Studies on diamond-like carbon and novel diamond-like carbon polymer hybrid coatings deposited with filtered pulsed arc discharge method

The main obstacle for the application of high quality diamond-like carbon (DLC) coatings has been the lack of adhesion to the substrate as the coating thickness is increased. The aim of this study was to improve the filtered pulsed arc discharge (FPAD) method. With this method it is possible to achieve high DLC coating thicknesses necessary for practical applications. The energy of the carbon ions was measured with an optoelectronic time-of-flight method. An in situ cathode polishing system used for stabilizing the process yield and the carbon ion energies is presented. Simultaneously the quality of the coatings can be controlled. To optimise the quality of the deposition process a simple, fast and inexpensive method using silicon wafers as test substrates was developed. This method was used for evaluating the suitability of a simplified arc-discharge set-up for the deposition of the adhesion layer of DLC coatings. A whole new group of materials discovered by our research group, the diamond-like carbon polymer hybrid (DLC-p-h) coatings, is also presented. The parent polymers used in these novel coatings were polydimethylsiloxane (PDMS) and polytetrafluoroethylene (PTFE). The energy of the plasma ions was found to increase when the anode-cathode distance and the arc voltage were increased. A constant deposition rate for continuous coating runs was obtained with an in situ cathode polishing system. The novel DLC-p-h coatings were found to be water and oil repellent and harder than any polymers. The lowest sliding angle ever measured from a solid surface, 0.15 ± 0.03°, was measured on a DLC-PDMS-h coating. In the FPAD system carbon ions can be accelerated to high energies (≈ 1 keV) necessary for the optimal adhesion (the substrate is broken in the adhesion and quality test) of ultra thick (up to 200 µm) DLC coatings by increasing the anode-cathode distance and using high voltages (up to 4 kV). An excellent adhesion can also be obtained with the simplified arc-discharge device. To maintain high process yield (5µm/h over a surface area of 150 cm2) and to stabilize the carbon ion energies and the high quality (sp3 fraction up to 85%) of the resulting coating, an in situ cathode polishing system must be used. DLC-PDMS-h coating is the superior candidate coating material for anti-soiling applications where also hardness is required.

Understanding solid-state transformations during dehydration: new insights using vibrational spectroscopy and multivariate modelling

Many active pharmaceutical ingredients (APIs) have both anhydrate and hydrate forms. Due to the different physicochemical properties of solid forms, the changes in solid-state may result in therapeutic, pharmaceutical, legal and commercial problems. In order to obtain good solid dosage form quality and performance, there is a constant need to understand and control these phase transitions during manufacturing and storage. Thus it is important to detect and also quantify the possible transitions between the different forms. In recent years, vibrational spectroscopy has become an increasingly popular tool to characterise the solid-state forms and their phase transitions. It offers several advantages over other characterisation techniques including an ability to obtain molecular level information, minimal sample preparation, and the possibility of monitoring changes non-destructively in-line. Dehydration is the phase transition of hydrates which is frequently encountered during the dosage form production and storage. The aim of the present thesis was to investigate the dehydration behaviour of diverse pharmaceutical hydrates by near infrared (NIR), Raman and terahertz pulsed spectroscopic (TPS) monitoring together with multivariate data analysis. The goal was to reveal new perspectives for investigation of the dehydration at the molecular level. Solid-state transformations were monitored during dehydration of diverse hydrates on hot-stage. The results obtained from qualitative experiments were used to develop a method and perform the quantification of the solid-state forms during process induced dehydration in a fluidised bed dryer. Both in situ and in-line process monitoring and quantification was performed. This thesis demonstrated the utility of vibrational spectroscopy techniques and multivariate modelling to monitor and investigate dehydration behaviour in situ and during fluidised bed drying. All three spectroscopic methods proved complementary in the study of dehydration. NIR spectroscopy models could quantify the solid-state forms in the binary system, but were unable to quantify all the forms in the quaternary system. Raman spectroscopy models on the other hand could quantify all four solid-state forms that appeared upon isothermal dehydration. The speed of spectroscopic methods makes them applicable for monitoring dehydration and the quantification of multiple forms was performed during phase transition. Thus the solid-state structure information at the molecular level was directly obtained. TPS detected the intermolecular phonon modes and Raman spectroscopy detected mostly the changes in intramolecular vibrations. Both techniques revealed information about the crystal structure changes. NIR spectroscopy, on the other hand was more sensitive to water content and hydrogen bonding environment of water molecules. This study provides a basis for real time process monitoring using vibrational spectroscopy during pharmaceutical manufacturing.

Investigating physical properties of solid dosage forms during pharmaceutical processing : Process analytical applications of vibrational spectroscopy

