Elasto-Electrostatic Analysis of Circular Microplates Used in Capacitive Micromachined Ultrasonic Transducers

The active structural component of a capacitive micromachined ultrasonic transducer (CMUT) is the top plate which vibrates under the influence of a time-varying electrostatic force thereby producing ultrasound waves of the desired frequency in the surrounding medium. Analysis of MEMS devices which rely on electrostatic actuation is complicated due to the fact that the structural deformations alter the electrostatic forces, which redistribute and modify the applied loads. Hence, it becomes imperative to consider the electrostatics-structure coupling aspect in the design of these devices. This paper presents an approximate analytical solution for the static deflection of a thin, clamped circular plate caused by electrostatic forces which are inherently nonlinear. Traditionally, finite element simulations using some commercial software such as ANSYS are employed to determine the structural deflections caused by electrostatic forces. Since the structural deformation alters the electrostatic field, a coupled-field simulation is required wherein the electrostatic mesh is continuously updated to coincide with the deflection of the structure. Such simulations are extremely time consuming, in addition to being nontransparent and somewhat hard to implement. We employ the classical thin-plate theory which is adequate when the ratio of the diameter to thickness of the plate is very large, a situation commonly prevalent in many MEMS devices, especially the CMUTs. We solve the thin-plate electrostatic-elastic equation using the Galerkin-weighted residual technique, under the assumption that the deflections are small in comparison to the thickness of the plate. The evaluation of the electrostatic force between the two plates is simplified due to the fact that the electrostatic gap is much smaller than the lateral dimensions of the device. The results obtained are compared to those found from ANSYS simulations and an excellent agreement is observed between the two. The pull-in voltage predicted by our model is close to the value predicted by ANSYS simulations.

Interaction of ecoP15I DNA methyltransferase with oligonucleotides containing the asymmetric sequence 5?-CAGCAG-3

EcoP15I DNA methyltransferase (Mtase) recognizes the asymmeteric sequence CAGCAG and catalyzes the transfer of a methyl group from S-adenosyl-L-methionine to the second adenine residue. We have investigated the DNA binding properties of EcoP15I DNA Mtase using gel mobility shift assays. EcoP15I DNA Mtase binds approximately threefold more tightly to DNA containing its recognition sequence, CAGCAG, than to non-specific sequences in the absence or presence of cofactors. Interestingly, in the presence of ATP the discrimination between specific and non-specific sequences increases significantly. These results suggest for the first time a role for ATP in DNA recognition by type III restriction-modification enzymes. In addition, we have shown that bromodeoxyuridine-containing oligonucleotides form complexes with EcoP15I DNA Mtase that are crosslinked upon irradiation. More importantly, we have shown that the crosslink site is at the site of DNA binding, since it can be suppressed by an excess of unmodified oligonucleotide. EcoP15I DNA Mtase exhibited Michaelis-Menten kinetics with both unmodified and bromodeoxyuridine-substituted DNA, with a higher specificity constant for the latter. Furthermore, gel mobility shift assays showed that proteolyzed EcoP15I DNA Mtase formed a specific complex with DNA, which had similar mobility as the native protein-DNA complex. Taken together these results form the basis fora detailed structure-function analysis of EcoP15I DNA Mtase.

