The bioaccumulation of persistent contaminants by zebra mussels and their effects on state-endangered common terns

Common terns currently are listed as endangered or threatened in many states, including Illinois, Vermont, Pennsylvania, Ohio, Wisconsin, Michigan, and New York, and a species of special concern by the U.S. Fish and Wildlife Service (USFWS, 2002). The sole remaining nesting colony in Illinois is located at the Naval Station Great Lakes (NSGL) in Lake County where intensive management by the Illinois Department of Natural Resources has reduced nest predation and increased the number of eggs that hatch. However, the overall reproductive success (the number of young successfully reaching independence) has not improved. Observations of gross deformities in hatchlings (i.e. compromised feather development and cross-bill), lethargic behavior of young birds, and lesions, suggested the influence of environmental contaminants (Jablonski et al., 2005). I investigated if there were significant levels of environmental contaminants in eggs and nestlings of common terns. While there were minimal concentration of selenium, mercury, lead, and cadmium, there were large concentration of polychlorinated biphenyls (PCBs) in both the eggs and nestlings. The greater amounts of PCBs in older chicks than younger chicks suggest local contamination. In order to potentially manage the factors responsible for exposing the terns to PCBs I investigated the pathway by which PCBs were exposed to terns. The two most likely biological pathways as determined by research on Great Lake fishes were investigated. The first pathway is through atmospheric deposition of PCBs and resuspension of PCB-ladel sediment which are subsequently acquired by filter-feeding fish (e.g. alewives, Alosa pseudoharengus) and then pelagic fish (e.g. lake trout, Salvelinus namaychus) or in this case terns. The second pathway explored was via the biodeposits of zebra mussels which are consumed by round gobies (Neogobius melanostromus) and ultimately littoral fish (e.g. small-mouthed bass, Micropterus dolomieui) or terns. Because common terns breed in near-shore sites where concentrations of zebra mussels are found, as well as forage in more pelagic environments it is possible that either or both pathways may be contributing to their PCB exposure. Field experiments and stable isotope analyses demonstrated that the most likely pathway by which terns are exposed to PCBs is via alewives, similar to how apex predators such as lake trout acquire PCBs. Biodeposits from zebra mussels do not appear to be a significant factor in PCB accumulation in terns. The impact of PCB exposure on birds can vary widely, however in this situation we choise to investigate one specific behavior often affected by PCB exposure, parental attentiveness. PCBs are known to cause endocrine disruption which ultimately results in reduced brooding of young and incubation of eggs. I used temperature sensors to quantify nest temperatures and parental attentiveness during incubation. High concentrations of PCBs in our study population appear to be leading to poor parental attentiveness, and extended periods of absence during incubation and brooding, ultimately leading to poor reproductive success. Common terns are perilously close to being extirpated in Illinois and management of PCB exposure will be difficult. I propose that additional testing should be conducted to locate a site with less PCB contamination and then to move the tern colony to this location, possibly using social cues as has been done with other tern species in Illinois. PCBs are having a profound impact on common tern populations in Illinois and without moving the colony it is likely that the population will continue to decline.

Fiber Bragg Gratings Strain Sensors for Railway Applications

Fiber optical sensors have played an important role in applications for monitoring the health of civil infrastructures, such as bridges, oil rigs, and railroads. Due to the reduction in cost of fiber-optic components and systems, fiber optical sensors have been studied extensively for their higher sensitivity, precision and immunity to electrical interference compared to their electrical counterparts. A fiber Bragg grating (FBG) strain sensor has been employed for this study to detect and distinguish normal and lateral loads on rail tracks. A theoretical analysis of the relationship between strain and displacement under vertical and horizontal strains on an aluminum beam has been performed, and the results are in excellent agreement with the measured strain data. Then a single FBG sensor system with erbium-doped fiber amplifier broadband source has been carried out. Force and temperature applied on the system have resulted in changes of 0.05 nm per 50 με and 0.094 nm per 10 oC at the center wavelength of the FBG. Furthermore, a low cost fiber-optic sensor system with a distributed feedback (DFB) laser as the light source has been implemented. We show that it has superior noise and sensitivity performances compared to strain gauge sensors. The design has been extended to accommodate multiple sensors with negligible cross talk. When two cascaded sensors on a rail track section are tested, strain readings of the sensor 20 inches away from the position of applied force decay to one seventh of the data of the sensor at the applied force location. The two FBG sensor systems can detect 1 ton of vertical load with a square wave pattern and 0.1 ton of lateral loads (3 tons and 0.5 ton, respectively, for strain gauges). Moreover, a single FBG sensor has been found capable of detecting and distinguishing lateral and normal strains applied at different frequencies. FBG sensors are promising alternatives to electrical sensors for their high sensitivity,ease of installation, and immunity to electromagnetic interferences.

