Role of heat treatment in the processing and quality of oat flakes

This thesis reports on investigations into the influence of heat treatment on the manufacturing of oat flakes. Sources of variation in the oat flake quality are reviewed, including the whole chain from the farm to the consumer. The most important quality parameters of oat flakes are the absence of lipid hydrolysing enzymes, specific weight, thickness, breakage (fines), water absorption. Flavour, colour and pasting properties are also important, but were not included in the experimental part of this study. Of particular interest was the role of heat processing. The first possible heat treatment may occur already during grain drying, which in Finland generally happens at the farm. At the mill, oats are often kilned to stabilise the product by inactivating lipid hydrolysing enzymes. Almost invariably steaming is used during flaking, to soften the groats and reduce flake breakage. This thesis presents the use of a material science approach to investigating a complex system, typical of food processes. A combination of fundamental and empirical rheological measurements was used together with a laboratory scale process to simulate industrial processing. The results were verified by means of industrial trials. Industrially produced flakes at three thickness levels (nominally 0.75, 0.85 and 0.90 mm) were produced from kilned and unkilned oat groats, and the flake strength was measured at different moisture contents. Kilning was not found to significantly affect the force required to puncture a flake with a 2mm cylindrical probe, which was taken as a measure of flake strength. To further investigate how heat processing contributes to flake quality, dynamic mechanical analysis was used to characterise the effect of heat on the mechanical properties of oats. A marked stiffening of the groat, of up to about 50% increase in storage modulus, was observed during first heating at around 36 to 57°C. This was also observed in tablets prepared from ground groats and extracted oat starch. This stiffening was thus attributed to increased adhesion between starch granules. Groats were steamed in a laboratory steamer and were tempered in an oven at 80 110°C for 30 90 min. The maximum force required to compress the steamed groats to 50% strain increased from 50.7 N to 57.5 N as the tempering temperature was increased from 80 to 110°C. Tempering conditions also affected water absorption. A significantly higher moisture content was observed for kilned (18.9%) compared to unkilned (17.1%) groats, but otherwise had no effect on groat height, maximum force or final force after a 5 s relaxation time. Flakes were produced from the tempered groats using a laboratory flaking machine, using a roll gap of 0.4 mm. Apart from specific weight, flake properties were not influenced by kilning. Tempering conditions however had significant effects on the specific weight, thickness and water absorption of the flakes, as well as on the amount of fine material (<2 mm) produced during flaking. Flake strength correlated significantly with groat strength and flake thickness. Trial flaking at a commercial mill confirmed that groat temperature after tempering influenced water absorption. Variation in flake strength was observed , but at the groat temperatures required to inactivate lipase, it was rather small. Cold flaking of groats resulted in soft, floury flakes. The results presented in this thesis suggest that heating increased the adhesion between starch granules. This resulted in an increase in the stiffness and brittleness of the groat. Brittle fracture, rather than plastic flow, during flaking could result in flaws and cracks in the flake. These would be expected to increase water absorption. This was indeed observed as tempering temperature increased. Industrial trials, conducted with different groat temperatures, confirmed the main findings of the laboratory experiments. The approach used in the present study allowed the systematic study of the effect of interacting process parameters on product quality. There have been few scientific studies of oat processing, and these results can be used to understand the complex effects of process variables on flake quality. They also offer an insight into what happens as the oat groat is deformed into a flake.

Occupational chronic solvent encephalopathy in Finland 1995 - 2007 : incidence and diagnostic methods