Photolabeling of the EcoP15 DNA methyltransferase with S-adenosyl-l-methionine

Radioactivity from S-adenosyl-L-[methyl-H-3] methionine ([methyl-H-3]AdoMet) was bound to the EcoP15 DNA methyltransferase (M.EcoP15) following short-wave ultraviolet (UV) irradiation. The labeled protein was subjected to polyacrylamide-gel electrophoresis in the presence of sodium dodecyl sulfate (SDS-PAGE), and detected by fluorography and autoradiography. Labeling was found to be dependent on the concentration of AdoMet and time of UV irradiation. The photolabeling by [methyl-H-3]AdoMet was specific and blocked by S-adenosyl-L-homocysteine (AdoHcy) and sinefungin which are known to function as competitive inhibitors. Limited digestion of the M EcoP15-AdoMet adduct by Staphylococcus aureus protease V8 generated three peptides of approx. 50, 32 and 30 kDa; Interestingly, only the 30-kDa peptide fragment contained radioactivity, as detected by SDS-PAGE, followed by fluorography and autoradiography. Further, sequencing of a few amino acids at the N-terminus of these peptides showed that the 30-kDa fragment was the N-terminal portion of M.EcoP15, These results suggest that photolabeling is at the AdoMet-binding site and that the N-terminal half of M.EcoP15 may be involved in substrate binding.

Functional analysis of conserved motifs in EcoP15I DNA methyltransferase

EcoP15I DNA methyltransferase recognizes the sequence 5'-CAGCAG-3' and transfers a methyl group to N-6 of the second adenine residue in the recognition sequence. All N-6 adenine methyltransferases contain two highly conserved sequences, FxGxG (motif I), postulated to form part of the S-adenosyl-L-methionine binding site and (D/N/S)PP(Y/F) (motif IV) involved in catalysis. We have altered the second glycine residue in motif I to arginine and serine, and substituted tyrosine in motif IV with tryptophan in EcoP15I DNA methyltransferase, using site-directed mutagenesis. The mutant enzymes were overexpressed, purified and characterized by biochemical methods. The mutations in motif I completely abolished AdoMet binding but left target DNA recognition unaltered. Although the mutation in motif IV resulted in loss of enzyme activity, we observed enhanced crosslinking of S-adenosyl-L-methionine and DNA. This implies that DNA and AdoMet binding sites are close to motif IV. Taken together, these results reinforce the importance of motif I in AdoMet binding and motif IV in catalysis. Additionally, limited proteolysis and UV crosslinking experiments with EcoP15I DNA methyltransferase imply that DNA binds in a cleft formed by two domains in the protein. Methylation protection analysis provides evidence for the fact that EcoP15I DNA MTase makes contacts in the major groove of its substrate DNA. Interestingly, hypermethylation of the guanine residue next to the target adenine residue indicates that the protein probably flips out the target adenine residue. (C) 1996 Academic Press Limited

DNA recognition by the EcoP15I and EcoPI modification methyltransferases

The DNA-binding properties of the EcoP15I DNA methyltransferase (M . EcoP15I; MTase) were studied using electrophoretic mobility shift assays. We show by molecular size-exclusion chromatography and dimethyl suberimidate crosslinking that M . EcoP15I is a dimer in solution. While M . EcoP15I binds approx. threefold more tightly to its recognition sequence, 5'-CAGCAG-3', than to non-specific sequences in the presence of AdoMet or its analogs, the discrimination between specific and non-specific sequences significantly increases in presence of ATP. These results suggest for the first time a role for ATP in DNA recognition by type-III restriction-modification enzymes. Furthermore, we show that although c2 EcoPI mutant MTases are defective in AdoMet binding, they are still able to bind DNA in a sequence-specific manner.

Molecular self-assembly of cadmium-triazolate complexes via hydrogen bonding: Synthesis, structures and photoluminescent properties

Two new cadmium coordination polymers namely Cd(HAmTrz-COO)(4)(NH4+)(2)] 1; and Cd(HAmTrz)(2)I-2](n) 2; (HAmTrz-COOH = 3-amino-1,2,4-triazole-5-carboxylic acid), have been prepared based on HAmTrz-COOH as ligand. The crystal structures of 1 and 2 have been determined by single-crystal X-ray diffraction technique. In coordination-complex 1 four triazole ligands coordinate via N1 nitrogen leading to a tetrahedral geometry around cadmium ion, while in 2 the ligand prefers to coordinate to the metal in a bidentate bridging mode. The structures of both the coordination polymers can be envisaged as 3D hydrogen bonded networks. Thermogravimetric analysis shows that 2 is more stable than 1 owing to different coordination numbers of cadmium atoms. Photoluminescence properties of both the compounds have been investigated in the solid state. (C) 2011 Elsevier B.V. All rights reserved.

