+3

The ultramicrostructure of phases with n = 1, 2 and 3 in the hypothetical series Bi2WnO3n+3 has been investigated by high resolution electron microscopy and energy dispersive X-ray emission spectroscopy. For n = 1 and 2, well ordered phases with the predicted compositions have been obtained, but for n = 3, a severely disordered assemblage containing intergrowths of the two known structures and strips of the n = 3 member is produced. No evidence for ordered structures with n > 2 has yet been obtained.

Fracture Behavior of Multidirectional DCB Specimen: Higher-Order Beam Theories

Mathematical models, for the stress analysis of symmetric multidirectional double cantilever beam (DCB) specimen using classical beam theory, first and higher-order shear deformation beam theories, have been developed to determine the Mode I strain energy release rate (SERR) for symmetric multidirectional composites. The SERR has been calculated using the compliance approach. In the present study, both variationally and nonvariationally derived matching conditions have been applied at the crack tip of DCB specimen. For the unidirectional and cross-ply composite DCB specimens, beam models under both plane stress and plane strain conditions in the width direction are applicable with good performance where as for the multidirectional composite DCB specimen, only the beam model under plane strain condition in the width direction appears to be applicable with moderate performance. Among the shear deformation beam theories considered, the performance of higher-order shear deformation beam theory, having quadratic variation for transverse displacement over the thickness, is superior in determining the SERR for multidirectional DCB specimen.

Estimation of higher natural frequencies of polar orthotropic annular plates

A method based on an assumption that the radial bending moment is zero at a nodal circle is shown to yield accurate estimates of natural frequencies corresponding to higher modes of transversely vibrating polar orthotropic annular plates for various combinations of clamped, simply supported and free edge conditions. This method is found to be convenient for the determination of locations of nodal circles as well. Numerical investigations revealed that for small holes, nodal circles tend to move towards the outer edge with increasing number of nodal diameters. For large holes, it has been shown that the plate behaves like a long rectangular strip.

Estimation of higher natural frequencies of polar orthotropic annular plates

A method based on an assumption that the radial bending moment is zero at a nodal circle is shown to yield accurate estimates of natural frequencies corresponding to higher modes of transversely vibrating polar orthotropic annular plates for various combinations of clamped, simply supported and free edge conditions. This method is found to be convenient for the determination of locations of nodal circles as well. Numerical investigations revealed that for small holes, nodal circles tend to move towards the outer edge with increasing number of nodal diameters. For large holes, it has been shown that the plate behaves like a long rectangular strip.

On Minimization of Peak Power for Scan Circuit during Test

Scan circuit generally causes excessive switching activity compared to normal circuit operation. The higher switching activity in turn causes higher peak power supply current which results into supply, voltage droop and eventually yield loss. This paper proposes an efficient methodology for test vector re-ordering to achieve minimum peak power supported by the given test vector set. The proposed methodology also minimizes average power under the minimum peak power constraint. A methodology to further reduce the peak power below the minimum supported peak power, by inclusion of minimum additional vectors is also discussed. The paper defines the lower bound on peak power for a given test set. The results on several benchmarks shows that it can reduce peak power by up to 27%.

Recognition of Interaction Interface Residues in Low-Resolution Structures of Protein Assemblies Solely from the Positions of C alpha Atoms

Background: The number of available structures of large multi-protein assemblies is quite small. Such structures provide phenomenal insights on the organization, mechanism of formation and functional properties of the assembly. Hence detailed analysis of such structures is highly rewarding. However, the common problem in such analyses is the low resolution of these structures. In the recent times a number of attempts that combine low resolution cryo-EM data with higher resolution structures determined using X-ray analysis or NMR or generated using comparative modeling have been reported. Even in such attempts the best result one arrives at is the very course idea about the assembly structure in terms of trace of the C alpha atoms which are modeled with modest accuracy. Methodology/Principal Findings: In this paper first we present an objective approach to identify potentially solvent exposed and buried residues solely from the position of C alpha atoms and amino acid sequence using residue type-dependent thresholds for accessible surface areas of C alpha. We extend the method further to recognize potential protein-protein interface residues. Conclusion/Significance: Our approach to identify buried and exposed residues solely from the positions of C alpha atoms resulted in an accuracy of 84%, sensitivity of 83-89% and specificity of 67-94% while recognition of interfacial residues corresponded to an accuracy of 94%, sensitivity of 70-96% and specificity of 58-94%. Interestingly, detailed analysis of cases of mismatch between recognition of interface residues from C alpha positions and all-atom models suggested that, recognition of interfacial residues using C alpha atoms only correspond better with intuitive notion of what is an interfacial residue. Our method should be useful in the objective analysis of structures of protein assemblies when positions of only C alpha positions are available as, for example, in the cases of integration of cryo-EM data and high resolution structures of the components of the assembly.