The occurrence of occupational chronic solvent encephalopathy (CSE) seems to decrease, but still every year reveals new cases. To prevent CSE and early retirement of solvent-exposed workers, actions should focus on early CSE detection and diagnosis. Identifying the work tasks and solvent exposure associated with high risk for CSE is crucial. Clinical and exposure data of all the 128 cases diagnosed with CSE as an occupational disease in Finland during 1995-2007 was collected from the patient records at the Finnish Institute of Occupational Health (FIOH) in Helsinki. The data on the number of exposed workers in Finland were gathered from the Finnish Job-exposure Matrix (FINJEM) and the number of employed from the national workforce survey. We analyzed the work tasks and solvent exposure of CSE patients and the findings in brain magnetic resonance imaging (MRI), quantitative electroencephalography (QEEG), and event-related potentials (ERP). The annual number of new cases diminished from 18 to 3, and the incidence of CSE decreased from 8.6 to 1.2 / million employed per year. The highest incidence of CSE was in workers with their main exposure to aromatic hydrocarbons; during 1995-2006 the incidence decreased from 1.2 to 0.3 / 1 000 exposed workers per year. The work tasks with the highest incidence of CSE were floor layers and lacquerers, wooden surface finishers, and industrial, metal, or car painters. Among 71 CSE patients, brain MRI revealed atrophy or white matter hyperintensities or both in 38% of the cases. Atrophy which was associated with duration of exposure was most frequently located in the cerebellum and in the frontal or parietal brain areas. QEEG in a group of 47 patients revealed increased power of the theta band in the frontal brain area. In a group of 86 patients, the P300 amplitude of auditory ERP was decreased, but at individual level, all the amplitude values were classified as normal. In 11 CSE patients and 13 age-matched controls, ERP elicited by a multimodal paradigm including an auditory, a visual detection, and a recognition memory task under single and dual-task conditions corroborated the decrease of auditory P300 amplitude in CSE patients in single-task condition. In dual-task conditions, the auditory P300 component was, more often in patients than in controls, unrecognizable. Due to the paucity and non-specificity of the findings, brain MRI serves mainly for differential diagnostics in CSE. QEEG and auditory P300 are insensitive at individual level and not useful in the clinical diagnostics of CSE. A multimodal ERP paradigm may, however, provide a more sensitive method to diagnose slight cognitive disturbances such as CSE.

Cutaneous porphyrias : Clinical and histopathological study

The prevalence of variegate porphyria (VP) (2.1:100 000, in 2006 n=108) was higher in Finland than elsewhere in European countries due to a founder effect (R152C). The incidence of VP was estimated at 0.2:1 000 000 based on the number of new symptomatic patients yearly. The prevalence of porphyria cutanea tarda (PCT) was 1.2:100 000 (in 2006 n=63), which is only one fourth of the numbers reported from other European countries. The estimated incidence of PCT was 0.5:1 000 000. Based on measurements of the uroporphyrinogen decarboxylase activity in erythrocytes, the proportion of familial PCT was 49% of the cases. The prevalence of erythropoietic protoporphyria (EPP) was at 0.8:100 000 (in 2006 n=39) including asymptomatic carriers of a mutation in the ferrochelatase (FECH) gene. The incidence of EPP was estimated at 0.1:1 000 000. After 1980 the penetrance was 37% among patients with VP. Of the mutation carriers (n=57) 30% manifested with skin symptoms. Frequency of skin symptom as only clinical sign was stable before or after 1980 (22% vs. 21%), but acute attacks became infrequent (29% vs. 7%). Of the symptomatic patients 30% had both acute attacks and skin symptoms and 80% had skin symptoms. Fragility (95%) and blistering (46%) of the skin in the backs of the hands were the most common skin symptoms. Transient correction of porphyrin metabolism using eight haem arginate infusions within five weeks had no effect on the skin symptoms in three of four patients with VP. In one case skin symptoms disappeared transiently. One patient with homozygous VP had severe photosensitivity since birth. Sensory polyneuropathy, glaucoma and renal failure developed during the 25-year follow-up without the presence of acute attacks. The I12T mutation was detected in both of his alleles in the protoporphyrinogen oxidase gene. Lack of skin symptoms and infrequency of acute attacks (1/9) in the patients with I12T mutation at the heterozygous stage indicate a mild phenotype (the penetrance 11%). Four mutations (751delGAGAA, 1122delT, C286T, C343T) in the FECH gene were characterised in four of 15 families with EPP. Burning pain (96%) and swelling (92%) of the sun-exposed skin were the major skin symptoms. Hepatopathy appeared in one of 25 symptomatic patients (4%). Clinical manifestations and associated factors of PCT were similar in the sporadic and familial types of PCT. The majority of the patients with PCT had one to three precipitating factors: alcohol intake (78%), mutations in hemochromatosis associated gene (50%), use of oestrogen (25% of women) and hepatitis B or C infections (25 %). Fatty liver disease (67%) and siderosis (67%) were commonly found in their liver biopsies. The major histopathological change of the sun-exposed skin in the patients with VP (n=20), EPP (n=8) and PCT (n=5) was thickening of the vessel walls of the upper dermis suggesting that the vessel wall is the primary site of the phototoxic reaction in each type of porphyria. The fine structure of the vessel walls was similar in VP, EPP and PCT consisting of the multilayered basement membrane and excess of finely granular substance between the layers which were surrounded by the band of homogenous material. EPP was characterised by amorphous perivascular deposits extending also to the extravascular space. In direct immunofluorescence study homogenous IgG deposits in the vessel walls of the upper dermis of the sun-exposed skin were demonstrated in each type of porphyria. In EPP the excess material around vessel walls consisted of other proteins such as serum amyloid protein, and kappa and lambda light chains in addition to the basement membrane constituents such as collagen IV and laminin. These results suggest that the alterations of the vessel walls are a consequence of the repeated damage and the repairing process in the vessel wall. The microscopic alterations could be demonstrated even in the normal looking but sun-exposed skin of the patients with EPP during the symptom-free phase suggesting that vascular change can be chronic. The stability of vascular changes in the patients with PCT after treatment indicates that circulating porphyrins are not important for the maintenance of the changes.

