Process Analytical Technology Approach on Fluid Bed Granulation and Drying : Identifying Critical Relationships and Constructing the Design Space

Fluid bed granulation is a key pharmaceutical process which improves many of the powder properties for tablet compression. Dry mixing, wetting and drying phases are included in the fluid bed granulation process. Granules of high quality can be obtained by understanding and controlling the critical process parameters by timely measurements. Physical process measurements and particle size data of a fluid bed granulator that are analysed in an integrated manner are included in process analytical technologies (PAT). Recent regulatory guidelines strongly encourage the pharmaceutical industry to apply scientific and risk management approaches to the development of a product and its manufacturing process. The aim of this study was to utilise PAT tools to increase the process understanding of fluid bed granulation and drying. Inlet air humidity levels and granulation liquid feed affect powder moisture during fluid bed granulation. Moisture influences on many process, granule and tablet qualities. The approach in this thesis was to identify sources of variation that are mainly related to moisture. The aim was to determine correlations and relationships, and utilise the PAT and design space concepts for the fluid bed granulation and drying. Monitoring the material behaviour in a fluidised bed has traditionally relied on the observational ability and experience of an operator. There has been a lack of good criteria for characterising material behaviour during spraying and drying phases, even though the entire performance of a process and end product quality are dependent on it. The granules were produced in an instrumented bench-scale Glatt WSG5 fluid bed granulator. The effect of inlet air humidity and granulation liquid feed on the temperature measurements at different locations of a fluid bed granulator system were determined. This revealed dynamic changes in the measurements and enabled finding the most optimal sites for process control. The moisture originating from the granulation liquid and inlet air affected the temperature of the mass and pressure difference over granules. Moreover, the effects of inlet air humidity and granulation liquid feed rate on granule size were evaluated and compensatory techniques used to optimize particle size. Various end-point indication techniques of drying were compared. The ∆T method, which is based on thermodynamic principles, eliminated the effects of humidity variations and resulted in the most precise estimation of the drying end-point. The influence of fluidisation behaviour on drying end-point detection was determined. The feasibility of the ∆T method and thus the similarities of end-point moisture contents were found to be dependent on the variation in fluidisation between manufacturing batches. A novel parameter that describes behaviour of material in a fluid bed was developed. Flow rate of the process air and turbine fan speed were used to calculate this parameter and it was compared to the fluidisation behaviour and the particle size results. The design space process trajectories for smooth fluidisation based on the fluidisation parameters were determined. With this design space it is possible to avoid excessive fluidisation and improper fluidisation and bed collapse. Furthermore, various process phenomena and failure modes were observed with the in-line particle size analyser. Both rapid increase and a decrease in granule size could be monitored in a timely manner. The fluidisation parameter and the pressure difference over filters were also discovered to express particle size when the granules had been formed. The various physical parameters evaluated in this thesis give valuable information of fluid bed process performance and increase the process understanding.

Towards real-time understanding of processes in pharmaceutical powder technology

There is a need for better understanding of the processes and new ideas to develop traditional pharmaceutical powder manufacturing procedures. Process analytical technology (PAT) has been developed to improve understanding of the processes and establish methods to monitor and control processes. The interest is in maintaining and even improving the whole manufacturing process and the final products at real-time. Process understanding can be a foundation for innovation and continuous improvement in pharmaceutical development and manufacturing. New methods are craved for to increase the quality and safety of the final products faster and more efficiently than ever before. The real-time process monitoring demands tools, which enable fast and noninvasive measurements with sufficient accuracy. Traditional quality control methods have been laborious and time consuming and they are performed off line i.e. the analysis has been removed from process area. Vibrational spectroscopic methods are responding this challenge and their utilisation have increased a lot during the past few years. In addition, other methods such as colour analysis can be utilised in noninvasive real-time process monitoring. In this study three pharmaceutical processes were investigated: drying, mixing and tabletting. In addition tablet properties were evaluated. Real-time monitoring was performed with NIR and Raman spectroscopies, colour analysis, particle size analysis and compression data during tabletting was evaluated using mathematical modelling. These methods were suitable for real-time monitoring of pharmaceutical unit operations and increase the knowledge of the critical parameters in the processes and the phenomena occurring during operations. They can improve our process understanding and therefore, finally, enhance the quality of final products.