Fuzzy waste load allocation model: a multiobjective approach

Fuzzy Waste Load Allocation Model (FWLAM), developed in an earlier study, derives the optimal fractional levels, for the base flow conditions, considering the goals of the Pollution Control Agency (PCA) and dischargers. The Modified Fuzzy Waste Load Allocation Model (MFWLAM) developed subsequently is a stochastic model and considers the moments (mean, variance and skewness) of water quality indicators, incorporating uncertainty due to randomness of input variables along with uncertainty due to imprecision. The risk of low water quality is reduced significantly by using this modified model, but inclusion of new constraints leads to a low value of acceptability level, A, interpreted as the maximized minimum satisfaction in the system. To improve this value, a new model, which is a combination Of FWLAM and MFWLAM, is presented, allowing for some violations in the constraints of MFWLAM. This combined model is a multiobjective optimization model having the objectives, maximization of acceptability level and minimization of violation of constraints. Fuzzy multiobjective programming, goal programming and fuzzy goal programming are used to find the solutions. For the optimization model, Probabilistic Global Search Lausanne (PGSL) is used as a nonlinear optimization tool. The methodology is applied to a case study of the Tunga-Bhadra river system in south India. The model results in a compromised solution of a higher value of acceptability level as compared to MFWLAM, with a satisfactory value of risk. Thus the goal of risk minimization is achieved with a comparatively better value of acceptability level.

Disease burden due to Streptococcus dysgalactiae subsp equisimilis (group G and C streptococcus) is higher than that due to Streptococcus pyogenes among Mumbai school children

Streptococcus pyogenes [group A streptococcus (GAS)], a human pathogen, and Streptococcus dysgalactiae subsp. equisimilis [human group G and C streptococcus (GGS/GCS)] are evolutionarily related, share the same tissue niche in humans, exchange genetic material, share up to half of their virulence-associated genes and cause a similar spectrum of diseases. Yet, GGS/GCS is often considered as a commensal bacterium and its role in streptococcal disease burden is under-recognized. While reports of the recovery of GGS/GCS from normally sterile sites are increasing, studies describing GGS/GCS throat colonization rates relative to GAS in the same population are very few. This study was carried out in India where the burden of streptococcal diseases, including rheumatic fever and rheumatic heart disease, is high. As part of a surveillance study, throat swabs were taken from 1504 children attending 7 municipal schools in Mumbai, India, during 2006-2008. GAS and GGS/GCS were identified on the basis of beta-haemolytic activity, carbohydrate group and PYR test, and were subsequently typed. The GGS/GCS carriage rate (1166/1504, 11%) was eightfold higher than the GAS carriage (22/1504, 1.5%) rate in this population. The 166 GGS/GCS isolates collected represented 21 different emm types (molecular types), and the 22 GAS isolates represented 15 different emm types. Although the rate of pharyngitis associated with GGS/GCS is marginally lower than with GAS, high rates of throat colonization by GGS/GCS underscore its importance in the pathogenesis of pharyngitis.

Energy identities in water wave theory for free-surface boundary condition with higher-order derivatives

A modified form of Green's integral theorem is employed to derive the energy identity in any water wave diffraction problem in a single-layer fluid for free-surface boundary condition with higher-order derivatives. For a two-layer fluid with free-surface boundary condition involving higher-order derivatives, two forms of energy identities involving transmission and reflection coefficients for any wave diffraction problem are also derived here by the same method. Based on this modified Green's theorem, hydrodynamic relations such as the energy-conservation principle and modified Haskind–Hanaoka relation are derived for radiation and diffraction problems in a single as well as two-layer fluid.

Stereochemical Analysis of Higher α,α-Dialkylglycine Containing Peptides. Characterization of Local Helical Conformations at Dipropylglycine Residues and Observation of a Novel Hydrated Multiple β-Turn Structure in Crystals of a Glycine Rich Peptide