Parisuhde ja ero : Sosiologinen analyysi terapeuttisesta ymmärryksestä

This study takes as its premise the prominent social and cultural role that the couple relationship has acquired in modern society. Marriage as a social institution and romantic love as a cultural script have not lost their significance but during the last few decades the concept of relationship has taken prominence in our understanding of the love relationship. This change has taken place in a society governed by the therapeutic ethos. This study uses material ranging from in-depth interviews to various mass media texts to investigate the therapeutic logic that determines our understanding of the couple relationship. The central concept in this study is therapeutic relationship which does not refer to any particular type of relationship. In contemporary usage the relationship is, by definition, therapeutic. The therapeutic relationship is seen as an endless source of conflict and a highly complex dynamic unit in constant need of attention and treatment. Notwithstanding this emphasis on therapy and relationship work the therapeutic relationship lacks any morally or socially defined direction. Here lies the cultural power and according to critics the dubious aspect of the therapeutic ethos. For the therapeutic logic any reason for divorce is possible and plausible. Prosaically speaking the question is not whether to divorce or not, but when to divorce. In the end divorce only attests to the complexity of the relationship. The therapeutic understanding of the relationship gives the illusion that relationships with their tensions and conflicting emotions can be fully transferred to the sphere of transparency and therapeutic processing. This illusion created by relationship talk that emphasizes individual control is called omnipotence of the individual. However, the study shows that the individual omnipotence is inevitably limited and hence cracks appear in it. The cracks in the omnipotence show that while the therapeutic relationship based on the ideal of communication gives an individual a mode of speaking that stresses autonomy, equality and emotional gratification, it offers little help in expressing our fundamental dependence on other people. The study shows how strong an attraction the therapeutic ethos has with its grasp on the complexities of the relationship in a society where divorce is so common and the risk of divorce is collectively experienced.

