Raman spectra of addition compounds of glycine (diglycine hydrochloride, diglycine hydrobromide and diglycine nitrate)

Raman spectra of single crystals of diglycine hydrochloride, diglycine hydrobromide and diglycine nitrate have been recorded for the first time. λ 2536·5 resonance radiation of mercury has been used as exciter. The spectrum of diglycine hydrochloride exhibits 10 low frequency lines and 41 lines due to internal oscillations, while that of diglycine hydrobromide exhibits 11 lines and 41 lines respectively. In the case of diglycine nitrate 46 lines have been recorded, of which 10 belong to the lattice spectrum. These spectra are compared with the Raman spectra of triglycine sulphate and α-glycine and proper assignments have been given to the internal oscillations.

Effect of copper addition on the fracture and fatigue crack growth behavior of solution heat-treated SUS 304H austenitic steel

Small additions of Cu to the SUS 304H, a high temperature austenitic stainless steel, enhance its high temperature strength and creep resistance. As Cu is known to cause embrittlement, the effect of Cu on room temperature mechanical properties that include fracture toughness and fatigue crack threshold of as-solutionized SUS 304H steel were investigated in this work. Experimental results show a linear reduction in yield and ultimate strengths with Cu addition of up to 5 wt.% while ductility drops markedly for 5 wt.% Cu alloy. However, the fracture toughness and the threshold stress intensity factor range for fatigue crack initiation were found to be nearly invariant with Cu addition. This is because the fracture in this alloy is controlled by the debonding from the matrix of chromium carbide precipitates, as evident from fractography. Cu, on the other hand, remains either in solution or as nano-precipitates and hence does not influence the fracture characteristics. It is concluded that small additions of Cu to 304H will not have adverse effects on its fracture and fatigue behavior. (C) 2010 Elsevier B.V. All rights reserved.

Increasing ionic conductivity of polymer-sodium salt complex by addition of a non-ionic plastic crystal

Ionic conductivity and other physico-chemical properties of a soft matter composite electrolyte comprising of a polymer-sodium salt complex and a non-ionic plastic crystal are discussed here. The electrolyte under discussion comprises of polyethyleneoxide (PEO)-sodium triflate (NaCF3SO3) and succinonitrile (SN). Addition of SN to PEO-NaCF3SO3 resulted in significant enhancement in ionic conductivity. At 50% SN concentration (with respect to weight of polymer), the polymer-plastic composite electrolyte room temperature (= 25 degrees C) ionic conductivity was similar to 1.1 x 10(-4) Omega(-1) cm(-1), approximately 45 times higher than PEO-NaCF3SO3. Observations from ac-impedance spectroscopy along with X-ray diffraction, differential scanning calorimetry and Fourier transform inrared spectroscopy strongly suggest the enhancement in the composite is ionicconductivity due to enhanced ion mobility via decrease in crystallinity of PEO. The free standing composite polymer-plastic electrolytes were more compliable than PEO-NaCF3SO3 thus exhibiting no detrimental effects of succinonitrile addition on the mechanical stability of PEO-NaCF3SO3. We propose that the exploratory PEO-NaCF3SO3-SN system.discussed here will eventually be developed as a prototype electrolyte.for sodium-sulfur batteries capable of operating at ambient and.sub-ambient conditions. (C) 2010 Elsevier B.V. All rights reserved.

A study of the electronic structures of n---v addition compounds of BH3 by a combined use of ups and eels

Orbital energies and electronic transition energies of BH3·H2S and BH3·CO obtained from ultraviolet (HeI) photoelectron spectroscopy and electron energy loss spectroscopy are discussed in the light of quantum mechanical calculations. BH3·H2O has been characterized, for the first time, by means of the HeI spectrum and the ionization energies assigned to the various orbitals based on calculations.