In order to improve and continuously develop the quality of pharmaceutical products, the process analytical technology (PAT) framework has been adopted by the US Food and Drug Administration. One of the aims of PAT is to identify critical process parameters and their effect on the quality of the final product. Real time analysis of the process data enables better control of the processes to obtain a high quality product. The main purpose of this work was to monitor crucial pharmaceutical unit operations (from blending to coating) and to examine the effect of processing on solid-state transformations and physical properties. The tools used were near-infrared (NIR) and Raman spectroscopy combined with multivariate data analysis, as well as X-ray powder diffraction (XRPD) and terahertz pulsed imaging (TPI). To detect process-induced transformations in active pharmaceutical ingredients (APIs), samples were taken after blending, granulation, extrusion, spheronisation, and drying. These samples were monitored by XRPD, Raman, and NIR spectroscopy showing hydrate formation in the case of theophylline and nitrofurantoin. For erythromycin dihydrate formation of the isomorphic dehydrate was critical. Thus, the main focus was on the drying process. NIR spectroscopy was applied in-line during a fluid-bed drying process. Multivariate data analysis (principal component analysis) enabled detection of the dehydrate formation at temperatures above 45°C. Furthermore, a small-scale rotating plate device was tested to provide an insight into film coating. The process was monitored using NIR spectroscopy. A calibration model, using partial least squares regression, was set up and applied to data obtained by in-line NIR measurements of a coating drum process. The predicted coating thickness agreed with the measured coating thickness. For investigating the quality of film coatings TPI was used to create a 3-D image of a coated tablet. With this technique it was possible to determine coating layer thickness, distribution, reproducibility, and uniformity. In addition, it was possible to localise defects of either the coating or the tablet. It can be concluded from this work that the applied techniques increased the understanding of physico-chemical properties of drugs and drug products during and after processing. They additionally provided useful information to improve and verify the quality of pharmaceutical dosage forms

Modern techniques in detection, identification and quantification of bacteria and peptides from foods

Standards have been placed to regulate the microbial and preservative contents to assure that foods are safe to the consumer. In a case of a food-related disease outbreak, it is crucial to be able to detect and identify quickly and accurately the cause of the disease. In addition, for every day control of food microbial and preservative contents, the detection methods must be easily performed for numerous food samples. In this present study, quicker alternative methods were studied for identification of bacteria by DNA fingerprinting. A flow cytometry method was developed as an alternative to pulsed-field gel electrophoresis, the golden method . DNA fragment sizing by an ultrasensitive flow cytometer was able to discriminate species and strains in a reproducible and comparable manner to pulsed-field gel electrophoresis. This new method was hundreds times faster and 200,000 times more sensitive. Additionally, another DNA fingerprinting identification method was developed based on single-enzyme amplified fragment length polymorphism (SE-AFLP). This method allowed the differentiation of genera, species, and strains of pathogenic bacteria of Bacilli, Staphylococci, Yersinia, and Escherichia coli. These fingerprinting patterns obtained by SE-AFLP were simpler and easier to analyze than those by the traditional amplified fragment length polymorphism by double enzyme digestion. Nisin (E234) is added as a preservative to different types of foods, especially dairy products, around the world. Various detection methods exist for nisin, but they lack in sensitivity, speed or specificity. In this present study, a sensitive nisin-induced green fluorescent protein (GFPuv) bioassay was developed using the Lactococcus lactis two-component signal system NisRK and the nisin-inducible nisA promoter. The bioassay was extremely sensitive with detection limit of 10 pg/ml in culture supernatant. In addition, it was compatible for quantification from various food matrices, such as milk, salad dressings, processed cheese, liquid eggs, and canned tomatoes. Wine has good antimicrobial properties due to its alcohol concentration, low pH, and organic content and therefore often assumed to be microbially safe to consume. Another aim of this thesis was to study the microbiota of wines returned by customers complaining of food-poisoning symptoms. By partial 16S rRNA gene sequence analysis, ribotyping, and boar spermatozoa motility assay, it was identified that one of the wines contained a Bacillus simplex BAC91, which produced a heat-stable substance toxic to the mitochondria of sperm cells. The antibacterial activity of wine was tested on the vegetative cells and spores of B. simplex BAC91, B. cereus type strain ATCC 14579 and cereulide-producing B. cereus F4810/72. Although the vegetative cells and spores of B. simplex BAC91 were sensitive to the antimicrobial effects of wine, the spores of B. cereus strains ATCC 14579 and F4810/72 stayed viable for at least 4 months. According to these results, Bacillus spp., more specifically spores, can be a possible risk to the wine consumer.

Preparation, structural analysis and prebiotic potential of arabinoxylo-oligosaccharides

Arabinoxylo-oligosaccharides (AXOS) can be prepared enzymatically from arabinoxylans (AX) and AXOS are known to possess prebiotic potential. Here the structural features of 10 cereal AX were examined. AX were hydrolysed by Shearzyme® to prepare AXOS, and their structures were fully analysed. The prebiotic potential of the purified AXOS was studied in the fermentation experiments with bifidobacteria and faecal microbiota. In AX extracted from flours and bran, high amounts of a-L-Araf units are attached to the b-D-Xylp main chain, whereas moderate or low degree of substitution was found from husks, cob and straw. Nuclear magnetic resonance (NMR) spectroscopy showed that flour and bran AX contain high amounts of a-L-Araf units bound to the O-3 of b-D-Xylp residues and doubly substituted b-D-Xylp units with a-L-Araf substituents at O-2 and O-3. Barley husk and corn cob AX contain high amounts of b-D-Xylp(1→2)-a-L-Araf(1→3) side chains, which can also be found in AX from oat spelts and rice husks, and in lesser amounts in wheat straw AX. Rye and wheat flour AX and oat spelt AX were hydrolysed by Shearzyme® (with Aspergillus aculeatus GH10 endo-1,4-b-D-xylanase as the main enzyme) for the production of AXOS on a milligram scale. The AXOS were purified and their structures fully analysed, using mass spectrometry (MS) and 1D and 2D NMR spectroscopy. Monosubstituted xylobiose and xylotriose with a-L-Araf attached to the O-3 or O-2 of the nonreducing end b-D-Xylp unit and disubstituted AXOS with two a-L-Araf units at the nonreducing end b-D-Xylp unit of xylobiose or xylotriose were produced. Xylobiose with b-D-Xylp(1→2)-a-L-Araf(1→3) side chain was also purified. These AXOS were used as standards in further identification and quantification of corresponding AXOS from the hydrolysates in high-performance anion-exchange chromatography with pulsed amperometric detection (HPAEC-PAD) analysis. The prebiotic potential of AXOS was tested in in vitro fermentation experiments. Bifidobacterium adolescentis ATCC 15703 and B. longum ATCC 15707 utilized AXOS from the AX hydrolysates. Both species released L-arabinose from AXOS, but B. adolescentis consumed the XOS formed, whereas B. longum fermented the L-arabinose released. The third species tested, B. breve ATCC 15700, grew poorly on these substrates. When cultivated on pure AXOS, the bifidobacterial mixture utilized pure singly substituted AXOS almost completely, but no growth was detected with pure doubly substituted AXOS as substrates. However, doubly substituted AXOS were utilized from the mixture of xylose, XOS and AXOS. Faecal microbiota utilized both pure singly and doubly substituted AXOS. Thus, a mixture of singly and doubly substituted AXOS could function as a suitable, slowly fermenting prebiotic substance. This thesis contributes to the structural information on cereal AX and preparation of mono and doubly substituted AXOS from AX. Understanding the utilization strategies is fundamental in evaluating the prebiotic potential of AXOS. Further research is still required before AXOS can be used in applications for human consumption.

