Determination of free elemental sulphur in some petroleum products

Uncombined elemental sulphur in petroleum products such as kerosene, diesel, furnace and gear oil has been determined by conversion into copper(I) sulphide at 150–170°. The copper(I) sulphide can be weighed, or its sulphur content determined by the iodimetric method.

Thermodynamics of Phosphorus and Sulphur Removal during Basic Oxygen Steelmaking

Removal of impurity elements from hot metal is essential in basic oxygen steelmaking. Oxidation of phosphorus from hot metal has been studied by several authors since the early days of steelmaking. Influence of different parameters on the distribution of phosphorus, seen during the recent work of the authors, differs somewhat from that reported earlier. On the other hand, removal of sulphur during steelmaking has drawn much less attention. This may be due to the magnitude of desulphurisation in oxygen steelmaking being relatively low and desulphurisation during hot metal pre-treatment or in the ladle furnace offering better commercial viability Further, it is normally accepted that sulphur is removed to steelmaking slag in the form of sulphide only However, recent investigations have indicated that a significant amount of sulphur removed during basic oxygen steelmaking can exist in the form of sulphate in the slag under oxidising conditions. The distribution of sulphur during steelmaking becomes more important in the event of carry-over of sulphur-rich blast-furnace slag, which increases sulphur load in the BOF. The chemical nature of sulphur in this slag undergoes a gradual transition from sulphide to sulphate as the oxidative refining progresses.

Oxidation of aqueous sulphur dioxide catalysed by poly-4-vinylpyridine-Cu(II) complex .2. Combined homogeneous and heterogeneous phase oxidation

Aqueous phase oxidation of sulphur dioxide at low concentrations catalysed by a PVP-Cu complex in the solid phase and dissolved Cu(II) in the liquid phase is studied in a rotating catalyst basket reactor (RCBR). The equilibrium adsorption of Cu(II) and S(VI) on PVP particles is found to be of the Langmuir-type. The diffusional effects of S(IV) species in PVP-Cu resin are found to be insignificant whereas that of product S(VI) are found to be significant. The intraparticle diffusivity of S(VI) is obtained from independent tracer experiments. In the oxidation reaction HSO3- is the reactive species. Both the S(IV) species in the solution, namely SO2(aq) and HSO3- get adsorbed onto the active PVP-Cu sites of the catalyst, but only HSO3- undergoes oxidation. A kinetic mechanism is proposed based on this feature which shows that SO2(aq) has a deactivating effect on the catalyst. A rate model is developed for the three-phase reaction system incorporating these factors along with the effect of concentration of H2SO4 on the solubility of SO2 in the dilute aqueous solutions of Cu(II). Transient oxidation experiments are conducted at different conditions of concentration of SO2 and O-2 in the gas phase and catalyst concentration, and the rate parameters are estimated from the data. The observed and calculated profiles are in very good agreement. This confirms the deactivating effect of nonreactive SO2(aq) on the heterogeneous catalysis.

Quasichemical equations for oxygen and sulphur in liquid binary alloys

An equation has been derived for predicting the activity coefficient of oxygen or sulphur in dilute solution in binary alloys, based on the quasichemical approach, where the metal atoms and the oxygen atoms are assigned different bond numbers. This equation is an advance on Alcock and Richardson's earlier treatment where all the three types of atoms were assigned the same coordination number. However, the activity coefficients predicted by this new equation appear to be very similar to those obtained through Alcock and Richardson's equation for a number of alloy systems, when the coordination number of oxygen in the new model is the same as the average coordination number used in the earlier equation. A second equation based on the formation of “molecular species” of the type XnO and YnO in solution is also derived, where X and Y atoms attached to oxygen are assumed not to make any other bonds. This equation does not fit experimental data in all the systems considered for a fixed value of n. Howover, if the strong oxygen-metal bonds are assumed to distort the electronic configuation around the metal atoms bonded to oxygen and thus reduce the strength of the bonds formed by these atoms with neighbouring metal atoms by approximately a factor of two, the resulting equation is found to predict the activity coefficients of oxygen that are in good agreement with experimental data in a number of binary alloys.

