Microbial quality of hemp (Cannabis sativa L.) and flax (Linum usitatissimum L.) from plants to thermal insulation

Flax and hemp have traditionally been used mainly for textiles, but recently interest has also been focused on non-textile applications. Microbial quality throughout the whole processing chain of bast fibres has not previously been studied. This study concentrates on the microbial quality and possible microbial risks in the production chain of hemp and flax fibres and fibrous thermal insulations. In order to be able to utilize hemp and flax fibres, the bast fibres must be separated from the rest of the plant. Non-cellulosic components can be removed with various pretreatment processes, which are associated with a certain risk of microbial contamination. In this study enzymatic retting and steam explosion (STEX) were examined as pretreatment processes. On the basis of the results obtained in this study, the microbial contents on stalks of both plants studied increased at the end of the growing season and during the winter. However, by processing and mechanical separation it is possible to produce fibres containing less moulds and bacteria than the whole stem. Enzymatic treatment encouraged the growth of moulds in fibres. Steam explosion reduced the amount of moulds in fibres. Dry thermal treatment used in this study did not markedly reduce the amount of microbes. In this project an emission measurement chamber was developed which was suitable for measurements of emissions from both mat type and loose fill type insulations, and capable of interdisciplinary sampling. In this study, the highest amounts of fungal emissions were in the range of 10^3 10^5 cfu/m^3 from the flax and hemp insulations at 90% RH of air. The fungal emissions from stone wool, glass wool and recycled paper insulations were below 10^2 cfu/m^3 even at 90% RH. Equally low values were obtained from bast fibrous materials in lower humidities (at 30% and 80% RH of air). After drying of moulded insulations at 30% RH, the amounts of emitted moulds were in all cases higher compared to the emissions at 90% RH before drying. The most common fungi in bast fibres were Penicillium and Rhizopus. The widest variety of different fungi was in the untreated hemp and linseed fibres and in the commercial loose-fill flax insulation. Penicillium, Rhizopus and Paecilomyces were the most tolerant to steam explosion. According to the literature, the most common fungi in building materials and indoor air are Penicillium, Aspergillus and Cladosporium, which were all found in some of the bast fibre materials in this study. As organic materials, hemp and flax fibres contain high levels of nutrients for microbial growth. The amount of microbes can be controlled and somewhat decreased by the processing methods presented.

Role of heat treatment in the processing and quality of oat flakes

This thesis reports on investigations into the influence of heat treatment on the manufacturing of oat flakes. Sources of variation in the oat flake quality are reviewed, including the whole chain from the farm to the consumer. The most important quality parameters of oat flakes are the absence of lipid hydrolysing enzymes, specific weight, thickness, breakage (fines), water absorption. Flavour, colour and pasting properties are also important, but were not included in the experimental part of this study. Of particular interest was the role of heat processing. The first possible heat treatment may occur already during grain drying, which in Finland generally happens at the farm. At the mill, oats are often kilned to stabilise the product by inactivating lipid hydrolysing enzymes. Almost invariably steaming is used during flaking, to soften the groats and reduce flake breakage. This thesis presents the use of a material science approach to investigating a complex system, typical of food processes. A combination of fundamental and empirical rheological measurements was used together with a laboratory scale process to simulate industrial processing. The results were verified by means of industrial trials. Industrially produced flakes at three thickness levels (nominally 0.75, 0.85 and 0.90 mm) were produced from kilned and unkilned oat groats, and the flake strength was measured at different moisture contents. Kilning was not found to significantly affect the force required to puncture a flake with a 2mm cylindrical probe, which was taken as a measure of flake strength. To further investigate how heat processing contributes to flake quality, dynamic mechanical analysis was used to characterise the effect of heat on the mechanical properties of oats. A marked stiffening of the groat, of up to about 50% increase in storage modulus, was observed during first heating at around 36 to 57°C. This was also observed in tablets prepared from ground groats and extracted oat starch. This stiffening was thus attributed to increased adhesion between starch granules. Groats were steamed in a laboratory steamer and were tempered in an oven at 80 110°C for 30 90 min. The maximum force required to compress the steamed groats to 50% strain increased from 50.7 N to 57.5 N as the tempering temperature was increased from 80 to 110°C. Tempering conditions also affected water absorption. A significantly higher moisture content was observed for kilned (18.9%) compared to unkilned (17.1%) groats, but otherwise had no effect on groat height, maximum force or final force after a 5 s relaxation time. Flakes were produced from the tempered groats using a laboratory flaking machine, using a roll gap of 0.4 mm. Apart from specific weight, flake properties were not influenced by kilning. Tempering conditions however had significant effects on the specific weight, thickness and water absorption of the flakes, as well as on the amount of fine material (<2 mm) produced during flaking. Flake strength correlated significantly with groat strength and flake thickness. Trial flaking at a commercial mill confirmed that groat temperature after tempering influenced water absorption. Variation in flake strength was observed , but at the groat temperatures required to inactivate lipase, it was rather small. Cold flaking of groats resulted in soft, floury flakes. The results presented in this thesis suggest that heating increased the adhesion between starch granules. This resulted in an increase in the stiffness and brittleness of the groat. Brittle fracture, rather than plastic flow, during flaking could result in flaws and cracks in the flake. These would be expected to increase water absorption. This was indeed observed as tempering temperature increased. Industrial trials, conducted with different groat temperatures, confirmed the main findings of the laboratory experiments. The approach used in the present study allowed the systematic study of the effect of interacting process parameters on product quality. There have been few scientific studies of oat processing, and these results can be used to understand the complex effects of process variables on flake quality. They also offer an insight into what happens as the oat groat is deformed into a flake.

