Road Dust from Pavement Wear and Traction Sanding

Vehicles affect the concentrations of ambient airborne particles through exhaust emissions, but particles are also formed in the mechanical processes in the tire-road interface, brakes, and engine. Particles deposited on or in the vicinity of the road may be re-entrained, or resuspended, into air through vehicle-induced turbulence and shearing stress of the tires. A commonly used term for these particles is road dust . The processes affecting road dust emissions are complex and currently not well known. Road dust has been acknowledged as a dominant source of PM10 especially during spring in the sub-arctic urban areas, e.g. in Scandinavia, Finland, North America and Japan. The high proportion of road dust in sub-arctic regions of the world has been linked to the snowy winter conditions that make it necessary to use traction control methods. Traction control methods include dispersion of traction sand, melting of ice with brine solutions, and equipping the tires with either metal studs (studded winter tires), snow chains, or special tire design (friction tires). Several of these methods enhance the formation of mineral particles from pavement wear and/or from traction sand that accumulate in the road environment during winter. When snow and ice melt and surfaces dry out, traffic-induced turbulence makes some of the particles airborne. A general aim of this study was to study processes and factors underlying and affecting the formation and emissions of road dust from paved road surfaces. Special emphasis was placed on studying particle formation and sources during tire road interaction, especially when different applications of traction control, namely traction sanding and/or winter tires were in use. Respirable particles with aerodynamic diameter below 10 micrometers (PM10) have been the main concern, but other size ranges and particle size distributions were also studied. The following specific research questions were addressed: i) How do traction sanding and physical properties of the traction sand aggregate affect formation of road dust? ii) How do studded tires affect the formation of road dust when compared with friction tires? iii) What are the composition and sources of airborne road dust in a road simulator and during a springtime road dust episode in Finland? iv) What is the size distribution of abrasion particles from tire-road interaction? The studies were conducted both in a road simulator and in field conditions. The test results from the road simulator showed that traction sanding increased road dust emissions, and that the effect became more dominant with increasing sand load. A high percentage of fine-grained anti-skid aggregate of overall grading increased the PM10 concentrations. Anti-skid aggregate with poor resistance to fragmentation resulted in higher PM levels compared with the other aggregates, and the effect became more significant with higher aggregate loads. Glaciofluvial aggregates tended to cause higher particle concentrations than crushed rocks with good fragmentation resistance. Comparison of tire types showed that studded tires result in higher formation of PM emissions compared with friction tires. The same trend between the tires was present in the tests with and without anti-skid aggregate. This finding applies to test conditions of the road simulator with negligible resuspension. Source and composition analysis showed that the particles in the road simulator were mainly minerals and originated from both traction sand and pavement aggregates. A clear contribution of particles from anti-skid aggregate to ambient PM and dust deposition was also observed in urban conditions. The road simulator results showed that the interaction between tires, anti-skid aggregate and road surface is important in dust production and the relative contributions of these sources depend on their properties. Traction sand grains are fragmented into smaller particles under the tires, but they also wear the pavement aggregate. Therefore particles from both aggregates are observed. The mass size distribution of traction sand and pavement wear particles was mainly coarse, but fine and submicron particles were also present.

Locus Bonus : The Relationship of the Roman Villa to its Environment in the Vicinity of Rome

The aim of this study is to examine the relationship of the Roman villa to its environment. The villa was an important feature of the countryside intended both for agricultural production and for leisure. Manuals of Roman agriculture give instructions on how to select a location for an estate. The ideal location was a moderate slope facing east or south in a healthy area and good neighborhood, near good water resources and fertile soils. A road or a navigable river or the sea was needed for transportation of produce. A market for selling the produce, a town or a village, should have been nearby. The research area is the surroundings of the city of Rome, a key area for the development of the villa. The materials used consist of archaeological settlement sites, literary and epigraphical evidence as well as environmental data. The sites include all settlement sites from the 7th century BC to 5th century AD to examine changes in the tradition of site selection. Geographical Information Systems were used to analyze the data. Six aspects of location were examined: geology, soils, water resources, terrain, visibility/viewability and relationship to roads and habitation centers. Geology was important for finding building materials and the large villas from the 2nd century BC onwards are close to sources of building stones. Fertile soils were sought even in the period of the densest settlement. The area is rich in water, both rainfall and groundwater, and finding a water supply was fairly easy. A certain kind of terrain was sought over very long periods: a small spur or ridge shoulder facing preferably south with an open area in front of the site. The most popular villa resorts are located on the slopes visible from almost the entire Roman region. A visible villa served the social and political aspirations of the owner, whereas being in the villa created a sense of privacy. The area has a very dense road network ensuring good connectivity from almost anywhere in the region. The best visibility/viewability, dense settlement and most burials by roads coincide, creating a good neighborhood. The locations featuring the most qualities cover nearly a quarter of the area and more than half of the settlement sites are located in them. The ideal location was based on centuries of practical experience and rationalized by the literary tradition.