Some studies on a solid state sulphur probe for coal gasification system

Measurements on the solid electrolyte cell(Ar -b H2 ~ H2S/CaS + CaF2 ~- ( P t ) / / C a F 2 / / ( P t )-~- CaF2 ~ CaS/H2S ~- H2 ~- At) show that the emf of the cell is directly related through the Nernst equation to the difference in sulfur potentials established at the two Ar ~- H2 ~ H2S/electrode interfaces. The electrodes are designed to convert the sulfur potential gradient across the calcium fluoride electrolyte into an equivalent fluorine potential gradient with the aid of the reaction, CaF2(s) ~ 1~ S2(g)-e CaS(s) ~- F2(g). The response time of the probe varies from approximately 9 hr at 990~ to 2.5 hr at 1225~ The conversion of calcium sulfide and/or calcium fluoride into calcium oxide should not be a problem in anticipated commercial coal gasification systems. Suggestions are presented for improving the cell for such commercial applications.

Sulphur potential measurements with a two phase sulphide oxide electrolyte

The open circuit potentials of the galvanic cell,Pt (or Au)¦(Ar + H2S + H2)primeparCaS + ZrO2(CaO)par (Ar + H2S+ H2)Prime£t (or Au) has been measured in the temperature range 1000 to 1660 K and PH2S:PH 2 ratios from 1.73×10–5 to 2.65×10–1. The solid electrolyte consists of a dispersion of calcium sulphide in a matrix of calcia-stabilized zirconia. The surface of the electrolyte is coated with a thin layer of calcium sulphide to prevent the formation of water vapour by reaction of hydrogen sulphide with calcium oxide or zirconia present in the electrolyte. The use of a lsquopoint electrodersquo with a catalytically active tip was necessary to obtain steady emfs. At low temperatures and high sulphur potentials the emfs agreed with the Nernst equation. Deviations were observed at high temperatures and low sulphur potentials, probably due to the onset of significant electronic conduction in the oxide matrix of the electrolyte. The values of oxygen and sulphur potentials at which the electronic conductivity is equal to ionic conductivity in the two-phase electrolyte have been evaluated from the emf response of the cell. The sulphide-oxide electrolyte is unsuitable for sulphur potential measurements in atmospheres with high oxygen potentials, where oxidation of calcium sulphide may be expected.

Elastic Properties Of Sulphur And Selenium Doped Ternary PbTe Alloys By First Principles

Lead telluride (PbTe) is an established thermoelectric material which can be alloyed with sulphur and selenium to further enhance the thermoelectric properties. Here, a first principles study of ternary alloys PbSxTe(1-x) and PbSexTe(1-x) (0 <= x <= 1) based on the Virtual Crystal Approximation (VCA) is presented for different ratios of the isoelectronic atoms in each series. Equilibrium lattice parameters and elastic constants have been calculated and compared with the reported data. Anisotropy parameter calculated from the stiffness constants showed a slight improvement in anisotropy of elastic properties of the alloys over undoped PbTe. Furthermore, the alloys satisfied the predicted stability criteria from the elastic constants, showing stable structures, which agreed with the previously reported experimental results.

Ultra-small sulphur nanoparticles configured inside a flexible organic mixed conducting network as a cathode for lithium-sulphur batteries

The major challenges in Li-S batteries are the formation of soluble polysulphides during the reversible conversion of S-8 <-> Li2S, large changes in sulphur particle volume during lithiation and extremely poor charge transport in sulphur. We demonstrate here a novel and simple strategy to overcome these challenges towards practical realization of a stable high performance Li-S battery. For the first time, a strategy is developed which does away with the necessity of pre-fabricated high surface area hollow-structured adsorbates and also multiple nontrivial synthesis steps related to sulphur loading inside such adsorbates. A lithiated polyethylene glycol (PEG) based surfactant tethered on ultra-small sulphur nanoparticles and wrapped up with polyaniline (PAni) (abbreviated as S-MIEC) is demonstrated here as an exceptional cathode for Li-S batteries. The PEG and PAni network around the sulphur nanoparticles serves as an efficient flexible trap for sulphur and polysulphides and also provides distinct pathways for electrons (through PAni) and ions (through PEG) during battery operation. Contrary to the cathodes demonstrated based on various carbon-sulphur composites, the mixed conducting S-MIEC showed an extremely high loading of 75%. The S-MIEC exhibited a stable capacity of nearly 900 mA h g(-1) at the end of 100 cycles at a 1C current rate.

