Polarization enhancement in compositionally graded vanadium doped bismuth titanate thin films

Compositionally up and downgraded Bi4-x/3Ti3-xVxO12 (x=0.0, 0.012,0.03, 0.06) thin films were grown on Pt coated silicon substrates by pulsed laser deposition technique. Downgraded fabrication showed improved ferroelectric polarization in comparison to upgraded fabrication. Films deposited at 650 and 700 degrees C showed very large remnant polarization (2P(r)) value of 82 mu C cm(-2), which is comparatively large among all bismuth based thin films reported so far. A mechanism based on vanadium enrich seeded layer formation in the downgraded structure is proposed for the improvement. Moreover, frequency independent behavior (100Hz-5kHz) of the graded films ensures its potential application for various microelectronic devices. (c) 2010 American Institute of Physics. [doi :10.1063/1.3431543].

Nature of Pb in superconducting cuprates containing lead: A Pb L3 x‐ray absorption near‐edge spectroscopy study

X‐ray absorption near‐edge spectroscopy studies show that Pb in superconducting Tl0.5Pb0.5CaSr2Cu2O7+δ is essentially in the 4+ state while it is in the 2+ state in Pb2Sr2Ca1−xLnxCu3O8+δ.

Elastic properties of phosphotungstate glasses

Elastic properties of potassium and lead phosphotungstate glasses have been investigated using ultrasonic velocity measurements. The composition dependence of elastic moduli in WO3-K2O-P2O5 glasses suggests that at low alkali oxide concentrations the atomic ring size increases by network modification, which results in the decrease of elastic moduli. In the highly modified regime, due to the presence of coulombic interaction, the rate of decrease of elastic moduli is reduced. In the WO3-PbO-P2O5 glasses the behaviour of elastic moduli suggests that PbO behaves both as a network former and network modifier. The incorporation of PbO into the network is quantitatively determined by the concentration of P2O5 in the system. The results are consistent with the structural model proposed earlier, based on characterization studies.

A modified least squares algorithm to treat associations in liquid alloys

The associated model for binary systems has been modified to include volume effects and excess entropy arising from preferential interactions between the associate and the free atoms or between the free atoms. Equations for thermodynamic mixing functions have been derived. An optimization procedure using a modified conjugate gradient method has been used to evaluate the enthalpy and entropy interaction energies, the free energy of dissociation of the complex, its temperature dependance and the size of the associate. An expression for the concentration—concentration structure factor [Scc (0)] has been deduced from the modified associated solution model. The analysis has been applied to the thermodynamic mixing functions of liquid Ga-Te alloys at 1120 K, believed to contain Ga2Te3 associates. It is observed that the modified associated solution model incorporating volume effects and terms for the temperature dependance of interaction energies, describes the thermodynamic properties of Ga-Te system satisfactorily.

Component Inventory Costs in an Assembly Problem with Uncertain Supplier Lead-Times

We present a generic study of inventory costs in a factory stockroom that supplies component parts to an assembly line. Specifically, we are concerned with the increase in component inventories due to uncertainty in supplier lead-times, and the fact that several different components must be present before assembly can begin. It is assumed that the suppliers of the various components are independent, that the suppliers' operations are in statistical equilibrium, and that the same amount of each type of component is demanded by the assembly line each time a new assembly cycle is scheduled to begin. We use, as a measure of inventory cost, the expected time for which an order of components must be held in the stockroom from the time it is delivered until the time it is consumed by the assembly line. Our work reveals the effects of supplier lead-time variability, the number of different types of components, and their desired service levels, on the inventory cost. In addition, under the assumptions that inventory holding costs and the cost of delaying assembly are linear in time, we study optimal ordering policies and present an interesting characterization that is independent of the supplier lead-time distributions.

