The structure of Norway spruce (Picea abies [L.] Karst.) stems in relation to wood properties of sawn timber

An important challenge in forest industry is to get the appropriate raw material out from the forests to the wood processing industry. Growth and stem reconstruction simulators are therefore increasingly integrated in industrial conversion simulators, for linking the properties of wooden products to the three-dimensional structure of stems and their growing conditions. Static simulators predict the wood properties from stem dimensions at the end of a growth simulation period, whereas in dynamic approaches, the structural components, e.g. branches, are incremented along with the growth processes. The dynamic approach can be applied to stem reconstruction by predicting the three-dimensional stem structure from external tree variables (i.e. age, height) as a result of growth to the current state. In this study, a dynamic growth simulator, PipeQual, and a stem reconstruction simulator, RetroSTEM, are adapted to Norway spruce (Picea abies [L.] Karst.) to predict the three-dimensional structure of stems (tapers, branchiness, wood basic density) over time such that both simulators can be integrated in a sawing simulator. The parameterisation of the PipeQual and RetroSTEM simulators for Norway spruce relied on the theoretically based description of tree structure developing in the growth process and following certain conservative structural regularities while allowing for plasticity in the crown development. The crown expressed both regularity and plasticity in its development, as the vertical foliage density peaked regularly at about 5 m from the stem apex, varying below that with tree age and dominance position (Study I). Conservative stem structure was characterized in terms of (1) the pipe ratios between foliage mass and branch and stem cross-sectional areas at crown base, (2) the allometric relationship between foliage mass and crown length, (3) mean branch length relative to crown length and (4) form coefficients in branches and stem (Study II). The pipe ratio between branch and stem cross-sectional area at crown base, and mean branch length relative to the crown length may differ in trees before and after canopy closure, but the variation should be further analysed in stands of different ages and densities with varying site fertilities and climates. The predictions of the PipeQual and RetroSTEM simulators were evaluated by comparing the simulated values to measured ones (Study III, IV). Both simulators predicted stem taper and branch diameter at the individual tree level with a small bias. RetroSTEM predictions of wood density were accurate. For focusing on even more accurate predictions of stem diameters and branchiness along the stem, both simulators should be further improved by revising the following aspects in the simulators: the relationship between foliage and stem sapwood area in the upper stem, the error source in branch sizes, the crown base development and the height growth models in RetroSTEM. In Study V, the RetroSTEM simulator was integrated in the InnoSIM sawing simulator, and according to the pilot simulations, this turned out to be an efficient tool for readily producing stand scale information about stem sizes and structure when approximating the available assortments of wood products.

What was behind the bark? : An assessment of decay among urban Tilia, Betula and Acer trees felled as hazardous in the Helsinki City area

Old trees growing in urban environments are often felled due to symptoms of mechanical defects that could be hazardous to people and property. The decisions concerning these removals are justified by risk assessments carried out by tree care professionals. The major motivation for this study was to determine the most common profiles of potential hazard characteristics for the three most common urban tree genera in Helsinki City: Tilia, Betula and Acer, and in this way improve management practices and protection of old amenity trees. For this research, material from approximately 250 urban trees was collected in cooperation with the City of Helsinki Public Works Department during 2001 - 2004. From the total number of trees sampled, approximately 70% were defined as hazardous. The tree species had characteristic features as potential hazard profiles. For Tilia trees, hollowed heartwood with low fungal activity and advanced decay caused by Ganoderma lipsiense were the two most common profiles. In Betula spp., the primary reason for tree removal was usually lowered amenity value in terms of decline of the crown. Internal cracks, most often due to weak fork formation, were common causes of potential failure in Acer spp. Decay caused by Rigidoporus populinus often increased the risk of stem breakage in these Acer trees. Of the decay fungi observed, G. lipsiense was most often the reason for the increased risk of stem collapse. Other fungi that also caused extensive decay were R. populinus, Inonotus obliquus, Kretzschmaria deusta and Phellinus igniarius. The most common decay fungi in terms of incidence were Pholiota spp., but decay caused by these species did not have a high potential for causing stem breakage, because it rarely extended to the cambium. The various evaluations used in the study suggested contradictions in felling decisions based on trees displaying different stages of decay. For protection of old urban trees, it is crucial to develop monitoring methods so that tree care professionals could better analyse the rate of decay progression towards the sapwood and separate those trees with decreasing amounts of sound wood from those with decay that is restricted to the heartwood area.

The effect of lignin content and lignin modification on Norway spruce wood properties and decay resistance

Three different Norway spruce cutting clones growing in three environments with different soil and climatic conditions were studied. The purpose was to follow variation in the radial growth rate, wood properties and lignin content and to modify wood lignin with a natural monolignol, coniferyl alcohol, by making use of inherent wood peroxidases. In addition, the incorporation of chlorinated anilines into lignin was studied with synthetic model compounds and synthetic lignin preparations to show whether unnatural compounds originating from pesticides could be bound in the lignin polymer. The lignin content of heartwood, sapwood and earlywood was determined by applying Fourier transform infrared (FTIR) spectroscopy and a principal component regression (PCR) technique. Wood blocks were treated with coniferyl alcohol by using a vacuum impregnation method. The effect of impregnation was assessed by FTIR and by a fungal decay test. Trees from a fertile site showed the highest growth rate and sapwood lignin content and the lowest latewood proportion, weight density and modulus of rupture (MOR). Trees from a medium fertile site had the lowest growth rate and the highest latewood proportion, weight density, modulus of elasticity (MOE) and MOR. The most rapidly growing clone showed the lowest latewood proportion, weight density, MOE and MOR. The slowest growing clone had the lowest sapwood lignin content and the highest latewood proportion, weight density, MOE and MOR. Differences between the sites and clones were small, while fairly large variation was found between the individual trees and growing seasons. The cutting clones maintained clone-dependent wood properties in the different growing sites although variation between trees was high and climatic factors affected growth. The coniferyl alcohol impregnation increased the content of different lignin-type phenolic compounds in the wood as well as wood decay resistance against a white-rot fungus, Coriolus versicolor. During the synthetic lignin preparation 3,4-dichloroaniline became bound by a benzylamine bond to β-O-4 structures in the polymer and it could not be released by mild acid hydrolysis. The natural monolignol, coniferyl alcohol, and chlorinated anilines could be incorporated into the lignin polymer in vivo and in vitro, respectively.