Microstructural evolution and mechanical characteristics in nanocrystalline nickel with a bimodal grain-size distribution

An attractive microstructural possibility for enhancing the ductility of high-strength nanocrystals is to develop a bimodal grain-size distribution, in which the fine grains provide strength, and the coarser grains enable strain hardening. Annealing of nanocrystalline Ni over a range of temperatures and times led to microstructures with varying volume fractions of coarse grains and a change in texture. Tensile tests revealed a drastic reduction in ductility with increasing volume fraction of coarse grains. The reduction in ductility may be related to the segregation of sulphur to grain boundaries.

Using lead sulphate instead of lead oxide in flux growth of yttrium iron garnet(YIG) crystals

Crystal growth of YIG from fluxes containing lead sulphate in place of lead oxide in the usual lead oxide-lead fluoride-boron oxide flux system has been tried. Lead sulphate decomposes during crystal growth giving lead oxide and sulphur trioxide. Due to the influence of sulphur trioxide in the system the yield of crystals almost doubles. There is no change either in the morphology of the crystals or their lattice parameter. It is possible that solubility of YIG is different in the new flux and the changed solubility causes the increase in yield of crystals.

Structure Of 5'-Deoxy-5',6-Epithio-5,6-Dihydro-2',3'-O-Isopropylideneuridine, C12h16n2o5s

Mr=300.33 , triclinic, P1, a=5.635 (2), b=11.077(2), c=11.582(2)A, a= 70.48 (1), fl= 88.16 (3), y=80.56(3) ° , V= 670.325 A3, Z=2, D x = 1.49 Mg m -3, Cu Ka, n= 1.54184 ,A, g = 2.308mm -1, F(000)=316, T=301K, R=0.054, R w = 0.093 for 1944 observed counter reflections. The sulphur position with respect to the dihydrouracil ring, which is of possible relevance to the action of thymidylate synthetase, is axial in molecule A and equatorial in B. Both molecules show the anti conformation about the glycosidic bond [torsion angle C(6)-N(1)-C(1')-O(4'), 2'CN = 21.6 (9) and 29.4 (10) °] and have the C(4')-endo, O(4')-exo (40T) sugar conformation. The dioxolane-ring conformation is O(2')-endo in A and C(7)-endo in B. The dihydrouracil rings show self base pairing with hydrogen bondsN(3A)...O(ZB) and N(3B)...O(ZA).

Morphological structure of bismuth-doped n-type amorphous germanium sulphide semiconductors

Recent observation of n-type conduction in amorphous Ge20Ss_xBix at large bismuth concentrations (x = 11), which otherwise shows p-type conduction, has aroused considerable interest in the international scientific community [1]. The mechanism of such impurity incorporation in a germanium chalcogenide glass is not understood and is a topic of current interest. In our recent publications [2-10] we have brought to light some hitherto unknown and interesting features of bismuth dopants in chalcogen-rich Ge-X (X -- S, Se) glassy compositions. In this communication we present our new results of investigations on vitreous semiconductors Ge20S80 Bi using electron microscopy, electron diffraction of as-prepared and annealed/pressure quenched compositions. Our results provide conclusive support to the formation of composite clusters containing all the three elements, germanium, sulphur and bismuth, which crystallize in simpler stoichiometric compounds Bi2S3 and GeS2.

Structure of a thionucleoside: 5'-deoxy-5',6-epithio-5,6-dihydro-2',3'-O-isopropylidene-3-methyluridine

C13HlsN205 S, M r = 314.35, orthorhombic, P212121 with a = 39.526 (4), b = 6.607 (2), c = 5.661 (2) A, Z = 4, V = 1478.36 A 3, D c = 1.412 Mg m -3, Cu Ka radiation. Final R = 0.073 for 1154 observed counter reflections. The sulphur atom is in a pseudo-equatorial position with respect to the dihydrouracil ring. The sugar pucker is predominantly O(l')-exo unlike the C(3')-exo,C(4')-endo observed for 2',3'-O-isopropylideneuridine (ISPU). The fivemembered dioxolane ring has C(7) displaced by 0.497 (7)A from the best plane through atoms 0(2'), C(2'), C(3'), 0(3'), in contrast to ISPU where 0(3') shows the maximum deviation.