Quantitation of serological cross-reactivity between two geographical isolates of Oryctes baculovirus by a modified ELISA

An assay was developed for quantitation of the antigenic relationship between viruses, by modification of the indirect ELISA. The principle of this method is to estimate the epitopes not shared between the related viruses, after titration of the antibodies specific to the common epitopes as in a blocking ELISA. In practice, varying concentrations of purified virus are preincubated with a fixed dilution of heterologous or homologous antiserum and the unbound antibodies present in the mixture are back titrated with virus particles bound to microtitre plates. The antigenic relationship is described in terms of differentiation index (DI) and total antigenic reactivity (TAR). This method has been used to quantitate cross-reactivity between two geographically different isolates of Oryctes baculovirus.

ESR studies of X-irradiated strontium mixed calcium tartrate crystals

The electron spin resonance spectra of X-ray irradiated single crystals of strontium doped calcium tartrate tetrahydrate (CST) with molecular formula Ca0.88Sr0.12C4H4O6.4H(2)O grown in gels has been investigated. Only one species of free radical but with two magnetically unequivalent sites was observed at room temperature. The free radical was found to be the result of the splitting of a C-II bond adjacent to both the hydroxyl and carboxyl groups. The a factor was found to be slightly anisotropic. Couplings with two H nuclei, believed to be the proton of the OH group attached directly to the unsaturated asymmetric carbon atom and the proton attached directly to the: other asymmetric carbon atom of the molecule were observed. The principal g-values were found to be 2.0030, 2.0017, 2.0027. The principal elements of the nuclear coupling are 7.45, 6.59, 4.28 and 8.56, 7.22, 18.71 G, respectively. The radical was found to be very stable. (C) 2000 Elsevier Science Ltd. All rights reserved.

Modified linear prediction method for directions of arrival estimation of narrow-band plane waves

A modified linear prediction (MLP) method is proposed in which the reference sensor is optimally located on the extended line of the array. The criterion of optimality is the minimization of the prediction error power, where the prediction error is defined as the difference between the reference sensor and the weighted array outputs. It is shown that the L2-norm of the least-squares array weights attains a minimum value for the optimum spacing of the reference sensor, subject to some soft constraint on signal-to-noise ratio (SNR). How this minimum norm property can be used for finding the optimum spacing of the reference sensor is described. The performance of the MLP method is studied and compared with that of the linear prediction (LP) method using resolution, detection bias, and variance as the performance measures. The study reveals that the MLP method performs much better than the LP technique.

Characterization of barium titanate fine powders formed from hydrothermal crystallization

A detailed evaluation of size, shape and microstrains of BaTiO3 crystallites produced by hydrothermal crystallization at 90 – 180 °C and 0.1 – 1.2 MPa, from amorphous TiO2· xH2O (3 < × < 8) gel and aqueous Ba(OH)2 is presented, using X-ray line-broadening and TEM studies. Whereas the concentration of Ba(OH)2 and the acceptor impurities affect the crystallite shape, the stoichimetry with respect to Ba/Ti, donor as well as acceptor impurities, and the temperature of crystallization influence the microstrains. It is shown that strains in the crystallites are related to the point defects in the lattice. Compensation of the residually present hydroxyl ions in the oxygen sublattice by cation vacancies results in strains leading to metastable presence of the cubic phase at room temperature. Studies on the diffuse phase transition behaviour of these submicron powders show that the stable tetragonal phase is produced only on annealing at high temperatures where the mobility of cations vacancies are larger. Heat-treatment reduces anisotropy and strain in undoped samples, whereas annealing is less effective in doped materials. Comparison of the crystillite size by TEM showed better agreement with the Warren—Averbach method.

Adsorption behaviour of an oxidised starch onto haematite in the presence of calcium

The adsorption behaviour of an oxidised starch AP as well as that of calcium onto haematite have been studied both individually and together. While the adsorption density of starch AP onto haematite is enhanced in the presence of calcium, the adsorption of calcium onto haematite is not promoted by starch AP. Flocculation tests on haematite ore fines in the presence of starch AP and calcium chloride reveal that the sequence in which calcium and starch are added governs the settling rates and turbidity values. Zeta potential, viscosity and conductivity measurements, and calcium ion binding studies with starch AP indicate calcium-starch interactions. Possible mechanisms involved in such interactions with respect to haematite flocculation have been discussed.