The Effect of Evacuated Backside Cavity on the Dynamic Characteristics of a Capacitive Micromachined Ultrasonic Transducer

In this paper, we investigate the effect of vacuum sealing the backside cavity of a Capacitive Micromachined Ultrasonic Transducer (CMUT). The presence or absence of air inside the cavity has a marked effect upon the system parameters, such as the natural frequency, damping, and the pull-in voltage. The presence of vacuum inside the cavity of the device causes a reduction in the effective gap height which leads to a reduction in the pull-in voltage. We carry out ANSYS simulations to quantify this reduction. The presence of vacuum inside the cavity of the device causes stress stiffening of the membrane, which changes the natural frequency of the device. A prestressed modal analysis is carried out to determine the change in natural frequency due to stress stiffening. The equivalent circuit method is used to evaluate the performance of the device in the receiver mode. The lumped parameters of the device are obtained and an equivalent circuit model of the device is constructed to determine the open circuit receiving sensitivity of the device. The effect of air in the cavity is included by incorporating an equivalent compliance and an equivalent resistance in the equivalent circuit.

Analytical Evaluation of Squeeze Film Forces in a CMUT With Sealed Air-Filled Cavity

The presence of vacuum inside the cavity of a capacitive micromachined ultrasonic transducer (CMUT) causes the membrane of the device (which is the main vibrating structural component) to deflect towards the substrate, thereby causing a reduction in the effective gap height. This reduction causes a drastic decrease in the pull-in voltage of the device limiting the DC bias at which the device can be operated for maximum efficiency. In addition, this initial deflection of the membrane due to atmospheric pressure, causes significant stress stiffening of the the membrane, changing the natural frequency of the device significantly from the design value. To circumvent the deleterious effects of vacuum in the sealed cavity, we investigate the possibility of using sealed CMUT cavities with air inside at ambient pressure. In order to estimate the transducer loss due to the presence of air in the sealed cavity, we evaluate the resulting damping and determine the forces acting on the vibrating membrane resulting from the compression of the trapped air film. We take into account the flexure of the top vibrating membrane instead of assuming the motion to be parallel-plate like. Towards this end, we solve the linearized Reynolds equation using the appropriate boundary conditions and show that, for a sealed CMUT cavity, the presence of air does not cause any squeeze film damping.

Geotechnical Characterization of Some Indian Bentonites for their Use as Buffer Material in Geological Repository

The present study examines the geotechnical properties of Indian bentonite clays for their suitability as buffer material in deep geological repository for high-level nuclear wastes. The bentonite samples are characterized for index properties, compaction, hydraulic conductivity and swelling characteristics. Evaluation of geotechnical properties of the compacted bentonite-sand admixtures, from parts of NW India reveals swelling potentials and hydraulic conductivities in the range of 55 % - 108 % and 1.2 X 10 –10 cm/s to 5.42x 10 –11 cm/s respectively. Strong correlation was observed between ESP (exchangeable sodium percentage) and liquid limit/swell potential of tested specimens. Relatively less well-defined trends emerged between ESP and swell pressure/hydraulic conductivity. The Barmer-1 bentonite despite possessing relatively lower montmorillonite content of 68 %, developed higher Atterberg limit and swell potential, and exhibited comparable swelling pressure and hydraulic conductivity as other bentonites with higher montmorillonite contents (82 to 86 %). The desirable geotechnical properties of Barmer clay as a buffer material is attributed to its large ESP (63 %) and, EMDD (1.17 Mg/m3) attained at the experimental compactive stress(5 MPa).