Neuro- and immunotoxic effects of fumonisin B1 in cells

Fumonisin B1 (FB1) is a mycotoxin produced by the fungus Fusarium verticillioides, which commonly infects corn and other agricultural products. Fusarium species can also be found in moisture-damaged buildings, and therefore there may also be human exposure to Fusarium mycotoxins, including FB1. FB1 affects the metabolism of sphingolipids by inhibiting the enzyme ceramide synthase. It is neuro-, hepato- and nephrotoxic, and it is classified as possibly carcinogenic to humans. This study aimed to clarify the mechanisms behind FB1-induced neuro- and immunotoxicity. Four neural and glial cell lines of human, rat and mouse origin were exposed to graded doses of FB1 and the effects on the production of reactive oxygen species, lipid peroxidation, intracellular glutathione levels, cell viability and apoptosis were investigated. Furthermore, the effects of FB1, alone or together with lipopolysaccharide (LPS), on the mRNA and protein expression levels of different cytokines and chemokines were studied in human dendritic cells (DC). FB1 induced oxidative stress and cell death in all cell lines studied. Generally, the effects were only seen after prolonged exposure at 10 and 100 µM of FB1. Signs of apoptosis were also seen in all four cell lines. The sensitivities of the cell lines used in this study towards FB1 may be classified as human U-118MG glioblastoma > mouse GT1-7 hypothalamic > rat C6 glioblastoma > human SH-SY5Y neuroblastoma cells. When comparing cell lines of human origin, it can be concluded that glial cells seem to be more sensitive towards FB1 toxicity than those of neural origin. After exposure to FB1, significantly increased levels of the cytokine interferon-γ (IFNγ) were detected in human DC. This observation was further confirmed by FB1-induced levels of the chemokine CXCL9, which is known to be regulated by IFNγ. During co-exposure of DC to both LPS and FB1, significant inhibitions of the LPS-induced levels of the pro-inflammatory cytokines interleukin-6 (IL-6) and IL-1β, and their regulatory chemokines CCL3 and CCL5 were observed. FB1 can thus affect immune responses in DC, and therefore, it is rather likely that it also affects other types of cells participating in the immune defence system. When evaluating the toxicity potential of FB1, it is important to consider the effects on different cell types and cell-cell interactions. The results of this study represent new information, especially about the mechanisms behind FB1-induced oxidative stress, apoptosis and immunotoxicity, as well as the varying sensitivities of different cell types towards FB1.

Damp building moulds: Assessment of sensitization in patients and studies into mechanisms of airway inflammation using experimental models

Exposure to water-damaged buildings and the associated health problems have evoked concern and created confusion during the past 20 years. Individuals exposed to moisture problem buildings report adverse health effects such as non-specific respiratory symptoms. Microbes, especially fungi, growing on the damp material have been considered as potential sources of the health problems encountered in these buildings. Fungi and their airborne fungal spores contain allergens and secondary metabolites which may trigger allergic as well as inflammatory types of responses in the eyes and airways. Although epidemiological studies have revealed an association between damp buildings and health problems, no direct cause-and-effect relationship has been established. Further knowledge is needed about the epidemiology and the mechanisms leading to the symptoms associated with exposure to fungi. Two different approaches have been used in this thesis in order to investigate the diverse health effects associated with exposure to moulds. In the first part, sensitization to moulds was evaluated and potential cross-reactivity studied in patients attending a hospital for suspected allergy. In the second part, one typical mould known to be found in water-damaged buildings and to produce toxic secondary metabolites was used to study the airway responses in an experimental model. Exposure studies were performed on both naive and allergen sensitized mice. The first part of the study showed that mould allergy is rare and highly dependent on the atopic status of the examined individual. The prevalence of sensitization was 2.7% to Cladosporium herbarum and 2.8% to Alternaria alternata in patients, the majority of whom were atopic subjects. Some of the patients sensitized to mould suffered from atopic eczema. Frequently the patients were observed to possess specific serum IgE antibodies to a yeast present in the normal skin flora, Pityrosporum ovale. In some of these patients, the IgE binding was partly found to be due to binding to shared glycoproteins in the mould and yeast allergen extracts. The second part of the study revealed that exposure to Stachybotrys chartarum spores induced an airway inflammation in the lungs of mice. The inflammation was characterized by an influx of inflammatory cells, mainly neutrophils and lymphocytes, into the lungs but with almost no differences in airway responses seen between the satratoxin producing and non-satratoxin producing strain. On the other hand, when mice were exposed to S. chartarum and sensitized/challenged with ovalbumin the extent of the inflammation was markedly enhanced. A synergistic increase in the numbers of inflammatory cells was seen in BAL and severe inflammation was observed in the histological lung sections. In conclusion, the results in this thesis imply that exposure to moulds in water damaged buildings may trigger health effects in susceptible individuals. The symptoms can rarely be explained by IgE mediated allergy to moulds. Other non-allergic mechanisms seem to be involved. Stachybotrys chartarum is one of the moulds potentially responsible for health problems. In this thesis, new reaction models for the airway inflammation induced by S. chartarum have been found using experimental approaches. The immunological status played an important role in the airway inflammation, enhancing the effects of mould exposure. The results imply that sensitized individuals may be more susceptible to exposure to moulds than non-sensitized individuals.