Microcantilever sensors for biochemical detection and analysis

Biochemical agents, including bacteria and toxins, are potentially dangerous and responsible for a wide variety of diseases. Reliable detection and characterization of small samples is necessary in order to reduce and eliminate their harmful consequences. Microcantilever sensors offer a potential alternative to the state of the art due to their small size, fast response time, and the ability to operate in air and liquid environments. At present, there are several technology limitations that inhibit application of microcantilever to biochemical detection and analysis, including difficulties in conducting temperature-sensitive experiments, material inadequacy resulting in insufficient cell capture, and poor selectivity of multiple analytes. This work aims to address several of these issues by introducing microcantilevers having integrated thermal functionality and by introducing nanocrystalline diamond as new material for microcantilevers. Microcantilevers are designed, fabricated, characterized, and used for capture and detection of cells and bacteria. The first microcantilever type described in this work is a silicon cantilever having highly uniform in-plane temperature distribution. The goal is to have 100 μm square uniformly heated area that can be used for thermal characterization of films as well as to conduct chemical reactions with small amounts of material. Fabricated cantilevers can reach above 300C while maintaining temperature uniformity of 2−4%. This is an improvement of over one order of magnitude over currently available cantilevers. The second microcantilever type is a doped single crystal silicon cantilever having a thin coating of ultrananocrystalline diamond (UNCD). The primary application of such a device is in biological testing, where diamond acts as a stable, electrically isolated reaction surface while silicon layer provides controlled heating with minimum variations in temperature. This work shows that composite cantilevers of this kind are an effective platform for temperature-sensitive biological experiments, such as heat lysing and polymerase chain reaction. The rapid heat-transfer of Si-UNCD cantilever compromised the membrane of NIH 3T3 fibroblast and lysed the cell nucleus within 30 seconds. Bacteria cells, Listeria monocytogenes V7, were shown to be captured with biotinylated heat-shock protein on UNCD surface and 90% of all viable cells exhibit membrane porosity due to high heat in 15 seconds. Lastly, a sensor made solely from UNCD diamond is fabricated with the intention of being used to detect the presence of biological species by means of an integrated piezoresistor or through frequency change monitoring. Since UNCD diamond has not been previously used in piezoresistive applications, temperature-denpendent piezoresistive coefficients and gage factors are determined first. The doped UNCD exhibits a significant piezoresistive effect with gauge factor of 7.53±0.32 and a piezoresistive coefficient of 8.12×10^−12 Pa^−1 at room temperature. The piezoresistive properties of UNCD are constant over the temperature range of 25−200C. 300 μm long cantilevers have the highest sensitivity of 0.186 m-Ohm/Ohm per μm of cantilever end deflection, which is approximately half that of similarly sized silicon cantilevers. UNCD cantilever arrays were fabricated consisting of four sixteen-cantilever arrays of length 20–90 μm in addition to an eight-cantilever array of length 120 μm. Laser doppler vibrometry (LDV) measured the cantilever resonant frequency, which ranged as 218 kHz−5.14 MHz in air and 73 kHz−3.68 MHz in water. The quality factor of the cantilever was 47−151 in air and 18−45 in water. The ability to measure frequencies of the cantilever arrays opens the possibility for detection of individual bacteria by monitoring frequency shift after cell capture.