Effect of Temperature on Respiration of a Mesophilic and a Thermophilic Fungus

The respiratory rates of mycelia of the mesophilic fungus, Aspergillus niger, and the thermophilic fungus, Thermomyces lanuginosus, were comparable at their respective temperature optima for growth. The respiratory rate of A. niger was independent of changes in temperature between 15 and 40 C. The respiratory rate of T. lanuginosus increased with increase in temperature between 25 and 55 C.

Studies of cryotreatment on the performance of integral diaphragm pressure transducers for space application

The integral diaphragm pressure transducers machined out of precipitation hardened martensite stainless steel (APX4) are widely used for propellant pressure measurements in space applications. These transducers are expected to exhibit dimensional stability and linearity for their entire useful life. These vital factors are very critical for the reliable performance and dependability of the pressure transducers. However, these transducers invariably develop internal stresses during various stages of machining. These stresses have an adverse effect on the performance of the transducers causing deviation from linearity. In order to eliminate these possibilities, it was planned to cryotreat the machined transducers to improve both the long-term linearity and dimensional stability. To study these effects, an experimental cryotreatment unit was designed and developed based on the concept of indirect cooling using the concept of cold nitrogen gas forced closed loop convection currents. The system has the capability of cryotreating large number of samples for varied rates of cooling, soaking and warm-up. After obtaining the initial levels of residual stress and retained austenite using X-ray diffraction techniques, the pressure transducers were cryotreated at 98 K for 36 h. Immediately after cryotreatment, the transducers were tempered at 510 degrees C for 3 h in vacuum furnace. Results after cryo treatment clearly indicated significant reduction in residual stress levels and conversion of retained austenite to martensite. These changes have brought in improvements in long term zero drift and dimensional stability. The cryotreated pressure transducers have been incorporated for actual space applications. (c) 2010 Published by Elsevier Ltd.

Impact of dust on solar photovoltaic (PV) performance: Research status, challenges and recommendations

The peaking of most oil reserves and impending climate change are critically driving the adoption of solar photovoltaic's (PV) as a sustainable renewable and eco-friendly alternative. Ongoing material research has yet to find a breakthrough in significantly raising the conversion efficiency of commercial PV modules. The installation of PV systems for optimum yield is primarily dictated by its geographic location (latitude and available solar insolation) and installation design (tilt, orientation and altitude) to maximize solar exposure. However, once these parameters have been addressed appropriately, there are other depending factors that arise in determining the system performance (efficiency and output). Dust is the lesser acknowledged factor that significantly influences the performance of the PV installations. This paper provides an appraisal on the current status of research in studying the impact of dust on PV system performance and identifies challenges to further pertinent research. A framework to understand the various factors that govern the settling/assimilation of dust and likely mitigation measures have been discussed in this paper. (C) 2010 Elsevier Ltd. All rights reserved.

Effect of pressure on the dielectric properties of DTAAP

Effect of pressure on the dielectric properties of ferroelectric DTAAP has been carried out upto about 4 Kbars. The dTc/dP value was found to be -1.65°C/Kbar. It was noted that the value of dTc/dP is 1.63 times smaller in DTAAP as compared to TAAP, where as Tc itself is 1.13 times larger.

Effect of V2O5 on the Surface and Structural Characteristics of Potassium Lithium Niobate

It has been suggested that materials with interesting and useful bulk non-linear optical properties might result by substituting vanadium, the lightest element in the group V of periodic table, for Nb or Ta atoms along with Li and three oxygens. It is with this motivation that we have been making attempts to grow single crystals of LiNbO3 doped with various concentrations of V2O5. Unfortunately the results obtained on the ceramic samples of this material have not been very encouraging, owing to their hygroscopic nature. However, our attempts to prepare both ceramic and single-crystalline samples of potassium lithium niobate (K3Li2Nb5O15; KLN) doped V2O5 were successful. In this letter we report the preliminary results concerning our studies on the effect of V2O5 doping on the structural as well as topographic features of both ceramic and single-crystalline samples of KLN.

Influence of microstructure on the wear of grinding media

Owing to the complexity of the wear process, high stress grinding abrasion is quite different from two-body abrasive wear. Reported data on two-body abrasive wear reveal that the wear decreases with an increase in steel hardness. This relationship can be established without having to consider the microstructure of the steel grinding medium. However, it is known that hardness cannot be directly employed to predict the wear of steel balls under three-body grinding abrasion, as occurs during dry grinding of ores in ball mills. The present work suggests that the wear behaviour of grinding balls can be classified according to the microstructural family to which they belong. Thus, in this work on AISI 52100 steel, the separate groups of microstructures were spheroidite—pearlite, bainite, tempered martensite and martensite with retained austenite. It appears that wear behaviour of the first three groups follows the same trend as that observed for two-body wear. The data suggest that an optimum level of retained austenite could improve the wear resistance of microstructures containing martensite.

