Mesoporous MnO2 synthesized by using a tri-block copolymer for electrochemical supercapacitor studies

Mesoporous MnO2 is prepared from KMnO4 by using a tri-block copolymer, namely, poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) (PEG-PPG-PEG) as a reducing as well as a structure-directing agent. The as synthesized MnO2 samples are poorly crystalline with mesoporosity having pore diameter between 8 and 40 nm. BET surface area as high as 273 m(2) g(-1) is obtained. By heating, the poorly crystalline MnO2 turns into a well crystalline form at 400 degrees C with nanorod morphology. However, the surface area decreases for the heated samples. Samples of MnO2 prepared by varying the ratio of KMnO4 and the copolymer, and also the heated samples are subjected to electrochemical characterization for supercapacitor studies. High specific capacitance values on mass basis are obtained for the as prepared mesoporous MnO2 samples. (C) 2011 Elsevier Inc. All rights reserved.

Flexible poly(vinyl alcohol-co-ethylene)/modified MMT moisture barrier composite for encapsulating organic devices

Flexible, nano-composite moisture barrier films of poly(vinyl alcohol-co-ethylene) with surface modified montmorillonite fabricated by solution casting were used to encapsulate organic devices. The composite films were characterized by FTIR, UV-visible spectroscopy and SEM imaging. Thermal and mechanical properties of the composite films were studied by DSC and UTM. Calcium degradation test was used to determine the transmission rate of water vapour through the composite films, which showed a gradual reduction from similar to 0.1 g m(-2) day(-1) to 0.0001 g m(-2) day(-1) with increasing modified montmorillonite loading in the neat copolymer. The increase in moisture barrier performance is attributed to the decreased water vapour diffusivity due to matrix-filler interactions in the composite. The accelerated aging test was carried out for non-encapsulated and encapsulated devices to evaluate the efficiency of the encapsulants. The encapsulated devices exhibited longer lifetimes indicating the efficacy of the encapsulant.

Studies on aluminum-isopropoxide doped poly(ethylene oxide), poly(vinyl alcohol), and poly(ethylene oxide)-poly(vinyl alcohol) blends

Poly( ethylene oxide), poly(vinyl alcohol): and their blend in a 40 : 60 mole ratio were doped with aluminum isopropoxide. Their structural, thermal, and electrical properties were studied. Aluminum isopropoxide acts as a Lewis acid and thus significantly influences the electrical properties of the polymers and the blend. It also acts as a scavanger for the trace quantities of water p-resent in them, thereby reducing the magnitude of proton transport. It also affects the structure of polymers that manifests in the thermal transformation and decomposition characteristics.

Gel-coated ion-exchange resin: A new kinetic model

Regenerable 'gel-coated' cationic resins with fast sorption kinetics and high sorption capacity have application potential for removal of trace metal ions even in large-scale operations. Poly(acrylic acid) has been gel-coated on high-surface area silica (pre-coated with ethylene-vinyl acetate copolymer providing a thin barrier layer) and insolubilized by crosslinking with a low-molecular-weight diepoxide (epoxy equivalent 180 g) in the presence of benzyl dimethylamine catalyst at 70 degrees C, In experiments performed for Ca2+ sorption from dilute aqueous solutions of Ca(NO,),, the gel-coated acrylic resin is found to have nearly 40% higher sorption capacity than the bead-form commercial methacrylic resin Amberlite IRC-50 and also several limes higher rate of sorption. The sorption on the gel-coated sorbent under vigorous agitation has the characteristics of particle diffusion control with homogeneous (gel) diffusion in resin phase. A new mathematical model is proposed for such sorption on gel-coated ion-exchange resin in finite bath and solved by applying operator-theoretic methods. The analytical solution so obtained shows goad agreement with experimental sorption kinetics at relatively low levels (< 70%) of resin conversion.

A polarized, twisted, ethylene: structure of methyl 2-(1,3-dimethyl-2-imidazolidinylidene)-3-oxobutyrate dihydrate, C10H16N2O3.2H2O

Mr = 248, monoclinic, P21/n, a = 12.028 (2), b=7.168(2), c= 15.187(5)A, fl=91.88(2) °, Z= 4, V= 1308.6,~3, Din= 1.26, Dx= 1.263 Mgm -3, 2 (Cu Ka) = 1.5418 .A, g = 0.86 mm -1, F(000) = 536, T= 293 K. Final R = 5.6% for 2120 observed reflexions. Owing to the push-pull effect, the C=C bond distance is as long as 1.464 (2)/k with the twist angle about the bond 62.6.