Photochemistry of .alpha.,.beta.-unsaturated thiones: addition to electron-rich olefins from T1

1,1,3-Trimethyl-2-thioxo-1,2-dihydronaphthale(1n)e adds to electron-rich olefins upon excitation to either Sz (PP*) or Sl (ns*) states. Excitation to S2 level resulted in the same mixture of products, namely thietane and 1,4-dithiane, as on excitation to S1 level. Addition occurs to the thiocarbonyl function and not to the carbon-carbon double bond. The addition is site-specific, and the formation of thietane is regiospecific. The ratio of thietane to 1,4-dithiane in the product mixture is dependent on the concentration of the thioenone. The addition is suggested to originate from the lowest triplet state (Tl) and involves diradical intermediates.

Reactive hot pressing of ZrB2-ZrCx ultra-high temperature ceramic composites with the addition of SiC particulate

Starting with non-stoichiometric Zr-B4C powder mixture ZrB2-ZrC matrix composites with SiC particulate addition have been made. It was found that variable amounts (5-25 vol%) of SiC could be incorporated and reactively hot pressed (RHPed) to relative densities of 97-99% at 1400-1500 degrees C. This technique has the potential to fabricate ZrB2-based matrices at low temperatures with a variety of reinforcements whose composition and volume fraction are not limited by stoichiometric considerations. The hardness of the composites is in the range of 17-22 GPa. (C) 2010 Elsevier Ltd. All rights reserved.

Effect of magnesium addition and heat treatment on mild wear of hypoeutectic aluminium-silicon alloys

The effect of magnesium addition and subsequent heat treatment on mild wear of a cast hypoeutectic aluminium-silicon alloy when slid against EN 24 steel is studied. Morphology and chemistry of worn surface and subsurface are studied with a view to identify wear mechanism. Stability of an iron-aluminium mixed surface layer was found to be the key factor controlling wear resistance.

Purification and characterization of three toxins and two agglutinins from Abrus precatorius seed by using lactamyl-Sepharose affinity chromatography

Three toxins, abrin-I, -II, and -III, and two agglutinins, APA-I and -II, were purified from the seeds of Abrus precatorius by lactamyl-Sepharose affinity chromatography followed by gel filtration and DEAE-Sephacel column chromatography. abrin-I did not bind on DEAE-Sephacel column chromatography and the bound abrin-II, abrin-III, APA-I, and APA-II were eluted with a sodium acetate gradient. The identity of each protein was established by sodium dodecylsulfate-polyacrylamide gel electrophoresis and isoelectric focusing. The relative molecular weights are abrin-I, 64,000; abrin-II and abrin-III, 63,000 each: APA-I, 130,000; and APA-II, 128,000. Isoelectric focusing revealed microheterogeneity due to the presence of isoforms in each protein. Toxicity and binding studies further confirmed the differences among the lectins. The time course of inhibition of protein synthesis in thymocytes by the toxins showed lag times of 78, 61, and 72 min with Ki's of 0.55, 0.99, and 0.74 ms−1 at a 0.63 nImage concentration of each of abrin-I, -II, and -III, respectively. A Scatchard plot obtained from the equilibrium measurement for the lectins binding to lactamyl-Sepharose beads showed nonlinearity, indicating a cooperative mode of binding which was not observed for APA-I binding to Sepharose 4B beads. Further, by the criterion of the isoelectric focusing profile, it was shown that the least toxic abrin-I and the highly toxic abrin-II isolated by lactamyl-Sepharose chromatography were not retained on a low-affinity Sepharose 4B matrix, which signifies the necessity of using a high-affinity matrix for the purification of the lectins.

Room-temperature synthesis of gold nanoparticles - Size-control by slow addition

We report a simple and rapid process for the room-temperature synthesis of gold nanoparticles using tannic acid, a green reagent, as both the reducing and stabilising agent. We systematically investigated the effect of pH on the size distribution of nanoparticles synthesized. Based on induction time and zeta- potential measurements, we show that particle size distribution is controlled by a fine balance between the rates of reduction (determined by the initial pH of reactants) and coalescence (determined by the pH of the reaction mixture) in the initial period of growth. This insight led to the optimal batch process for size-controlled synthesis of 2-10 nm gold nanoparticles - slow addition (within 10 minutes) of chloroauric acid into tannic acid.