The kinetics and reactivity of several polyatomic free radicals in reactions with NO2, O2, Cl2, and HCl

In this thesis, the kinetics of several alkyl, halogenated alkyl, and alkenyl free radical reactions with NO2, O2, Cl2, and HCl reactants were studied over a wide temperature range in time resolved conditions. Laser photolysis photoionisation mass spectrometer coupled to a flow reactor was the experimental method employed and this thesis present the first measurements performed with the experimental system constructed. During this thesis a great amount of work was devoted to the designing, building, testing, and improving the experimental apparatus. Carbon-centred free radicals were generated by the pulsed 193 or 248 nm photolysis of suitable precursors along the tubular reactor. The kinetics was studied under pseudo-first-order conditions using either He or N2 buffer gas. The temperature and pressure ranges employed were between 190 and 500 K, and 0.5 45 torr, respectively. The possible role of heterogeneous wall reactions was investigated employing reactor tubes with different sizes, i.e. to significantly vary the surface to volume ratio. In this thesis, significant new contributions to the kinetics of carbon-centred free radical reactions with nitrogen dioxide were obtained. Altogether eight substituted alkyl (CH2Cl, CHCl2, CCl3, CH2I, CH2Br, CHBr2, CHBrCl, and CHBrCH3) and two alkenyl (C2H3, C3H3) free radical reactions with NO2 were investigated as a function of temperature. The bimolecular rate coefficients of all these reactions were observed to possess negative temperature dependencies, while pressure dependencies were not noticed for any of these reactions. Halogen substitution was observed to moderately reduce the reactivity of substituted alkyl radicals in the reaction with NO2, while the resonance stabilisation of the alkenyl radical lowers its reactivity with respect to NO2 only slightly. Two reactions relevant to atmospheric chemistry, CH2Br + O2 and CH2I + O2, were also investigated. It was noticed that while CH2Br + O2 reaction shows pronounced pressure dependence, characteristic of peroxy radical formation, no such dependence was observed for the CH2I + O2 reaction. Observed primary products of the CH2I + O2 reaction were the I-atom and the IO radical. Kinetics of CH3 + HCl, CD3 + HCl, CH3 + DCl, and CD3 + DCl reactions were also studied. While all these reactions possess positive activation energies, in contrast to the other systems investigated in this thesis, the CH3 + HCl and CD3 + HCl reactions show a non-linear temperature dependency on the Arrhenius plot. The reactivity of substituted methyl radicals toward NO2 was observed to increase with decreasing electron affinity of the radical. The same trend was observed for the reactions of substituted methyl radicals with Cl2. It is proposed that interactions of frontier orbitals are responsible to these observations and Frontier Orbital Theory could be used to explain the observed reactivity trends of these highly exothermic reactions having reactant-like transition states.

Comprehensive Two-Dimensional Gas Chromatography: Instrumental and Methodological Development

Comprehensive two-dimensional gas chromatography (GC×GC) offers enhanced separation efficiency, reliability in qualitative and quantitative analysis, capability to detect low quantities, and information on the whole sample and its components. These features are essential in the analysis of complex samples, in which the number of compounds may be large or the analytes of interest are present at trace level. This study involved the development of instrumentation, data analysis programs and methodologies for GC×GC and their application in studies on qualitative and quantitative aspects of GC×GC analysis. Environmental samples were used as model samples. Instrumental development comprised the construction of three versions of a semi-rotating cryogenic modulator in which modulation was based on two-step cryogenic trapping with continuously flowing carbon dioxide as coolant. Two-step trapping was achieved by rotating the nozzle spraying the carbon dioxide with a motor. The fastest rotation and highest modulation frequency were achieved with a permanent magnetic motor, and modulation was most accurate when the motor was controlled with a microcontroller containing a quartz crystal. Heated wire resistors were unnecessary for the desorption step when liquid carbon dioxide was used as coolant. With use of the modulators developed in this study, the narrowest peaks were 75 ms at base. Three data analysis programs were developed allowing basic, comparison and identification operations. Basic operations enabled the visualisation of two-dimensional plots and the determination of retention times, peak heights and volumes. The overlaying feature in the comparison program allowed easy comparison of 2D plots. An automated identification procedure based on mass spectra and retention parameters allowed the qualitative analysis of data obtained by GC×GC and time-of-flight mass spectrometry. In the methodological development, sample preparation (extraction and clean-up) and GC×GC methods were developed for the analysis of atmospheric aerosol and sediment samples. Dynamic sonication assisted extraction was well suited for atmospheric aerosols collected on a filter. A clean-up procedure utilising normal phase liquid chromatography with ultra violet detection worked well in the removal of aliphatic hydrocarbons from a sediment extract. GC×GC with flame ionisation detection or quadrupole mass spectrometry provided good reliability in the qualitative analysis of target analytes. However, GC×GC with time-of-flight mass spectrometry was needed in the analysis of unknowns. The automated identification procedure that was developed was efficient in the analysis of large data files, but manual search and analyst knowledge are invaluable as well. Quantitative analysis was examined in terms of calibration procedures and the effect of matrix compounds on GC×GC separation. In addition to calibration in GC×GC with summed peak areas or peak volumes, simplified area calibration based on normal GC signal can be used to quantify compounds in samples analysed by GC×GC so long as certain qualitative and quantitative prerequisites are met. In a study of the effect of matrix compounds on GC×GC separation, it was shown that quality of the separation of PAHs is not significantly disturbed by the amount of matrix and quantitativeness suffers only slightly in the presence of matrix and when the amount of target compounds is low. The benefits of GC×GC in the analysis of complex samples easily overcome some minor drawbacks of the technique. The developed instrumentation and methodologies performed well for environmental samples, but they could also be applied for other complex samples.

