Oil Retention and Pressure Drop in Horizontal and Vertical Suction Lines with R410A / POE ISO 32

In refrigeration systems a small amount of compressor lubricant is entrained in the refrigerant and circulated through the system, where some is retained in each component. The suction line to the compressor has the largest potential for oil retention. This paper presents results from an experimental apparatus that has been constructed to circulate POE (polyolester) oil and R410A at a controlled mass flux, OCR (oil in circulation ratio), and apparent superheat, and to directly measure the pressure drop and mass of oil retained in horizontal and vertical suction lines. The bulk vapor velocity and overall void fraction are determined from direct mass and temperature measurements. The oil retention, pressure drop, and flow regimes near the minimum ASHRAE recommended mass flux condition are explored. It was found that oil retention begins to increase sharply even above the minimum recommended flux, so conditions near the minimum should be avoided. Two relationships were developed to predict the oil retention in the vertical and horizontal suction lines. The average error from the predictions method was 10.9% for the vertical tube, and 7.9% for the horizontal tube.

A decrease in dkk1, a Wnt inhibitor, contributes to placental and fetal lipid accumulation in an obesity-prone rat model

Placenta, as the sole transport mechanism between mother and fetus, links the maternal physical state and the immediate and life-long outcomes of the offspring. The present study examined the mechanisms behind the effect of maternal obesity on placental lipid accumulation and metabolism. Pregnant Obese Prone (OP) and Obese Resistant (OR) rat strains were fed a control diet throughout gestation. Placentas were collected on gestational d21 for analysis and frozen placental sections were analyzed for fat accumulation as well as β-Catenin and Dkk1 localization. Additionally, DKK1 was overexpressed in JEG3 trophoblast cells, followed by treatment with NEFA and Oil Red O stain quantification and mRNA analysis to determine the relationship between placental DKK1 and lipid accumulation. Maternal plasma and placental NEFA and TG were elevated in OP dams, and offspring of OP dams were smaller than OR. Placental Dkk1 mRNA content was 4-fold lower in OP placentas, and there was a significant increase in β-Catenin accumulation as well as mRNA content of fat transport and TG synthesis enzymes, including Ppar-delta, Fatp1, Fat/Cd36, Lipin1, and Lipin3. There was significant lipid accumulation within the decidual zones in OP but not OR placentas, and the thickness of the decidual and junctional zones was significantly smaller in OP than OR placentas. Overexpression of DKK1 in JEG3 cells decreased lipid accumulation and the mRNA content of PPAR-Delta, FATP1, FAT/CD36, LIPIN1, and LIPIN3. Our results indicate that Dkk1 may be regulating placental lipid metabolism through Wnt-mediated mechanisms. Additionally, recent studies have suggested that maternal obesity may also program early development of non-alcoholic fatty liver disease (NAFLD), rates of which have correlated with the increase in the obesity epidemic. In the current study, livers of OP offspring had significantly increased TG content (P<0.05) and lipid accumulation when compared to offspring of OR dams. Additionally, hepatic Dkk1 mRNA content was significantly decreased in OP livers when compared to OR (P<0.05), and treating H4IIECR rat hepatocyte cells with NEFA showed that Dkk1 mRNA was also decreased in NEFA-treated cells (P<0.05) that also had lipid accumulation. Chromatin Immunoprecipitation (ChIP) analysis of the Dkk1 promoter in fetal livers showed a pattern of histone modifications associated with decreased gene transcription in OP offspring, which agrees with our gene expression data. These results demonstrate that the hepatic Dkk1 gene is epigenetically regulated via histone modification in neonatal offspring in the current model of gestational obesity, and future studies will be needed to determine whether these changes contribute to excessive hepatic lipid accumulation in offspring of obese dams.

A geometric study of liquid retention in open-cell metal foams

Open-cell metal foams show promise as an emerging novel material for heat exchanger applications. The high surface-area-to-volume ratio suggests increased compactness and decrease in weight of heat exchanger designs. However, the metal foam structure appears conducive to condensate retention, which would degenerate heat transfer performance. This research investigates the condensate retention behavior of aluminum open-cell metal foams through the use of static dip tests and geometrical classification via X-ray Micro-Computed Tomography. Aluminum open-cell metal foam samples of 5, 10, 20, and 40 pores per inch (PPI), all having a void fraction greater than 90%, were included in this investigation. In order to model the condensate retention behavior of metal foams, a clearer understanding of the geometry was required. After exploring the ideal geometries presented in the open literature, X-ray Micro-Computed Tomography was employed to classify the actual geometry of the metal foam samples. The images obtained were analyzed using specialized software from which geometric information including strut length and pore shapes were extracted. The results discerned a high variability in ligament length, as well as features supporting the ideal geometry known as the Weaire-Phelan unit cell. The static dip tests consisted of submerging the metal foam samples in a liquid, then allowing gravity-induced drainage until steady-state was reached and the liquid remaining in the metal foam sample was measured. Three different liquids, water, ethylene glycol, and 91% isopropyl alcohol, were employed. The behaviors of untreated samples were compared to samples subjected to a Beomite surface treatment process, and no significant differences in retention behavior were discovered. The dip test results revealed two distinct regions of condensate retention, each holding approximately half of the total liquid retained by the sample. As expected, condensate retention increased as the pores sizes decreased. A model based on surface tension was developed to predict the condensate retention in the metal foam samples and verified using a regular mesh. Applying the model to both the ideal and actual metal foam geometries showed good agreement with the dip test results in this study.