Microbiological, environmental and proteolytic aspects in chronic rhinosinusitis with nasal polyposis

Chronic rhinosinusitis is one of the most common chronic respiratory tract diseases affecting up to 15% of the adult population in the Western world. It may be perpetuated by factors predisposing to sinus ostial obstruction together with inflammatory changes in the sinus mucosa. Chronic rhinosinusitis is associated with asthma, and it may represent the same disease process. Chronic rhinosinusitis with nasal polyposis (CRSwNP) and asthma share also the characteristic inflammatory features and histopathologic feature of airway remodelling. Remodelling is considered as a key event in the pathogenesis of asthma. It is controlled by a delicate balance between the matrix metalloproteinases (MMPs) and their regulators. The purpose of the present study was to evaluate the microbiological findings, inflammatory features and MMP and tissue inhibitor of metalloproteinases-1 (TIMP-1) expression in CRSwNP. The results were related to the patient history, exposure to moisture and clinical outcome in order to find out possible explanations for the etiology and chronicity of CRSwNP. Bacterial culture results were similar in patients and in controls and do not explain the chronic course of CRSwNP. The presence of fungi seems to be more common in CRSwNP than chronic rhinosinusitis in general, and they should be actively searched for using microbiological as well as histological methods. Typical outdoor fungal species were found in nasal lavage samples taken from controls in the autumn but not in the winter, reflecting environmental exposure. Exposure to moisture was reported by 46% of the CRSwNP patients, which is in accordance to the Finnish general population. Exposed patients did not differ significantly from non-exposed subjects with regards to microbiological findings, tissue eosinophilia and clinical outcome. Significantly elevated levels of collagenase-2 (MMP-8) and interleukin (IL)-8 but not tumour necrosis factor-α were found in CRSwNP patients. In particular, the activation of mesenchymal-type MMP-8 but not polymorphonuclear-type MMP-8 was associated with elevated IL-8 levels. IL-8 and MMP-8 may form an inductive cytokine-proteinase cascade in CRSwNP pathogenesis and provide a target for novel therapies and a diagnostic tool for monitoring CRSwNP treatment. The proteolytic spectrum is different in eosinophilic and non-eosinophilic CRSwNP with the up-regulation of MMP-8 and MMP-9 in non-eosinophilic CRSwNP, suggesting different pathophysiology in these subgroups. The lack of MMP up-regulation was associated with a poor prognostic factor and worse clinical outcome, representing a possible synergic anti-inflammatory function of MMP-8 and MMP-9 in CRSwNP. This study provides new information about possible immunologic mechanisms in the pathogenesis of CRSwNP. The recently discovered anti-inflammatory/ defensive properties of MMP-8 and MMP-9 in animal models are reported for the first time in a clinical setting in human inflammatory diseases.

Interfacial Phenomena in Pharmaceutical Low Moisture Content Powder Processing

Powders are essential materials in the pharmaceutical industry, being involved in majority of all drug manufacturing. Powder flow and particle size are central particle properties addressed by means of particle engineering. The aim of the thesis was to gain knowledge on powder processing with restricted liquid addition, with a primary focus on particle coating and early granule growth. Furthermore, characterisation of this kind of processes was performed. A thin coating layer of hydroxypropyl methylcellulose was applied on individual particles of ibuprofen in a fluidised bed top-spray process. The polymeric coating improved the flow properties of the powder. The improvement was strongly related to relative humidity, which can be seen as an indicator of a change in surface hydrophilicity caused by the coating. The ibuprofen used in the present study had a d50 of 40 μm and thus belongs to the Geldart group C powders, which can be considered as challenging materials in top-spray coating processes. Ibuprofen was similarly coated using a novel ultrasound-assisted coating method. The results were in line with those obtained from powders coated in the fluidised bed process mentioned above. It was found that the ultrasound-assisted method was capable of coating single particles with a simple and robust setup. Granule growth in a fluidised bed process was inhibited by feeding the liquid in pulses. The results showed that the length of the pulsing cycles is of importance, and can be used to adjust granule growth. Moreover, pulsed liquid feed was found to be of greater significance to granule growth in high inlet air relative humidity. Liquid feed pulsing can thus be used as a tool in particle size targeting in fluidised bed processes and in compensating for changes in relative humidity of the inlet air. The nozzle function of a two-fluid external mixing pneumatic nozzle, typical for small scale pharmaceutical fluidised bed processes, was studied in situ in an ongoing fluidised bed process with particle tracking velocimetry. It was found that the liquid droplets undergo coalescence as they proceed away from the nozzle head. The coalescence was expected to increase droplet speed, which was confirmed in the study. The spray turbulence was studied, and the results showed turbulence caused by the event of atomisation and by the oppositely directed fluidising air. It was concluded that particle tracking velocimetry is a suitable tool for in situ spray characterisation. The light transmission through dense particulate systems was found to carry information on particle size and packing density as expected based on the theory of light scattering by solids. It was possible to differentiate binary blends consisting of components with differences in optical properties. Light transmission showed potential as a rapid, simple and inexpensive tool in characterisation of particulate systems giving information on changes in particle systems, which could be utilised in basic process diagnostics.