Eru Ilúvatar : Jumala J.R.R. Tolkienin legendariumissa

The purpose of my research is to inquire into the essence and activity of God in the legendarium of the English philologist and writer J.R.R. Tolkien (1892-1973). The legendarium, composed of Tolkien’s writings related to Middle-earth, was begun when he created two Elvish languages, Quenya based on Finnish, Sindarin based on Welsh. Tolkien developed his mythology inspired by Germanic myths and The Kalevala. It is a fictional ancient history set in our world. The legendarium is monotheistic: God is called Eru ‘The One’ and Ilúvatar ‘Father of All’. Eru is the same as the Christian God, for Tolkien wanted to keep his tales consistent with his faith. He said his works were Christian by nature, with the religious element absorbed into the story and the symbolism. In The Silmarillion, set in the primeval ages of Middle-earth, the theological aspects are more conspicuous, while in The Lord of the Rings, which brings the stories to an end, they are mostly limited to symbolic references. The legendarium is unified by its realistic outlook on creaturely abilities and hope expressing itself as humbly defiant resistance. ”The possibility of complexity or of distinctions in the nature of Eru” is a part of the legendarium. Eru Ilúvatar is Trinitarian, as per Tolkien’s faith. Without contextual qualifiers, Eru seems to refer to God the Father, like God in the Bible. Being the creator who dwells outside the world is attributed to Him. The Holy Spirit is the only Person of the Trinity bestown with names: the Flame Imperishable and the Secret Fire. When Eru creates the material world with His word, He sends the Flame Imperishable to burn at the heart of the world. The Secret Fire signifies the Creative Power that belongs to God alone, and is a part of Him. The Son, the Word, is not directly mentioned, but according to one writing Eru must step inside the world in order to save it from corruption, yet remain outside it at the same time. The inner structure of the legendarium refers to the need for a future salvation. The creative word of Eru, “Eä! Let these things Be!”, probably has a connection with the Logos in Christianity. Thus we can find three “distinctions” in Eru: a Creator who dwells outside the world, a Sustainer who dwells inside it and a Redeemer who shall step inside it. Some studies of Tolkien have claimed that Eru is distant and remote. This seems to hold water only partially. Ilúvatar, the Father of All, has a special relation with the Eruhíni, His Children, the immortal Elves and the mortal Men. He communicates with them directly only through the Valar, who resemble archangels. Nevertheless, only the Children of Eru can fight against evil, because their tragic fortunes turn evil into good. Even though religious activities are scarce among them, the fundamental faith and ultimate hope of the “Free Peoples” is directed towards Eru. He is present in the drama of history as the “Author of the Story”, who at times also interferes with its course through catastrophes and eucatastrophes, ‘good catastrophes’. Eru brings about a catastrophe when evil would otherwise bring good to an end, and He brings about a eucatasrophe when creaturely strength is not sufficent for victory. Victory over corruption is especially connected with mortal Men, of whom the most (or least) insignificant people are the Hobbits. However, because of the “primeval disaster” (that is, fall) of Mankind, ultimate salvation can only remain open, a hope for the far future.

Methicillin-resistant Staphylococcus aureus in Finland: recent changes in the epidemiology, long-term facility aspects, and phenotypic and molecular detection of isolates

