Integrated micro fuel cells with on-board hydride reactors and autonomous control schemes

Miniaturization of power generators to the MEMS scale, based on the hydrogen-air fuel cell, is the object of this research. The micro fuel cell approach has been adopted for advantages of both high power and energy densities. On-board hydrogen production/storage and an efficient control scheme that facilitates integration with a fuel cell membrane electrode assembly (MEA) are key elements for micro energy conversion. Millimeter-scale reactors (ca. 10 µL) have been developed, for hydrogen production through hydrolysis of CaH2 and LiAlH4, to yield volumetric energy densities of the order of 200 Whr/L. Passive microfluidic control schemes have been implemented in order to facilitate delivery, self-regulation, and at the same time eliminate bulky auxiliaries that run on parasitic power. One technique uses surface tension to pump water in a microchannel for hydrolysis and is self-regulated, based on load, by back pressure from accumulated hydrogen acting on a gas-liquid microvalve. This control scheme improves uniformity of power delivery during long periods of lower power demand, with fast switching to mass transport regime on the order of seconds, thus providing peak power density of up to 391.85 W/L. Another method takes advantage of water recovery by backward transport through the MEA, of water vapor that is generated at the cathode half-cell reaction. This regulation-free scheme increases available reactor volume to yield energy density of 313 Whr/L, and provides peak power density of 104 W/L. Prototype devices have been tested for a range of duty periods from 2-24 hours, with multiple switching of power demand in order to establish operation across multiple regimes. Issues identified as critical to the realization of the integrated power MEMS include effects of water transport and byproduct hydrate swelling on hydrogen production in the micro reactor, and ambient relative humidity on fuel cell performance.

Material characterization and process development for indium-arsenide / indium-gallium-antimonide channel, high electron mobility transistors for low power, high speed applications

Efforts to push the performance of transistors for millimeter-wave and microwave applications have borne fruit through device size scaling and the use of novel material systems. III-V semiconductors and their alloys hold a distinct advantage over silicon because they have much higher electron mobility which is a prerequisite for high frequency operation. InGaAs/InP pseudomorphic heterojunction bipolar transistors (HBTs) have demonstrated fT of 765 GHz at room temperature and InP based high electron mobility transistors (HEMTs) have demonstrated fMax of 1.2 THz. The 6.1 A lattice family of InAs, GaSb, AlSb covers a wide variety of band gaps and is an attractive future material system for high speed device development. Extremely high electron mobilities ~ 30,000 cm^2 V^-1s^-1 have been achieved in modulation doped InAs-AlSb structures. The work described in this thesis involves material characterization and process development for HEMT fabrication on this material system.

Low-power high-performance SAR ADC design with digital calibration techniques

This dissertation presents the design of three high-performance successive-approximation-register (SAR) analog-to-digital converters (ADCs) using distinct digital background calibration techniques under the framework of a generalized code-domain linear equalizer. These digital calibration techniques effectively and efficiently remove the static mismatch errors in the analog-to-digital (A/D) conversion. They enable aggressive scaling of the capacitive digital-to-analog converter (DAC), which also serves as sampling capacitor, to the kT/C limit. As a result, outstanding conversion linearity, high signal-to-noise ratio (SNR), high conversion speed, robustness, superb energy efficiency, and minimal chip-area are accomplished simultaneously. The first design is a 12-bit 22.5/45-MS/s SAR ADC in 0.13-μm CMOS process. It employs a perturbation-based calibration based on the superposition property of linear systems to digitally correct the capacitor mismatch error in the weighted DAC. With 3.0-mW power dissipation at a 1.2-V power supply and a 22.5-MS/s sample rate, it achieves a 71.1-dB signal-to-noise-plus-distortion ratio (SNDR), and a 94.6-dB spurious free dynamic range (SFDR). At Nyquist frequency, the conversion figure of merit (FoM) is 50.8 fJ/conversion step, the best FoM up to date (2010) for 12-bit ADCs. The SAR ADC core occupies 0.06 mm2, while the estimated area the calibration circuits is 0.03 mm2. The second proposed digital calibration technique is a bit-wise-correlation-based digital calibration. It utilizes the statistical independence of an injected pseudo-random signal and the input signal to correct the DAC mismatch in SAR ADCs. This idea is experimentally verified in a 12-bit 37-MS/s SAR ADC fabricated in 65-nm CMOS implemented by Pingli Huang. This prototype chip achieves a 70.23-dB peak SNDR and an 81.02-dB peak SFDR, while occupying 0.12-mm2 silicon area and dissipating 9.14 mW from a 1.2-V supply with the synthesized digital calibration circuits included. The third work is an 8-bit, 600-MS/s, 10-way time-interleaved SAR ADC array fabricated in 0.13-μm CMOS process. This work employs an adaptive digital equalization approach to calibrate both intra-channel nonlinearities and inter-channel mismatch errors. The prototype chip achieves 47.4-dB SNDR, 63.6-dB SFDR, less than 0.30-LSB differential nonlinearity (DNL), and less than 0.23-LSB integral nonlinearity (INL). The ADC array occupies an active area of 1.35 mm2 and dissipates 30.3 mW, including synthesized digital calibration circuits and an on-chip dual-loop delay-locked loop (DLL) for clock generation and synchronization.

An examination of factors that influence entrepreneurial intention of high school students in Kenya

Abstract Considerable research has been carried out on entrepreneurship in efforts to understand its incidence in order to influence and maximize its benefits. Essentially, researchers and policy makers have sought to understand the link between individuals and business creation: Why some people start businesses while others do not. The research indicates that personality traits, individual background factors and association of entrepreneurship with career choice and small business enterprises, cannot sufficiently explain entrepreneurship. It is recognized that entrepreneurship is an intentional process and based on Ajzen’s Theory of Planned Behavior, the most defining characteristic of entrepreneurship is the intention to start a business. The purpose of this study was, therefore, to examine factors that influence entrepreneurial intention in high school students in Kenya. Specifically, the study aimed at determining if there were relationships between the perceptions of desirability, and feasibility of entrepreneurship with entrepreneurial intention of the students, identifying any difference in these perceptions with students of different backgrounds, and developing a model to predict entrepreneurship in the students. The study, therefore, tested how well Ajzen’s Theory of Planned Behavior applied in the Kenyan situation. A questionnaire was developed and administered to 969 final year high school students at a critical important point in their career decision making. Participants were selected using a combined convenience and random sampling technique, considering gender, rural/urban location, cost, and accessibility. Survey was the major method of data collection. Data analysis methods included descriptive statistics, correlation, ANOVA, factor analysis, effect size, and regression analysis. iii The findings of this study corroborate results from past studies. Attitudes are found to influence intention, and the attitudes to be moderated by individual background factors. Perceived personal desirability of entrepreneurship was found to have the greatest influence on entrepreneurial intention and perceived feasibility the lowest. The study findings also showed that perceived social desirability and feasibility of entrepreneurship contributed to perception of personal desirability, and that the background factors, including gender and prior experience, influenced entrepreneurial intention both directly and indirectly. In addition, based on the literature reviewed, the study finds that entrepreneurship promotion requires reduction of the high small business mortality rate and creation of both entrepreneurs and entrepreneurial opportunities (Kruger, 2000; Shane & Venkataraman, 2000). These findings have theoretical and practical implications for researchers, policy makers, teachers, and other entrepreneurship practitioners in Kenya.