Volumetric behavior of ethylene and ethylene-hydrogen mixtures

A Burnett apparatus deslgned and fabrlcated was used to collect volumetric data for ethylene and ethylene-hydrogen mixtures. Measurements were made In the temperature range 298.15-423.15 K at Intervals of 25 K and In the pressure range 0.3-7.0 MPa. Vlrlal coefflclents derlved from the compresslblllty data are tabulated. The data are fltted to different equations of state.

Crystal Structure, Ultraviolet Spectrum, and Electronic Structure of a Strongly Twisted Push-Pull Ethylene, approaching an Amidinium-Vinylogous Dithioate Zwitterion

The crystal structure of 1,3-di benzyl -2 - (4,4-dimet hyl- 2,5- bist hioxocyclo hexylidene) imidazolidine (2) shows a twist of 80.8(5)' about the inter-ring bond, which has a length of 1.482(6) A. The near orthogonality of the donor and acceptor parts of this formal push-pull ethylene makes the structure approach that of a zwitterion, as evidenced by bond lengths indicating strong electron delocalization. The acceptor part approaches a vinylogous dithioate structure, the donor part an amidinium system. The U.V. spectrum shows an n + R and a R + R transition, at 51 1 and 41 7.5 nm, respectively; according to CNDO/S calculations these are located entirely in the [S-C-C-C-SI- part. Two bands at shorter wavelength are ascribed to transitions from combinations of the lone-pair orbitals on the sulphur atoms to a n* orbital in the [N-C-N] + part; this is facilitated by the near perpendicularity of the two parts of the molecule.

Intermolecular potentials in the dimer, the excimers, and the dimer ions of ethylene

Calculations are reported on the interaction energies in the dimer, the excimers, and the dimer ions of ethylene. The various a- and u-electron terms for different conformations of the dimeric species are determined by using the exchange perturbation method. The results predict that the singlet excimer and the dimer cation are stable primarily because of the large magnitude of the exciton-resonance and charge-resonance terms, respectively, while the neutral dimer, the triplet excimer, and the dimer anion are weakly stable. The variations of the various energy terms with conformations suggest that these dimeric species cannot have identifical structure.

Dilute solution properties of methyl methacrylate�acrylonitrile copolymer (MA1)

This paper deals with studies on the dilute solution properties of methyl methacrylate�acrylonitrile copolymer of 0.289 mole fraction (mf) of acrylonitrile composition. Mark�Houwink parameters for this copolymer have been evaluated in acetonitrile (MeCN), 2-butanone (MEK), dimethylformamide (DMF) and γ-butyrolactone (γ-BL). The solvent power is found to be in the order of MEK < MeCN < DMF < γ-BL at 30°C. Herein, probably for the first time, the steric factor for the copolymer is found to be lower than that for the parent homopolymers and the excess interaction parameter, �AB is found to be negative. This probably suggests that the units are compatible to each other.

Temperature influence on the excess interaction parameter of styrene-methyl methacrylate copolymer

Intrinsic viscosity data for polystyrene, poly(methyl methacrylate) and styrene-methyl methacrylate copolymer of azeotropic composition have been used to evaluate the excess interaction parameters at different temperatures in γ-butyrolactone and dimethylformamide. It is found that these values are positive and show a negligible increase with increase in temperature, indicating therefore that the hetero-contact interactions are not influenced by temperature, contrary to the results obtained by Dondos and Benoit for the same copolymer system in p-xylene and iso-amyl acetate.

Synthesis and structural characterization of a new ruthenium hydride ethylene complex

A ruthenium(II) ethylene complex, trans-[Ru(H)(C2H4)- (dppm)(2)][BF4], hearing two 1,1-bis(diphenylphosphino) methane (dppm) ligands has been synthesized and structurally characterized using X-ray crystallography. In the molecular structure, the Ru-II center shows a distorted octahedral coordination geometry formed by four P atoms of the two chelating dppm ligands, a hydride, and an ethylene ligands. The four dppm P atoms are almost co-planar with the hydride and the ethylene ligands perpendicular to this plane. The C-C bond distance of the bound ethylene is 1.375(6) angstrom, which is elongated by 0.042 angstrom as compared to free ethylene (1.333(2) angstrom). The packing diagram of the complex shows two voids or channels, which are occupied by BF4- counterion and water molecules.