Staphylococcus aureus is one of the most important bacteria that cause disease in humans, and methicillin-resistant S. aureus (MRSA) has become the most commonly identified antibiotic-resistant pathogen in many parts of the world. MRSA rates have been stable for many years in the Nordic countries and the Netherlands with a low MRSA prevalence in Europe, but in the recent decades, MRSA rates have increased in those low-prevalence countries as well. MRSA has been established as a major hospital pathogen, but has also been found increasingly in long-term facilities (LTF) and in communities of persons with no connections to the health-care setting. In Finland, the annual number of MRSA isolates reported to the National Infectious Disease Register (NIDR) has constantly increased, especially outside the Helsinki metropolitan area. Molecular typing has revealed numerous outbreak strains of MRSA, some of which have previously been associated with community acquisition. In this work, data on MRSA cases notified to the NIDR and on MRSA strain types identified with pulsed-field gel electrophoresis (PFGE), multilocus sequence typing (MLST), and staphylococcal cassette chromosome mec (SCCmec) typing at the National Reference Laboratory (NRL) in Finland from 1997 to 2004 were analyzed. An increasing trend in MRSA incidence in Finland from 1997 to 2004 was shown. In addition, non-multi-drug resistant (NMDR) MRSA isolates, especially those resistant only to methicillin/oxacillin, showed an emerging trend. The predominant MRSA strains changed over time and place, but two internationally spread epidemic strains of MRSA, FIN-16 and FIN-21, were related to the increase detected most recently. Those strains were also one cause of the strikingly increasing invasive MRSA findings. The rise of MRSA strains with SCCmec types IV or V, possible community-acquired MRSA was also detected. With questionnaires, the diagnostic methods used for MRSA identification in Finnish microbiology laboratories and the number of MRSA screening specimens studied were reviewed. Surveys, which focused on the MRSA situation in long-term facilities in 2001 and on the background information of MRSA-positive persons in 2001-2003, were also carried out. The rates of MRSA and screening practices varied widely across geographic regions. Part of the NMDR MRSA strains could remain undetected in some laboratories because of insufficient diagnostic techniques used. The increasing proportion of elderly population carrying MRSA suggests that MRSA is an emerging problem in Finnish long-term facilities. Among the patients, 50% of the specimens were taken on a clinical basis, 43% on a screening basis after exposure to MRSA, 3% on a screening basis because of hospital contact abroad, and 4% for other reasons. In response to an outbreak of MRSA possessing a new genotype that occurred in a health care ward and in an associated nursing home of a small municipality in Northern Finland in autumn 2003, a point-prevalence survey was performed six months later. In the same study, the molecular epidemiology of MRSA and methicillin-sensitive S. aureus (MSSA) strains were also assessed, the results to the national strain collection compared, and the difficulties of MRSA screening with low-level oxacillin-resistant isolates encountered. The original MRSA outbreak in LTF, which consisted of isolates possessing a nationally new PFGE profile (FIN-22) and internationally rare MLST type (ST-27), was confined. Another previously unrecognized MRSA strain was found with additional screening, possibly indicating that current routine MRSA screening methods may be insufficiently sensitive for strains possessing low-level oxacillin resistance. Most of the MSSA strains found were genotypically related to the epidemic MRSA strains, but only a few of them had received the SCCmec element, and all those strains possessed the new SCCmec type V. In the second largest nursing home in Finland, the colonization of S. aureus and MRSA, and the role of screening sites along with broth enrichment culture on the sensitivity to detect S. aureus were studied. Combining the use of enrichment broth and perineal swabbing, in addition to nostrils and skin lesions swabbing, may be an alternative for throat swabs in the nursing home setting, especially when residents are uncooperative. Finally, in order to evaluate adequate phenotypic and genotypic methods needed for reliable laboratory diagnostics of MRSA, oxacillin disk diffusion and MIC tests to the cefoxitin disk diffusion method at both +35°C and +30°C, both with or without an addition of sodium chloride (NaCl) to the Müller Hinton test medium, and in-house PCR to two commercial molecular methods (the GenoType® MRSA test and the EVIGENETM MRSA Detection test) with different bacterial species in addition to S. aureus were compared. The cefoxitin disk diffusion method was superior to that of oxacillin disk diffusion and to the MIC tests in predicting mecA-mediated resistance in S. aureus when incubating at +35°C with or without the addition of NaCl to the test medium. Both the Geno Type® MRSA and EVIGENETM MRSA Detection tests are usable, accurate, cost-effective, and sufficiently fast methods for rapid MRSA confirmation from a pure culture.

The effects of low-intensity ultrasound in bioabsorbable self-reinforced poly-L-lactide -fixed cancellous bone fracture

The purpose of the present study was to investigate the effects of low-intensity ultrasound on bioabsorbable self-reinforced poly-L-lactide (SR-PLLA) screws and on fracture healing after SR-PLLA device fixation in experimental and clinical cancellous bone fracture. In the first experimental study, the assessment of the mechanical strengths of the SR-PLLA screws was performed after 12 weeks of daily 20-minute ultrasound exposure in vitro. In the second experimental study, 32 male Wistar rats with an experimental distal femur osteotomy fixed with an SR-PLLA rod were exposed for daily low-intensity ultrasound treatment for 21 days. The effects on the healing bone were assessed. The clinical studies consist of three prospective, randomized, and placebo-controlled series of dislocated lateral malleolar fractures fixed with one SR-PLLA screw. The total number of the patients in these series was 52. Half of the patients were provided randomly with a sham ultrasound device. The patients underwent ultrasound therapy 20 minutes daily for six weeks. Radiological bone healing was assessed both by radiographs at two, six, nine, and 12 weeks and by multidetector computed tomography (MDCT) scans at two weeks, nine weeks, and 18 months. Bone mineral density was assessed by dual-energy X-ray absorptiometry (DXA). The clinical outcome was assessed by both Olerud-Molander scoring and clinical examination of the ankle. Low-intensity ultrasound had no effects on the mechanical properties and degradation behaviour of the SR-PLLA screws in vitro. There were no obvious signs of low-intensity ultrasound-induced enhancement in the bone healing in SR-PLLA-rod-fixed metaphyseal distal femur osteotomy in rats. The biocompatibility of low-intensity ultrasound treatment and SR-PLLA was found to be good. In the clinical series low-intensity ultrasound was observed to have no obvious effects on the bone mineral density of the fractured lateral malleolus. There were no obvious differences in the radiological bone healing times of the SR-PLLA-screw-fixed lateral malleolar fractures after low-intensity ultrasound treatment. Low-intensity ultrasound did not have any effects on radiological bone morphology, bone mineral density or clinical outcome 18 months after the injury. There were no obvious findings in the present study to support the hypothesis that low-intensity pulsed ultrasound enhances bone healing in SR-PLLA-rod-fixed experimental metaphyseal distal femur osteotomy in rats or in clinical SR-PLLA-screw-fixed lateral malleolar fractures. It is important to limit the conclusions of the present set of studies only to lateral malleolar fractures fixed with an SR-PLLA screw.