The peptide Boc-Gly-Dpg-Gly-Gly-Dpg-Gly-NHMe (1) has been synthesized to examine the conformational preferences of Dpg residues in the context of a poor helix promoting sequence. Single crystals of 1 were obtained in the space group P21/c with a = 13.716(2) Å, b = 12.960(2) Å, c = 22.266(4) Å, and β = 98.05(1)°; R = 6.3% for 3660 data with |Fo| > 4σ. The molecular conformation in crystals revealed that the Gly(1)-Dpg(2) segment adopts φ, ψ values distorted from those expected for an ideal type II‘ β-turn (φGly(1) = +72.0°, ψGly(1) = −166.0°; φDpg(2) = −54.0°, ψDpg(2) = −46.0°) with an inserted water molecule between Boc-CO and Gly(3)NH. The Gly(3)-Gly(4) segment adopts φ, ψ values which lie broadly in the right handed helical region (φGly(3) = −78.0°, ψGly(3) = −9.0°; φGly(4) = −80.0°, ψGly(4) = −18.0°). There is a chiral reversal at Dpg(5) which takes up φ, ψ values in the left handed helical region. The Dpg(5)-Gly(6) segment closely resembles an ideal type I‘ β-turn (φDpg(5) = +56.0°, ψDpg(5) = +32.0°; φGly(6) = +85.0°, ψGly(6) = −3.0°). Molecules of both chiral senses are found in the centrosymmetric crystal. The C-terminus forms a hydrated Schellman motif, with water insertion into the potential 6 → 1 hydrogen bond between Gly(1)CO and Gly(6)NH. NMR studies in CDCl3 suggest substantial retention of the multiple turn conformation observed in crystals. In solution the observed NOEs support local helical conformation at the two Dpg residues.

Paper chromatography of higher fatty acids

An attempt has been made to review the literature that has accumulated during the last twelve years on the subject of paper chromatography of higher fatty acids. The various modifications that have been applied to the technique have been considered and their merits and limitations discussed. The important modifications are mainly concerned with the stationary and mobile phases and the use of different reagents for identification and estimation. This technique has also been successfully applied to the quantitative determination of the components of "critical pairs" of fatty acids in biological materials.

Application of reversed phase circular paper chromatography to the analysis of higher fatty acids

A detailed study of various reversed phase systems for the qualitative analysis of fatty acids has been made and it has been shown, among other things, that the liquid paraffin-aqueous methanol system is a most convenient one. The details of a fairly simple and rapid method for the quantitative estimation of higher fatty acids have also been discussed.

Solution cation-binding properties of segmented polyethylene oxide-A C-13 NMR spectroscopic study

Two segmented polyethylene oxides, SPEO-3 and SPEO-4, were prepared using a novel transetherification methodology. Their structures were confirmed by H-1 and C-13 NMR spectroscopy. The complexation of these SPEO's with alkali-metal ions in solution was investigated by C-13 NMR spectroscopy. The mole-fraction method was used to determine the complexation ratio of SPEO with LIClO4 at 25 degrees C, which showed that these formed 1:1 (polymer repeat unit/salt) complexes. The association constant, K, for the complex formation was calculated from the variation of the chemical shift values with salt concentration, using a standard nonlinear least-square fitting procedure. The maximum change in chemical shift (Delta delta) and the K values suggest that both SPEO-3 and SPEO-4 formed stronger complexes with lithium salts than with sodium salts. Unexpectedly, the K values were found to be different, when the variation of delta of different carbons was used in the fitting procedure. This suggests that several possible complexed species may be in equilibrium with the uncomplexed one. Structurally similar model compounds were also prepared and their complexation studies indicated that all of them also formed 1:1 complexes with Li salts. Interestingly, it was observed that the polymers gave higher K values suggesting the formation of more stable complexes in polymers when compared to the model analogues. (C) 2000 John Wiley & Sons, Inc.

A course for teaching design research methodology

Design research informs and supports practice by developing knowledge to improve the chances of producing successful products.Training in design research has been poorly supported. Design research uses human and natural/technical sciences, embracing all facets of design; its methods and tools are adapted from both these traditions. However, design researchers are rarely trained in methods from both the traditions. Research in traditional sciences focuses primarily on understanding phenomena related to human, natural, or technical systems. Design research focuses on supporting improvement of such systems, using understanding as a necessary but not sufficient step, and it must embrace methods for both understanding reality and developing support for its improvement. A one-semester, postgraduate-level, credited course that has been offered since 2002, entitled Methodology for Design Research, is described that teaches a methodology for carrying out research into design. Its steps are to clarify research success; to understand relevant phenomena of design and how these influence success; to use this to envision design improvement and develop proposals for supporting improvement; to evaluate support for its influence on success; and, if unacceptable, to modify, support, or improve the understanding of success and its links to the phenomena of design. This paper highlights some major issues about the status of design research and describes how design research methodology addresses these. The teaching material, model of delivery, and evaluation of the course on methodology for design research are discussed.