How to design educational settings to promote collaborative inquiry: Pedagogical infrastructures for technology-enhanced progressive inquiry

Strategies of scientific, question-driven inquiry are stated to be important cultural practices that should be educated in schools and universities. The present study focuses on investigating multiple efforts to implement a model of Progressive Inquiry and related Web-based tools in primary, secondary and university level education, to develop guidelines for educators in promoting students collaborative inquiry practices with technology. The research consists of four studies. In Study I, the aims were to investigate how a human tutor contributed to the university students collaborative inquiry process through virtual forums, and how the influence of the tutoring activities is demonstrated in the students inquiry discourse. Study II examined an effort to implement technology-enhanced progressive inquiry as a distance working project in a middle school context. Study III examined multiple teachers' methods of organizing progressive inquiry projects in primary and secondary classrooms through a generic analysis framework. In Study IV, a design-based research effort consisting of four consecutive university courses, applying progressive inquiry pedagogy, was retrospectively re-analyzed in order to develop the generic design framework. The results indicate that appropriate teacher support for students collaborative inquiry efforts appears to include interplay between spontaneity and structure. Careful consideration should be given to content mastery, critical working strategies or essential knowledge practices that the inquiry approach is intended to promote. In particular, those elements in students activities should be structured and directed, which are central to the aim of Progressive Inquiry, but which the students do not recognize or demonstrate spontaneously, and which are usually not taken into account in existing pedagogical methods or educational conventions. Such elements are, e.g., productive co-construction activities; sustained engagement in improving produced ideas and explanations; critical reflection of the adopted inquiry practices, and sophisticated use of modern technology for knowledge work. Concerning the scaling-up of inquiry pedagogy, it was concluded that one individual teacher can also apply the principles of Progressive Inquiry in his or her own teaching in many innovative ways, even under various institutional constraints. The developed Pedagogical Infrastructure Framework enabled recognizing and examining some central features and their interplay in the designs of examined inquiry units. The framework may help to recognize and critically evaluate the invisible learning-cultural conventions in various educational settings and can mediate discussions about how to overcome or change them.

Mu in vitro Transposition Technology in Functional Genetics and Genomics: Applications on Mouse and Bacteriophages

Transposons are mobile elements of genetic material that are able to move in the genomes of their host organisms using a special form of recombination called transposition. Bacteriophage Mu was the first transposon for which a cell-free in vitro transposition reaction was developed. Subsequently, the reaction has been refined and the minimal Mu in vitro reaction is useful in the generation of comprehensive libraries of mutant DNA molecules that can be used in a variety of applications. To date, the functional genetics applications of Mu in vitro technology have been subjected to either plasmids or genomic regions and entire genomes of viruses cloned on specific vectors. This study expands the use of Mu in vitro transposition in functional genetics and genomics by describing novel methods applicable to the targeted transgenesis of mouse and the whole-genome analysis of bacteriophages. The methods described here are rapid, efficient, and easily applicable to a wide variety of organisms, demonstrating the potential of the Mu transposition technology in the functional analysis of genes and genomes. First, an easy-to-use, rapid strategy to generate construct for the targeted mutagenesis of mouse genes was developed. To test the strategy, a gene encoding a neuronal K+/Cl- cotransporter was mutagenised. After a highly efficient transpositional mutagenesis, the gene fragments mutagenised were cloned into a vector backbone and transferred into bacterial cells. These constructs were screened with PCR using an effective 3D matrix system. In addition to traditional knock-out constructs, the method developed yields hypomorphic alleles that lead into reduced expression of the target gene in transgenic mice and have since been used in a follow-up study. Moreover, a scheme is devised to rapidly produce conditional alleles from the constructs produced. Next, an efficient strategy for the whole-genome analysis of bacteriophages was developed based on the transpositional mutagenesis of uncloned, infective virus genomes and their subsequent transfer into susceptible host cells. Mutant viruses able to produce viable progeny were collected and their transposon integration sites determined to map genomic regions nonessential to the viral life cycle. This method, applied here to three very different bacteriophages, PRD1, ΦYeO3 12, and PM2, does not require the target genome to be cloned and is directly applicable to all DNA and RNA viruses that have infective genomes. The method developed yielded valuable novel information on the three bacteriophages studied and whole-genome data can be complemented with concomitant studies on individual genes. Moreover, end-modified transposons constructed for this study can be used to manipulate genomes devoid of suitable restriction sites.