Leuconostoc spoilage of refrigerated, packaged foods

Leuconostoc spp. are lactic acid bacteria (LAB) implicated in food spoilage, especially on refrigerated, modified atmosphere packaged (MAP) meats. The overall aim of this thesis was to learn more about Leuconostoc spp. as food spoilage organisms with a focus on commercial products where LAB spoilage is considered a problem and the main factor limiting shelf-life. Therefore, we aimed to identify Leuconostoc spp. involved in food spoilage, as well as to characterise the spoilage reactions they caused and their contamination sources during poultry meat processing. In addition, we examined the distribution of strains of Leuconostoc gasicomitatum in different food commodities. Finally, we analysed the genome content of L. gasicomitatum LMG 18811 with a special focus on metabolic pathways related to food spoilage. The findings show that Leuconostoc gelidum and L.gasicomitatum were responsible for the discoloration and off-odours developed in beef steaks. Together with Leuconostoc mesenteroides, these Leuconostoc spp., also cause spoilage of vegetable sausages. In contrast, we showed that Leuconostoc spp. are not important for the shelf-life or quality of non-marinated broiler products although, in marinated broiler fillet products, Leuconostoc spp., L.gasicomitatum in particular, are considered spoilage organisms. Furthermore, the findings of the contamination survey we carried out in a poultry processing plant indicated that spoilage Leuconostoc spp. are derived from the processing environment rather than from the broilers, and that air movement distributes psychrotrophic spoilage LAB, including leuconostocs, and has an important role in meat contamination during poultry processing. Pulsed-field gel electrophoresis (PFGE) based genotyping of L. gasicomitatum strains demonstrated that certain genotypes are common in various meat products. In contrast, genotypes associated with meat were not recovered in vegetable-based sources. This suggests that these two food categories either become contaminated with, or favour the growth of different genotypes. Furthermore, the results indicated that the meat processing environment contributes to L. gasicomitatum contamination as certain genotypes were repeatedly identified from products of the same processing plant. Finally, the sequenced and annotated genome of L.gasicomitatum LMG 18811 allowed us to identify the metabolic pathways and reactions resulting in food spoilage.

Adhesion,Presence and Antifouling of Deinococcus geothermalis in Paper Machine Environment

This thesis has two items: biofouling and antifouling in paper industry. Biofouling means unwanted microbial accumulation on surfaces causing e.g. disturbances in industrial processes, contamination of medical devices or of water distribution networks. Antifouling focuses on preventing accumulation of the biofilms in undesired places. Deinococcus geothermalis is a pink-pigmented, thermophilic bacterium, and extremely resistant towards radiation, UV-light and desiccation and known as a biofouler of paper machines forming firm and biocide resistant biofilms on the stainless steel surfaces. The compact structure of biofilm microcolonies of D. geothermalis E50051 and the adhesion into abiotic surfaces were investigated by confocal laser scanning microscope combined with carbohydrate specific fluorescently labelled lectins. The extracellular polymeric substance in D. geothermalis microcolonies was found to be a composite of at least five different glycoconjugates contributing to adhesion, functioning as structural elements, putative storages for water, gliding motility and likely also to protection. The adhesion threads that D. geothermalis seems to use to adhere on an abiotic surface and to anchor itself to the neighbouring cells were shown to be protein. Four protein components of type IV pilin were identified. In addition, the lectin staining showed that the adhesion threads were covered with galactose containing glycoconjugates. The threads were not exposed on planktic cells indicating their primary role in adhesion and in biofilm formation. I investigated by quantitative real-time PCR the presence of D. geothermalis in biofilms, deposits, process waters and paper end products from 24 paper and board mills. The primers designed for doing this were targeted to the 16S rRNA gene of D. geothermalis. We found D. geothermalis DNA from 9 machines, in total 16 samples of the 120 mill samples searched for. The total bacterial content varied in those samples between 107 to 3 ×1010 16S rRNA gene copies g-1. The proportion of D. geothermalis in those same samples was minor, 0.03 1.3 % of the total bacterial content. Nevertheless D. geothermalis may endanger paper quality as its DNA was shown in an end product. As an antifouling method towards biofilms we studied the electrochemical polarization. Two novel instruments were designed for this work. The double biofilm analyzer was designed for search for a polarization program that would eradicate D. geothermalis biofilm or from stainless steel under conditions simulating paper mill environment. The Radbox instrument was designed to study the generation of reactive oxygen species during the polarization that was effective in antifouling of D. geothermalis. We found that cathodic character and a pulsed mode of polarization were required to achieve detaching D. geothermalis biofilm from stainless steel. We also found that the efficiency of polarization was good on submerged, and poor on splash area biofilms. By adding oxidative biocides, bromochloro-5,5-dimethylhydantoin, 2,2-dibromo-2-cyanodiacetamide or peracetic acid gave additive value with polarization, being active on splash area biofilms. We showed that the cathodically weighted pulsed polarization that was active in removing D. geothermalis was also effective in generation of reactive oxygen species. It is possible that the antifouling effect relied on the generation of ROS on the polarized steel surfaces. Antifouling method successful towards D. geothermalis that is a tenacious biofouler and possesses a high tolerance to oxidative stressors could be functional also towards other biofoulers and applicable in wet industrial processes elsewhere.