Crystal structures of propanediamine complexed with L and DL- glutamic acid: effect of chirality on propanediamine.

The structures of complexes of 1,3-diaminopropane With L- and DL-glutamic acid have been determined. L-Glutamic acid complex: C3H12N22+.2C5H8NO4-, M(r) = 368.4, orthorhombic. P2(1)2(1)2(1), a = 5.199 (1), b = 16.832 (1). c = 20.076 (3) angstrom, V = 1756.6 (4) angstrom3, z = 4, D(x) = 1.39 g cm-3, lambda(Mo K-alpha) = 0.7107 angstrom, mu = 1.1 cm-1, F(000) = 792. T = 296 K, R = 0.044 for 1276 observed reflections. DL-Glutamic acid complex: C3H12N22+.2C5H8NO4-, M(r) = 368.4, orthorhombic, Pna2(1), a = 15.219(2), b = 5.169 (1), c 22.457 (4) angstrom, V = 1766.6 (5) angstrom3 Z = 4, D(x) = 1.38 g cm-3, lambda(Mo K-alpha) = 0.7107 angstrom, mu = 1.1 cm F(000) = 792, T = 296 K, R = 0.056 for 993 observed reflections. The conformation of diaminopropane is all-trans in the DL complex but trans-gauche in the L complex. The main packing feature in the L complex is the arrangement of diaminopropane around dimers of antiparallel L-glutamic acid molecules. The diaminopropane in the DL complex is sandwiched between two antiparallel glutamic acid molecules of the same chirality and this forms the basic packing unit. This might be the dominant form of interaction between L-glutamic acid and diaminopropane in solution. The structures reveal the adaptability of the polyamine backbone to different environments and the probable reasons for their choice as biological cations.

Structure and superconducting properties of Tl1?yPbyY1?xCaxSr2Cu2O7star, open: Dependence of Tc on hole concentration

Structure and superconducting properties of Tl1?yPbyY1?xCaxSr2Cu2O7 (y=0.0, 0.1, 0.25 and 0.5) , derived from the parent insulator TlYSr2Cu2O7, have been investigated for different values of x. XANES studies show Pb to be in the 4+ state while Tl is in the 3+ state, suggesting thereby that in this series, (x?y) approximately corresponds to the hole concentration. The in-plane Cu---O distance decreases with increase in x for all values of y. The apical Cu---O distance as well as the Tl(Pb)---O(2) distance show anomalies at x=0.5 in the series with y=0.25; at this composition, Tc also reaches a maximum. In general, the composition (value of x) at which the Tc of Tl1?yPbyY1?xCaxSr2Cu2O7 reaches a maximum depends on the Pb content and the maximum Tc itself increases with increase in y, reaching a value of 105 K at y=0.5. More interestingly, a maximum Tc occurs at an (x?y) value of not, vert, similar0.25, which is close to the hole concentration at maximum Tc in other cuprate superconductors containing two CuO2 layers.

Switching studies and the effect of irradiation on ferroelectric properties of TAAP and DTAAP

Polarization switching processes in TAAP and DTAAP have been studied by the Merz method. The switching process in DTAAP is slower than in TAAP. The temperature dependence of switching time indicates that the crystal might contain groups of domain nuclei with different activation energies. X-ray irradiation causes an increase in the threshold field below which switching could not occur and decrease in the mobility of domain walls. Irradiation decreases the peak value of dielectric constant, Tc and increases the value of coercive field. Domain structure studies on TAAP crystals have shown that the crystals grow as both predominantly single domain and multi domains, depending on which the internal bias increases or remains unaffected upon irradiation.

Influence of subcontracting on innovation and economic performance of SMEs in Indian automobile industry

Trans-national corporations (TNCs) expanding their production bases to developing countries having better conditions of manufacturing and domestic markets provide increasing opportunities for local small and medium enterprises (SMEs) to have subcontracting relationships with these TNCs Even though some theoretical and a few empirical studies throw light on the nature of assistance provided by TNCs to local SMEs through subcontracting relationships none of the studies so far quantitatively analysed the role of this assistance on the innovative performance of SMEs leading to better economic performance This paper probes the extent and diversity of assistance received by SMEs from a TNC through subcontracting and its influence on technological innovations and economic performance of SMEs in the Indian automobile industry Indian SMEs were able to receive mainly product related and purchase process assistance thereby implying that subcontracting is largely confined to purchase-supply relationships However assistance received through subcontracting is beneficial as It promoted technological innovations of SMEs the higher the degree of assistance the higher the level of innovations carried out by these SMEs which in turn facilitated their economic performance Thus this paper substantiates in the Indian context that subcontracting relationship with a TNC can be an important source of technological innovations and enhanced economic performance for SMEs (C) 2010 Elsevier Ltd All rights reserved