Analyzing changes in macro-level drivers of country-specific emissions : The role of consumption, technology and trade

Industrial ecology is an important field of sustainability science. It can be applied to study environmental problems in a policy relevant manner. Industrial ecology uses ecosystem analogy; it aims at closing the loop of materials and substances and at the same time reducing resource consumption and environmental emissions. Emissions from human activities are related to human interference in material cycles. Carbon (C), nitrogen (N) and phosphorus (P) are essential elements for all living organisms, but in excess have negative environmental impacts, such as climate change (CO2, CH4 N2O), acidification (NOx) and eutrophication (N, P). Several indirect macro-level drivers affect emissions change. Population and affluence (GDP/capita) often act as upward drivers for emissions. Technology, as emissions per service used, and consumption, as economic intensity of use, may act as drivers resulting in a reduction in emissions. In addition, the development of country-specific emissions is affected by international trade. The aim of this study was to analyse changes in emissions as affected by macro-level drivers in different European case studies. ImPACT decomposition analysis (IPAT identity) was applied as a method in papers I III. The macro-level perspective was applied to evaluate CO2 emission reduction targets (paper II) and the sharing of greenhouse gas emission reduction targets (paper IV) in the European Union (EU27) up to the year 2020. Data for the study were mainly gathered from official statistics. In all cases, the results were discussed from an environmental policy perspective. The development of nitrogen oxide (NOx) emissions was analysed in the Finnish energy sector during a long time period, 1950 2003 (paper I). Finnish emissions of NOx began to decrease in the 1980s as the progress in technology in terms of NOx/energy curbed the impact of the growth in affluence and population. Carbon dioxide (CO2) emissions related to energy use during 1993 2004 (paper II) were analysed by country and region within the European Union. Considering energy-based CO2 emissions in the European Union, dematerialization and decarbonisation did occur, but not sufficiently to offset population growth and the rapidly increasing affluence during 1993 2004. The development of nitrogen and phosphorus load from aquaculture in relation to salmonid consumption in Finland during 1980 2007 was examined, including international trade in the analysis (paper III). A regional environmental issue, eutrophication of the Baltic Sea, and a marginal, yet locally important source of nutrients was used as a case. Nutrient emissions from Finnish aquaculture decreased from the 1990s onwards: although population, affluence and salmonid consumption steadily increased, aquaculture technology improved and the relative share of imported salmonids increased. According to the sustainability challenge in industrial ecology, the environmental impact of the growing population size and affluence should be compensated by improvements in technology (emissions/service used) and with dematerialisation. In the studied cases, the emission intensity of energy production could be lowered for NOx by cleaning the exhaust gases. Reorganization of the structure of energy production as well as technological innovations will be essential in lowering the emissions of both CO2 and NOx. Regarding the intensity of energy use, making the combustion of fuels more efficient and reducing energy use are essential. In reducing nutrient emissions from Finnish aquaculture to the Baltic Sea (paper III) through technology, limits of biological and physical properties of cultured fish, among others, will eventually be faced. Regarding consumption, salmonids are preferred to many other protein sources. Regarding trade, increasing the proportion of imports will outsource the impacts. Besides improving technology and dematerialization, other viewpoints may also be needed. Reducing the total amount of nutrients cycling in energy systems and eventually contributing to NOx emissions needs to be emphasized. Considering aquaculture emissions, nutrient cycles can be partly closed through using local fish as feed replacing imported feed. In particular, the reduction of CO2 emissions in the future is a very challenging task when considering the necessary rates of dematerialisation and decarbonisation (paper II). Climate change mitigation may have to focus on other greenhouse gases than CO2 and on the potential role of biomass as a carbon sink, among others. The global population is growing and scaling up the environmental impact. Population issues and growing affluence must be considered when discussing emission reductions. Climate policy has only very recently had an influence on emissions, and strong actions are now called for climate change mitigation. Environmental policies in general must cover all the regions related to production and impacts in order to avoid outsourcing of emissions and leakage effects. The macro-level drivers affecting changes in emissions can be identified with the ImPACT framework. Statistics for generally known macro-indicators are currently relatively well available for different countries, and the method is transparent. In the papers included in this study, a similar method was successfully applied in different types of case studies. Using transparent macro-level figures and a simple top-down approach are also appropriate in evaluating and setting international emission reduction targets, as demonstrated in papers II and IV. The projected rates of population and affluence growth are especially worth consideration in setting targets. However, sensitivities in calculations must be carefully acknowledged. In the basic form of the ImPACT model, the economic intensity of consumption and emission intensity of use are included. In seeking to examine consumption but also international trade in more detail, imports were included in paper III. This example demonstrates well how outsourcing of production influences domestic emissions. Country-specific production-based emissions have often been used in similar decomposition analyses. Nevertheless, trade-related issues must not be ignored.