Finnish cattle as reservoir of Campylobacter spp.

The reported incidence of human campylobacteriosis in Finland is higher than in most other European countries. A high annual percentage of sporadic infections is of foreign origin, although a notable proportion of summer infections is domestically acquired. While chickens appear to be a major source of campylobacters for humans in most countries, the prevalence of campylobacters is very low in chicken slaughter batches in Finland. Data on other potential animal reservoirs of human pathogenic campylobacters in Finland are scarce. Consequently, this study aimed to investigate the status of Finnish cattle as a potential source of thermophilic Campylobacter spp. and antibiotic-resistant Campylobacter jejuni for human sporadic campylobacter infections of domestic origin. A survey of the prevalence of thermophilic Campylobacter spp. in Finnish cattle studied bovine rectal faecal samples (n=952) and carcass surface samples (n=948) from twelve Finnish slaughterhouses from January to December 2003. The total prevalence of Campylobacter spp. in faecal samples was 31.1%, and in carcass samples 3.5%. Campylobacter jejuni, the most common species, was present in 19.5% of faecal samples and in 3.1% of carcasses. In addition to thermophilic Campylobacter spp., C. hyointestinalis ssp. hyointestinalis was present in bovine samples. The prevalence of campylobacters was higher among beef cattle than among dairy cattle. Using the enrichment method, the number of positive faecal samples was 7.5 times higher than that obtained by direct plating. The predominant serotypes of faecal C. jejuni, determined by serotyping with a set of 25 commercial antisera for heat-stable antigens (Penner), were Pen2 and Pen4-complex, which covered 52% of the samples. Genotyping with pulsed-field gel electrophoresis (PFGE) using SmaI restriction yielded a high diversity of C. jejuni subtypes in cattle. Determining the minimum inhibitory concentrations of ampicillin, enrofloxacin, erythromycin, gentamicin, nalidixic acid, and oxytetracycline among bovine C. jejuni isolates using a commercial broth microdilution method yielded 9% of isolates resistant to at least one of the antimicrobials examined. No multiresistant isolates were found among the bovine C. jejuni strains. The study of the shedding patterns of Campylobacter spp. among three Finnish dairy cattle herds included the examination of fresh faecal samples and tank milk samples taken five times, as well as samples from drinking troughs taken once during the one-year study. The semiquantitative enrichment method detected C. jejuni in 169 of the 340 faecal samples, mostly at low levels. In addition, C. jejuni was present in one drinking trough sample. The prevalence between herds and sampling occasions varied widely. PFGE, using SmaI as restriction enzyme, identified only a few subtypes in each herd. In two 2 of the herds, two subtypes persisted throughout the sampling. Individual animals presented various shedding patterns during the study. Comparison of C. jejuni isolates from humans, chickens and cattle included the design of primers for four new genetic markers selected from completely sequenced C. jejuni genomes 81-176, RM1221 and NCTC 11168, and the PCR examination of domestic human isolates from southern Finland in 1996, 2002 and 2003 (n=309), chicken isolates from 2003, 2006 and 2007 (n=205), and bovine isolates from 2003 (n=131). The results revealed that bovine isolates differed significantly from human and chicken isolates. In particular, the - glutamyl transpeptidase gene was uncommon among bovine isolates. The PFGE genotyping of C. jejuni isolates, using SmaI and KpnI restriction enzymes, included a geographically representative collection of isolates from domestic sporadic human infections, chicken slaughter batches, and cattle faeces and carcasses during the seasonal peak of campylobacteriosis in the summer of 2003. The study determined that 55.4% of human isolates were indistinguishable from those of chickens and cattle. Temporal association between isolates from humans and chickens was possible in 31.4% of human infections. Approximately 19% of the human infections may have been associated with cattle. However, isolates from bovine carcasses and human cases represented different PFGE subtypes. In conclusion, this study suggests that Finnish cattle is a notable reservoir of C. jejuni, the most important Campylobacter sp. in human enteric infections. Although the concentration of these organisms in bovine faeces appeared to be low, excretion can be persistent. The genetic diversity and presence or absence of marker genes support previous suggestions of host-adapted C. jejuni strains, and may indicate variations in virulence between strains from different hosts. In addition to chickens, Finnish cattle appeared to be an important reservoir and possible source of C. jejuni in domestic sporadic human infections. However, sources of campylobacters may differ between rural and urban areas in Finland, and in general, the transmission of C. jejuni of bovine origin probably occurs via other routes than food.

Identification and Epidemiological Typing of Campylobacter strains isolated from Patients in Finland