Aggregation of calcium ionophore (A23187) in phospholipid vesicles

The circular dichroism studies on calcium ionophore, A23187, incorporated in Dipalmitoyl phosphatidyl choline (DPPC) vesicle showed interesting time dependent changes in the CD spectra. Analysis of the data indicated the possible aggregation of the observed dimeric structure of this molecule in non-polar solvents into a stacked dimeric pore in the phospholipid vesicle.

Adsorption of oxygen and reactivity with HCl on a barium-doped lead surface

X.p.s. studies on the adsorption of oxygen on a barium-covered Pb surface have shown the presence of two distinct types of oxygen species: oxidic, O2–, and the peroxo-like O2–2(ads), and the surface has been identified as a composite of PbO and BaPbO3. On a barium pre-covered surface, the sticking probability of oxygen on Pb is increased. The O2–(ads) species preferentially reacts with HCl forming PbCl2(ads)via proton abstraction, whereas O2–2(ads) is not reactive with HCl vapour. On the Pb surface, the PbCl2 overlayer reacts with excess HCl, forming a volatile compound believed to be Pb(ClHCl)2, while in the presence of coadsorbed barium, the stability of PbCl2 is increased and the activation energy for the reaction: PbCl2(ads)+ 2HCl(g) Pb(ClHCl)2(g) is increased. Stronger intermetallic interaction is suggested to be the reason for higher PbCl2 stability.

An improved representation of vehicle incompatibility in frontal NCAP tests using a modified rigid barrier

With the objective of better understanding the significance of New Car Assessment Program (NCAP) tests conducted by the National Highway Traffic Safety Administration (NHTSA), head-on collisions between two identical cars of different sizes and between cars and a pickup truck are studied in the present paper using LS-DYNA models. Available finite element models of a compact car (Dodge Neon), midsize car (Dodge Intrepid), and pickup truck (Chevrolet C1500) are first improved and validated by comparing theanalysis-based vehicle deceleration pulses against corresponding NCAP crash test histories reported by NHTSA. In confirmation of prevalent perception, simulation-bascd results indicate that an NCAP test against a rigid barrier is a good representation of a collision between two similar cars approaching each other at a speed of 56.3 kmph (35 mph) both in terms of peak deceleration and intrusions. However, analyses carried out for collisions between two incompatible vehicles, such as an Intrepid or Neon against a C1500, point to the inability of the NCAP tests in representing the substantially higher intrusions in the front upper regions experienced by the cars, although peak decelerations in cars arc comparable to those observed in NCAP tests. In an attempt to improve the capability of a front NCAP test to better represent real-world crashes between incompatible vehicles, i.e., ones with contrasting ride height and lower body stiffness, two modified rigid barriers are studied. One of these barriers, which is of stepped geometry with a curved front face, leads to significantly improved correlation of intrusions in the upper regions of cars with respect to those yielded in the simulation of collisions between incompatible vehicles, together with the yielding of similar vehicle peak decelerations obtained in NCAP tests.

A low-cost lead-acid battery with high specific-energy

Lightweight grids for lead-acid battery grids have been prepared from acrylonitrile. butadiene styrene (ABS) copolymer followed by coating with lead. Subsequently, the grids have been electrochemically coated with a conductive and corrosion-resistant layer of polyaniline. These grids are about 75% lighter than those employed in conventional lead-acid batteries. Commercial-grade 6V/3.5 Ah (C-20-rate) lead-acid batteries have been assembled and characterized employing positive and negative plates constituting these grids. The specific energy of such a lead-acid battery is about 50 Wh/kg. The batteries can withstand fast charge-discharge duty cycles.