Structures of new crystal forms of Mycobacterium tuberculosis peptidyl-tRNA hydrolase and functionally important plasticity of the molecule

The X-ray structures of new crystal forms of peptidyl-tRNA hydrolase from M.similar to tuberculosis reported here and the results of previous X-ray studies of the enzyme from different sources provide a picture of the functionally relevant plasticity of the protein molecule. The new X-ray results confirm the connection deduced previously between the closure of the lid at the peptide-binding site and the opening of the gate that separates the peptide-binding and tRNA-binding sites. The plasticity of the molecule indicated by X-ray structures is in general agreement with that deduced from the available solution NMR results. The correlation between the lid and the gate movements is not, however, observed in the NMR structure.

Cation-templated 2-D Mn(II)-oxalate framework with an acyclic tetrameric water cluster

The single-crystal X-ray structure of a cation-templated manganese-oxalate coordination polymer [NH(C2H5)(3)][Mn-2(ox)(3)]center dot(5H(2)O)] (1) is reported. In 1, triethylammonium cation is entrapped between the cavities of 2-D honeycomb layers constructed by oxalate and water. The acyclic tetrameric water clusters and discrete water assemble the parallel 2-D honeycomb oxalate layers via an intricate array of hydrogen bonds into an overall 3-D network. The magnetic susceptibility, with and without the water cluster, are reported with infrared and EPR studies.

Climatic fluctuations during the LIA and post-LIA in the Kumaun Lesser Himalaya, India: Evidence from a 400 y old stalagmite record

This paper presents the first stable isotope (delta O-18 and delta C-13) data of a similar to 400 years (1590-2006 AD) long annual to decadal-resolution speleothem record collected from the Indian Lesser Himalaya. The data show a variation from -2.7 to -5.9 parts per thousand in delta O-18 and -5.3 to -8.8 parts per thousand in delta C-13. The isotopic analyses indicate that the climate during this period can be divided into two stages: a wet phase during the Little Ice Age (LIA) (1590-1850 AD) and comparatively dry phase during the post-LIA after 1850 AD. However, the record also documents the minor dry events during the LIA and a wet episode after the LIA. Within the age uncertainty, the dry spells during the LIA are linked with the historical drought events in the Indian subcontinent and similar latitudes. The isotopic record is consistent with a number of previous studies in the areas influenced by the Westerlies but appears to be conflicting to the regions, dominated by the Indian Summer Monsoon (ISM). This may be due to the possible changes in the strength of Westerlies in the study area and added by negative anomaly of North Atlantic Oscillation (NAO) during the LIA. (C) 2012 Elsevier Ltd and INQUA. All rights reserved.

Crystal Engineering in the Desiraju Research Group in Bangalore

Over the years, crystal engineering has transformed into a mature and multidisciplinary subject. New understanding, challenges, and opportunities have emerged in the design of complex structures and structure-property evaluation. Revolutionary pathways adopted by many leaders have shaped and directed this subject. In this short essay to celebrate the 60th birthday of Prof. Gautam R. Desiraju, we, his current research group members, contemplate the development of some of the topics explored by our group in the context of the overall subject. These topics, though not entirely new, are of significant interest to the crystal engineering community.

1-D Hydrogen bonded water in Cu(II)-picolinate coordination polymer: synthesis, crystal structure, and thermogravimetric analysis

A new Cu(II)-picolinate complex was synthesized and characterized by single crystal X-ray crystallography. The complex crystallizes in the centrosymmetric triclinic space group P (1) over bar (no. 2). Picolinate in the complex extends the neutral unit into a 1-D chain through mu(2)-bridging carboxylate. The complex has a hydrogen bonding acceptor in the second coordination sphere allowing lattice water to assemble neighboring chains. Water self-assembles to form a zig-zag 1-D chain. The adjacent chains are assembled by C-H center dot center dot center dot O interactions result in the formation 2-D hydrogen bonded network. The overall hydrogen bonding between water chain and Cu-picolinate network yields a 3-D hydrogen bonded coordination network. X-ray structural analysis, FTIR and thermal analysis have been used to characterize the reported compound in the solid state.