C. jejuni constitutes the majority of Campylobacter strains isolated from patients in Finland, and C. coli strains are also reported. To improve the species identification, a combination of phenotype- and genotype-based methods was applied. Standardising the cell suspension turbidity in the hippurate hydrolysis test enabled the reliable identification of hippurate-positive Campylobacter strains as C. jejuni. The detection of species-specific genes by PCR showed that about 30% of the hippurate-negative strains were C. jejuni. Three typing methods, serotyping, PCR-RFLP analysis of LOS biosynthesis genes and pulsed-field gel electrophoresis (PFGE) were evaluated as epidemiological typing tools for C. jejuni. The high number of non-typeable strains lowered the discriminatory ability of serotyping. PCR-RFLP typing offered high discrimination for both serotypeable and non-typeable strains, but the correlation between serotypes and RFLP-types was not high enough to enable its use for molecular serotyping of non-typeable strains. PFGE was a highly discriminative typing method. Although the use of two restriction enzymes generally increases the discriminatory ability, KpnI alone offered almost as high discrimination as the use of SmaI and KpnI. The characteristic seasonal distribution of Campylobacter infections with a peak in summer and low incidence in winter was mainly due to domestically acquired infections. Of the C. jejuni strains, 41% were of domestic origin compared to only 17% of the C. coli strains. Serotypes Pen 12, Pen 6,7 and Pen 27 were significantly associated with domestic C. jejuni infections, Pen 1,44, Pen 3 and Pen 37 with travel-related infections. Pen 2 and Pen 4-complex were common both in domestic and travel-related infections. Serotype Pen 2 was less common among patients 60 years or older than in younger patients, more prevalent in Western Finland than in other parts of the country and more prevalent than other serotypes in winter. The source of Pen 2 infections may be related to cattle, since Pen 2 is the most common serotype in isolates from Finnish cattle. PFGE subtypes among isolates from patients and chickens during the summer 2003 and from cattle during the whole year were compared. The analysis of indistinguishable SmaI/KpnI subtypes suggested that up to 31% of the human infections may have been mediated by chickens and 19% by cattle. Human strains isolated during two one-year sampling periods were studied by PFGE. Of the domestic strains, 69% belonged to SmaI subtypes found during both sampling periods. Four SmaI subtypes accounted for 45% of the domestic strains, further typing of these subtypes by KpnI revealed six temporally persistent SmaI/KpnI subtypes. They were only occasionally identified in travel-related strains, and therefore, can be considered to be national subtypes. Each subtype was associated with a serotype: Pen 2, Pen 12, Pen 27, Pen 4-complex, Pen 41, and Pen 57. Five of these subtypes were identified in cattle (S5/K27, S7/K1, S7/K2, S7/K5 and S64/K19), and two in chickens (S7/K1 and S64/K19) with a temporal association with human infections in 2003. Cattle are more likely potential sources of these persistent subtypes, since long-term excretion of Campylobacter strains by cattle has been reported.

Campylobacter jejuni and C.coli in Finnish poultry production

Campylobacter, mainly Campylobacter jejuni and C. coli, are worldwide recognized as a major cause of bacterial food-borne gastroenteritis (World Health Organization 2010). Epidemiological studies have shown handling or eating of poultry to be significant risk factors for human infections. Campylobacter contamination can occur at all stages of a poultry meat production cycle. In summer 1999, every broiler flock from all three major Finnish poultry slaughterhouses was studied during a five month period. Caecal samples were taken in the slaughterhouses from five birds per flock. A total of 1 132 broiler flocks were tested and 33 (2.9%) of those were Campylobacter-positive. Thirty-one isolates were identified as C. jejuni and two isolates were C. coli. The isolates were serotyped for heat-stable antigens (HS) and genotyped by pulsed-field gel electrophoresis (PFGE). The most common serotypes found were HS 6,7, 12 and 4-complex. Using a combination of SmaI and KpnI patterns, 18 different PFGE types were identified. Thirty-five Finnish C. jejuni strains with five SmaI/SacII PFGE types selected among human and chicken isolates from 1997 and 1998 were used for comparison of their PFGE patterns, amplified fragment length polymorphism (AFLP) patterns, HaeIII ribotypes, and HS serotypes. The discriminatory power of PFGE, AFLP and ribotyping with HaeIII were shown to be at the same level for this selected set of strains, and these methods assigned the strains into the same groups. The PFGE and AFLP patterns within a genotype were highly similar, indicating genetic relatedness. An HS serotype was distributed among different genotypes, and different serotypes were identified within one genotype. From one turkey parent flock, the hatchery, six different commercial turkey farms (together 12 flocks) and from 11 stages at the slaughterhouse a total of 456 samples were collected during one and the half year. For the detection of Campylobacter both conventional culture and a PCR method were used. No Campylobacter were detected in either of the samples from the turkey parent flock or from the hatchery samples using the culture method. Instead PCR detected DNA of Campylobacter in five faecal samples from the turkey parent flock and in one fluff and an eggshell sample. Six out of 12 commercial turkey flocks were found negative at the farm level but only two of those were negative at slaughter. Campylobacter-positive samples within the flock at slaughter were detected between 0% and 94%, with evisceration and chilling water being the most critical stages for contamination. All of a total of 121 Campylobacter isolates were shown to be C. jejuni using a multiplex PCR assay. PFGE analysis of all isolates with KpnI restriction enzyme resulted in 11 PFGE types (I-XI) and flaA-SVR typing yielded nine flaA-SVR alleles. Three Campylobacter-positive turkey flocks were colonized by a limited number of Campylobacter genotypes both at the farm and slaughter level.In conclusion, in our first study in 1999 a low prevalence of Campylobacter in Finnish broiler flocks was detected and it has remained at a low level during the study period until the present. In the turkey meat production, we found that flocks which were negative at the farm became contaminated with Campylobacter at the slaughter process. These results suggest that proper and efficient cleaning and disinfection of slaughter and processing premises are needed to avoid cross-contamination. Prevention of colonization at the farm by a high level of biosecurity control and hygiene may be one of the most efficient ways to reduce the amount of Campylobacter-positive poultry meat in Finland. In Finland, with a persistent low level of Campylobacter-positive flocks, it could be speculated that the use of logistic slaughtering, according to Campylobacter status at farm, might have be advantageous in reducing Campylobacter contamination of retail poultry products. However, the significance of the domestic poultry meat for human campylobacteriosis in Finland should be evaluated.