Direct Growth of Gold Nanorods on Gold and Indium Tin Oxide Surfaces: Spectral, Electrochemical, and Electrocatalytic Studies

The surfactant-assisted seed-mediated growth method was used for the formation of gold nanorods (GNRs) directly on gold (Au) and indium tin oxide (ITO) surfaces. Citrate-stabilized similar to 2.6 nm spherical gold nanoparticles (AuNPs) were first self-assembled on ITO or Au surfaces modified with (3-mercaptopropyl)-trimethoxysilane (MPTS) sol-gel film and then immersed in a cationic surfactant growth solution to form GNRs. The growth of GNRs on the MPTS sol gel film modified ITO surface was monitored by UV-visible spectroscopy. The ITO surface with the attached spherical AuNPs shows a surface plasmon resonance band at 550 nm. The intensity of this absorption band increases while increasing the immersion time of the AuNP-modified ITO surface into the growth solution, and after 5 h, an additional shoulder band around 680 nm was observed. The intensity of this shoulder band increases, and it was shifted to longer wavelength as the immersion time of the AuNP-modified ITO surface into the growth solution increases. After 20 h, a predominant wave at 720 nm was observed along with a band at 550 nm. Further immersion of the modified ITO surface into the growth solution did not change the absorption characteristics. The bands observed at 550 and 720 nm were characteristics of GNRs, corresponding to transverse and longitudinal waves, respectively. The AFM images showed the presence of GNRs on the surface of the MPTS sol gel modified ITO surface with a typical length of similar to 100-120 nm and a width of similar to 20-22 nm in addition to a few spherical AuNPs, indicating that seeded spherical AuNPs were not completely involved in the GNRs' formation. Finally, the electrocatalytic activity of the surface-grown GNRs on the MPTS sol gel film modified Au electrode toward the oxidation of ascorbic acid (AA) was studied. Unlike a polycrystalline Au electrode, the surface-grown GNR-modified electrode shows two well-defined voltammetric peaks for AA at 0.01 and 0.35 V in alkaline, neutral, and acidic pHs. The cause for the observed two oxidation peaks for AA was due to the presence of both nanorods and spherical nanoparticles on the electrode surface. The presence of spherical AuNPs on the MPTS sol gel film oxidized AA at more positive potential, whereas the GNRs oxidized AA at less positive potential. The observed 340 mV less positive potential shift in the oxidation of AA suggested that GNRs are better electrocatalysts for the oxidation of AA than the spherical AuNPs.

Addition of amines and halogens to fullerenes C60 and C70

In solution phase, aliphatic amines add on to fullerenes; vapourization of graphite in presence of methylamine gives nitrogeneous C60 derivatives. Reactions of C60 with SbCl5 and liquid Br2 yield halogen adducts.

Differential scanning calorimetry cure studies on the effect of addition of epoxy diluents of tetrafunctional epoxy resins

The effect of the addition of p-aminophenol and aniline-based epoxy diluents on the curing behavior of highly viscous tetraglycidyl diamino diphenyl methane resin with diamino diphenyl sulfone hardener have been investigated kinetically by differential scanning calorimetry. Dynamic scans were carried out over a temperature range 30–300°C for different resin formulations. Isothermal scans at four differnt temperatures have also been carried out for the evaluation of kinetic parameters. Heat flow measurements at different heating rates have indicated the evidence of autocatalytic behavior of curing reaction following a simple nth-order kinetics.

A near-optimal initial seed value selection in K-means means algorithm using a genetic algorithm

The K-means algorithm for clustering is very much dependent on the initial seed values. We use a genetic algorithm to find a near-optimal partitioning of the given data set by selecting proper initial seed values in the K-means algorithm. Results obtained are very encouraging and in most of the cases, on data sets having well separated clusters, the proposed scheme reached a global minimum.