Information Technology in Construction – Domain Definition and Research Issues

This article discusses the scope of research on the application of information technology in construction (ITC). A model of the information and material activities which together constitute the construction process is presented, using the IDEF0 activity modelling methodology. Information technology is defined to include all kinds of technology used for the storage, transfer and manipulation of information, thus also including devices such as copying machines, faxes and mobile phones. Using the model the domain of ITC research is defined as the use of information technology to facilitate and re-engineer the information process component of construction. Developments during the last decades in IT use in construction is discussed against a background of a simplified model of generic information processing tasks. The scope of ITC is compared with the scopes of research in related areas such as design methodology, construction management and facilities management. Health care is proposed as an interesting alternative (to the often used car manufacturing industry), as an IT application domain to compare with. Some of the key areas of ITC research in recent years; expert systems, company IT strategies, and product modelling are shortly discussed. The article finishes with a short discussion of the problems of applying standard scientific methodology in ITC research, in particular in product model research.

The Electronic Journal of Information Technology in Construction (ITcon): An Open Access Journal Using an Un-paid, Volunteer-Based Organization

Introduction This case study is based on the experiences with the Electronic Journal of Information Technology in Construction (ITcon), founded in 1995. Development This journal is an example of a particular category of open access journals, which use neither author charges nor subscriptions to finance their operations, but rely largely on unpaid voluntary work in the spirit of the open source movement. The journal has, after some initial struggle, survived its first decade and is now established as one of half-a-dozen peer reviewed journals in its field. Operations The journal publishes articles as they become ready, but creates virtual issues through alerting messages to “subscribers”. It has also started to publish special issues, since this helps in attracting submissions, and also helps in sharing the work-load of review management. From the start the journal adopted a rather traditional layout of the articles. After the first few years the HTML version was dropped and papers are only published in PDF format. Performance The journal has recently been benchmarked against the competing journals in its field. Its acceptance rate of 53% is slightly higher and its average turnaround time of seven months almost a year faster compared to those journals in the sample for which data could be obtained. The server log files for the past three years have also been studied. Conclusions Our overall experience demonstrates that it is possible to publish this type of OA journal, with a yearly publishing volume equal to a quarterly journal and involving the processing of some fifty submissions a year, using a networked volunteer-based organization.

Essays on Platforms: Business Strategies, Regulation and Policy in Telecommunications, Media and Technology Industries

The growth of the information economy has been stellar in the last decade. General-purpose technologies such as the computer and the Internet have promoted productivity growth in a large number of industries. The effect on telecommunications, media and technology industries has been particularly strong. These industries include mobile telecommunications, printing and publishing, broadcasting, software, hardware and Internet services. There have been large structural changes, which have led to new questions on business strategies, regulation and policy. This thesis focuses on four such questions and answers them by extending the theoretical literature on platforms. The questions (with short answers) are: (i) Do we need to regulate how Internet service providers discriminate between content providers? (Yes.) (ii) What are the welfare effects of allowing consumers to pay to remove advertisements from advertisement-supported products?(Ambiguous, but those watching ads are worse off.) (iii) Why are some markets characterized by open platforms, extendable by third parties, and some by closed platforms, which are not extendable? (It is a trade-off between intensified competition for consumers and benefits from third parties) (iv) Do private platform providers allow third parties to access their platform when it is socially desirable? (No.)

Technology-related peso problems in stock returns

Although empirical evidence suggests the contrary, many asset pricing models assume stock returns to be symmetrically distributed. In this paper it is argued that the occurrence of negative jumps in a firm's future earnings and, consequently, in its stock price, is positively related to the level of network externalities in the firm's product market. If the ex post frequency of these negative jumps in a sample does not equal the ex ante assessed probability of occurrence, the sample is subject to a peso problem. The hypothesis is tested for by regressing the skewness coefficient of a firm’s realised stock return distribution on the firm’s R&D intensity, i.e. the ratio of the firm’s research and development expenditure to its net sales. The empirical results support the technology-related peso problem hypothesis. In samples subject to such a peso problem, the returns are biased up and the variance is biased down.

What is A Virtual Service?- Broadening the Perspective on Technology-Based Services

This article expands the discussion of the impact of technology on services and contributes to a broader comprehension of the nature of virtual services. This is done by discovering dimensions that distinguish physical services from virtual services, i.e. services that are distributed by electronic means and where the customer has no direct human interaction with the service provider. Differences in the core characteristics of services, servicescape and service delivery are discussed. Moreover, dimensions that differentiate between virtual services are analysed. A classification scheme for virtual services is proposed, including the origin of the service, the element of the service offering, the customisation process, stage of the service process performed, and the degree of mobility of the service.