Axisymmetric melting of a long cylinder due to an infinite flux

By employing a new embedding technique, a short-time analytical solution for the axisymmetric melting of a long cylinder due to an infinite flux is presented in this paper. The sufficient condition for starting the instantaneous melting of the cylinder has been derived. The melt is removed as soon as it is formed. The method of solution is simple and straightforward and consists of assuming fictitious initial temperature for some fictitious extension of the actual region.

Analysis and computation of the oil film thickness between the piston ring and cylinder liner of an internal combustion engine

A study of the essential features of piston rings in the cylinder liner of an internal combustion engine reveals that the lubrication problem posed by it is basically that of a slider bearing. According to steady-flow-hydrodynamics, viz. Image the oil film thickness becomes zero at the dead centre positions as the velocity, U = 0. In practice, however, such a phenomenon cannot be supported by consideration of the wear rates of pistion rings and cylinder liners. This can be explained by including the “squeeze” action term in the

Stresses and Displacements under a Flexible Circular Foundation in the Presence of Friction or Adhesion

Die Vorliegende Arbeit beschäftigt sich mit den Spannungen und Verschiebungen an einem elastischen Halbraum unter einem kreisförmigen biegsamen Fundament, wenn an der Kontaktfläche vollkommenes Haften besteht. Das gemischte Randwertproblem wird mit Hilfe von Hankel-Transformationen auf duale Integralgleichungen von Titchmarsh- Typ zurückgeführt. Für die Berechnung der Spannungen und Verschiebungen werden Gaußsche Quadraturformeln benutzt. Die Ergebnisse werden mit denen verglichen, die man bei glattem Fundament erhält, und der Einfluß der Poisson-Zahl auf die Spannungen und Verschiebungen wird deutlich gemacht. Schließlich werden die Ergebnisse für den praktischen Gebrauch in Diagrammen und Tabellen zusammengefaßt.

Stresses and Displacements under a Flexible Circular Foundation in the Presence of Friction or Adhesion

Die Vorliegende Arbeit beschäftigt sich mit den Spannungen und Verschiebungen an einem elastischen Halbraum unter einem kreisförmigen biegsamen Fundament, wenn an der Kontaktfläche vollkommenes Haften besteht. Das gemischte Randwertproblem wird mit Hilfe von Hankel-Transformationen auf duale Integralgleichungen von Titchmarsh- Typ zurückgeführt. Für die Berechnung der Spannungen und Verschiebungen werden Gaußsche Quadraturformeln benutzt. Die Ergebnisse werden mit denen verglichen, die man bei glattem Fundament erhält, und der Einfluß der Poisson-Zahl auf die Spannungen und Verschiebungen wird deutlich gemacht. Schließlich werden die Ergebnisse für den praktischen Gebrauch in Diagrammen und Tabellen zusammengefaßt.

Axisymmetric deformation of a short magneto-strictive current-carrying cylinder

The title-problem has been reduced to that of solving a Fredholm integral equation of the second kind. One end of the cylinder is assumed to be fixed, while the cylinder is deformed by an axial current. The vertical displacement on the upper flat end of the cylinder has been determined from an iterative solution of the Fredholm equation valid for large values of the length. The radial displacement of the curved boundary has also been determined at the middle of the cylinder, by using the iterative solution.

Mechanics of transition in an axisymmetric laminar boundary layer on a circular cylinder

Measurements of the growth of artificially generated turbulent spots and intermittency distribution in the transition region on a circular cylinder in axial flow show that the instability Reynolds number of 11,000 has a marked effect on the properties. In particular, it is found that the spot production in the initial region when a single turbulent spot has not yet wrapped around the cylinder and the propagation is essentially two-dimensional, is significantly altered. But the transition in the downstream or latter region, where most of the turbulent spots propagate onedimensionally (like the turbulent plugs in a pipe), is not affected. When the radius Reynolds number is more than 11,000, the intermittency law in the initial region is essentially the same as in twodimensional flow on a flat plate and in the latter region it is the one-dimensional flow in a pipe, the demarcation between the two regions being quite sharp.

Stability of large flexible damped spacecraft modeled as elastic continua

Vibrational stability of a large flexible, structurally damped spacecraft subject to large rigid body rotations is analysed modelling the system as an elastic continuum. Using solution of rigid body attitude motion under torque free conditions and modal analysis, the vibrational equations are reduced to ordinary differential equations with time-varying coefficients. Stability analysis is carried out using Floquet theory and Sonin-Polya theorem. The cases of spinning and non-spinning spacecraft idealized as a flexible beam plate undergoing simple structural vibration are analysed in detail. The critical damping required for stabilization is shown to be a function of the spacecraft's inertia ratio and the level of disturbance.

A versatile and flexible digital pulse programmer for pulsed nuclear magnetic resonance

A versatile and flexible digital pulse programmer for two-pulse, three-pulse, saturation burst and Carr-Purcell sequences is described. Independently variable controls for pulse widths (0.2 mu s to 100 mu s), delay between pulses (0.2 mu s to 100 s) and for number of pulses (1 to 99) for the saturation burst and for the Carr-Purcell sequence, are brought to the front panel. The programmer can be used for one-shot experiments as well as for repetitive experiments.