Molecular profiling of indoor microbial communities in moisture damaged and non-damaged buildings

Epidemiological studies have shown an elevation in the incidence of asthma, allergic symptoms and respiratory infections among people living or working in buildings with moisture and mould problems. Microbial growth is suspected to have a key role, since the severity of microbial contamination and symptoms show a positive correlation, while the removal of contaminated materials relieves the symptoms. However, the cause-and-effect relationship has not been well established and knowledge of the causative agents is incomplete. The present consensus of indoor microbes relies on culture-based methods. Microbial cultivation and identification is known to provide qualitatively and quantitatively biased results, which is suspected to be one of the reasons behind the often inconsistent findings between objectively measured microbiological attributes and health. In the present study the indoor microbial communities were assessed using culture-independent, DNA based methods. Fungal and bacterial diversity was determined by amplifying and sequencing the nucITS- and16S-gene regions, correspondingly. In addition, the cell equivalent numbers of 69 mould species or groups were determined by quantitative PCR (qPCR). The results from molecular analyses were compared with results obtained using traditional plate cultivation for fungi. Using DNA-based tools, the indoor microbial diversity was found to be consistently higher and taxonomically wider than viable diversity. The dominant sequence types of fungi, and also of bacteria were mainly affiliated with well-known microbial species. However, in each building they were accompanied by various rare, uncultivable and unknown species. In both moisture-damaged and undamaged buildings the dominant fungal sequence phylotypes were affiliated with the classes Dothideomycetes (mould-like filamentous ascomycetes); Agaricomycetes (mushroom- and polypore-like filamentous basidiomycetes); Urediniomycetes (rust-like basidiomycetes); Tremellomycetes and the family Malasseziales (both yeast-like basidiomycetes). The most probable source for the majority of fungal types was the outdoor environment. In contrast, the dominant bacterial phylotypes in both damaged and undamaged buildings were affiliated with human-associated members within the phyla Actinobacteria and Firmicutes. Indications of elevated fungal diversity within potentially moisture-damage-associated fungal groups were recorded in two of the damaged buildings, while one of the buildings was characterized by an abundance of members of the Penicillium chrysogenum and P. commune species complexes. However, due to the small sample number and strong normal variation firm conclusions concerning the effect of moisture damage on the species diversity could not be made. The fungal communities in dust samples showed seasonal variation, which reflected the seasonal fluctuation of outdoor fungi. Seasonal variation of bacterial communities was less clear but to some extent attributable to the outdoor sources as well. The comparison of methods showed that clone library sequencing was a feasible method for describing the total microbial diversity, indicated a moderate quantitative correlation between sequencing and qPCR results and confirmed that culture based methods give both a qualitative and quantitative underestimate of microbial diversity in the indoor environment. However, certain important indoor fungi such as Penicillium spp. were clearly underrepresented in the sequence material, probably due to their physiological and genetic properties. Species specific qPCR was a more efficient and sensitive method for detecting and quantitating individual species than sequencing, but in order to exploit the full advantage of the method in building investigations more information is needed about the microbial species growing on damaged materials. In the present study, a new method was also developed for enhanced screening of the marker gene clone libraries. The suitability of the screening method to different kinds of microbial environments including biowaste compost material and indoor settled dusts was evaluated. The usability was found to be restricted to environments that support the growth and subsequent dominance of a small number microbial species, such as compost material.