Running-in wear of a compression ignition engine: Factors influencing the conformance between cylinder liner and piston rings

The conformance between the liner and rings of an internal combustion engine depends mainly on their linear wear (dimensional loss) during running-in. Running-in wear studies, using the factorial design of experiments, on a compression ignition engine show that at certain dead centre locations of piston rings the linear wear of the cylinder liner increases with increase in the initial surface roughness of the liner. Rough surfaces wear rapidly without seizure during running-in to promote quick conformance, so an initial surface finish of the liner of 0.8 μm c.l.a. is recommended. The linear wear of the cast iron liner and rings decreases with increasing load but the mass wear increases with increasing load. This discrepancy is due to phase changes in the cast iron accompanied by dimensional growth at higher thermal loads. During running-in the growth of cast iron should be minimised by running the engine at an initial load for which the exhaust gas temperature is approximately 180 °C.

Synthesis of ZnO Nanoneedles on Flexible Polymer Substrates at Room Temperature by Activated Reactive Evaporation

ZnO nanoneedles were successfully deposited on flexible polymer substrates at room temperature by activated reactive evaporation. Neither a catalyst nor a template was employed in this synthesis. These synthesized needles measured 500 - 600 nm in length and its diameter varied from 30 - 15 nm from the base to the tip. The single-crystalline nature of the nanoneedle was observed by high-resolution transmission electron microscopy studies. The Raman studies on these nanoneedles had shown that they are oxygen deficient in nature. A possible growth mechanism has been proposed here, in which the nanoneedles nucleate and grow in the gas phase by vapor-solid mechanism.

Effect of surface radiation on conjugate natural convection in a horizontal annulus driven by inner heat generating solid cylinder

This paper reports a numerical study of the laminar conjugate natural convection heat transfer with and without the interaction of the surface radiation in a horizontal cylindrical annulus formed between an inner heat generating solid circular cylinder and an outer isothermal circular boundary. Numerical solutions are obtained by solving the governing equations with a pressure correction method on a collocated (non-staggered) mesh. Steady-state results are presented for the flow and temperature distributions and Nusselt numbers for the heat generation based Grashof number ranging from 10(7) to 10(10), solid-to-fluid thermal conductivity ratios of 1, 5, 10, 50 and 100, radius ratios of 0.226 and 0.452 and surface emissivities of 0-0.8 with air as the working medium. It is observed that surface radiation reduces the convective heat transfer in the annulus compared to the pure natural convection case and enhances the overall Nusselt number.

Self-Assembly of a Pd-6-Molecular Double-Square and a Cu-3-Trigonalbipyramidal Cage via a New Tripodal Flexible Ligand

A new tripodal flexible ligand (L) containing pyrazolyl functionality has been prepared and successfully used to obtain a pd(6) (1) molecular double-square and a cu(3) trigonalbipyramidal cage (2), where complex 1 represents the first example of a double-square obtained using a flexible tripodal ligand.

Unsteady Natural Convection Flow over a Heated Cylinder Buried in a Fluid Saturated Porous Medium

Transient natural convection flow on a heated cylinder buried in a semi-infinite liquid-saturated porous medium has been studied. The unsteadiness in the problem arises due to the cylinder which is heated (cooled) suddenly and then maintained at that temperature. The coupled partial differential equations governing the flow and heat transfer are cast into stream function-temperature formulation, and the solutions are obtained from the initial time to the time when steady state is reached. The heat transfer is found to change significantly with increasing time in a small time interval immediately after the start of the impulsive change, and steady state is reached after some time. The average Nusselt number is found to increase with Rayleigh number When the surface of the cylinder is suddenly cooled, there is a change in the direction of the heat transfer in a small time interval immediately after the start of the impulsive change in the surface temperature;however when the surface temperature is suddenly increased, no such phenomenon is observed.

A real-time algorithm for simulation of flexible objects and hyper-redundant manipulators

Flexible objects such as a rope or snake move in a way such that their axial length remains almost constant. To simulate the motion of such an object, one strategy is to discretize the object into large number of small rigid links connected by joints. However, the resulting discretised system is highly redundant and the joint rotations for a desired Cartesian motion of any point on the object cannot be solved uniquely. In this paper, we revisit an algorithm, based on the classical tractrix curve, to resolve the redundancy in such hyper-redundant systems. For a desired motion of the `head' of a link, the `tail' is moved along a tractrix, and recursively all links of the discretised objects are moved along different tractrix curves. The algorithm is illustrated by simulations of a moving snake, tying of knots with a rope and a solution of the inverse kinematics of a planar hyper-redundant manipulator. The simulations show that the tractrix based algorithm leads to a more `natural' motion since the motion is distributed uniformly along the entire object with the displacements diminishing from the `head' to the `tail'.