Information, risk and trust in the food chain : Ex-ante valuation of consumer willingness to pay for beef quality information using the contingent valuation method

The safety of food has become an increasingly interesting issue to consumers and the media. It has also become a source of concern, as the amount of information on the risks related to food safety continues to expand. Today, risk and safety are permanent elements within the concept of food quality. Safety, in particular, is the attribute that consumers find very difficult to assess. The literature in this study consists of three main themes: traceability; consumer behaviour related to both quality and safety issues and perception of risk; and valuation methods. The empirical scope of the study was restricted to beef, because the beef labelling system enables reliable tracing of the origin of beef, as well as attributes related to safety, environmental friendliness and animal welfare. The purpose of this study was to examine what kind of information flows are required to ensure quality and safety in the food chain for beef, and who should produce that information. Studying the willingness to pay of consumers makes it possible to determine whether the consumers consider the quantity of information available on the safety and quality of beef sufficient. One of the main findings of this study was that the majority of Finnish consumers (73%) regard increased quality information as beneficial. These benefits were assessed using the contingent valuation method. The results showed that those who were willing to pay for increased information on the quality and safety of beef would accept an average price increase of 24% per kilogram. The results showed that certain risk factors impact consumer willingness to pay. If the respondents considered genetic modification of food or foodborne zoonotic diseases as harmful or extremely harmful risk factors in food, they were more likely to be willing to pay for quality information. The results produced by the models thus confirmed the premise that certain food-related risks affect willingness to pay for beef quality information. The results also showed that safety-related quality cues are significant to the consumers. In the first place, the consumers would like to receive information on the control of zoonotic diseases that are contagious to humans. Similarly, other process-control related information ranked high among the top responses. Information on any potential genetic modification was also considered important, even though genetic modification was not regarded as a high risk factor.

A dynamic programming model for optimising feeding and slaughter decisions regarding fattening pigs

Costs of purchasing new piglets and of feeding them until slaughter are the main variable expenditures in pig fattening. They both depend on slaughter intensity, the nature of feeding patterns and the technological constraints of pig fattening, such as genotype. Therefore, it is of interest to examine the effect of production technology and changes in input and output prices on feeding and slaughter decisions. This study examines the problem by using a dynamic programming model that links genetic characteristics of a pig to feeding decisions and the timing of slaughter and takes into account how these jointly affect the quality-adjusted value of a carcass. The model simulates the growth mechanism of a pig under optional feeding and slaughter patterns and then solves the optimal feeding and slaughter decisions recursively. The state of nature and the genotype of a pig are known in the analysis. The main contribution of this study is the dynamic approach that explicitly takes into account carcass quality while simultaneously optimising feeding and slaughter decisions. The method maximises the internal rate of return to the capacity unit. Hence, the results can have vital impact on competitiveness of pig production, which is known to be quite capital-intensive. The results suggest that producer can significantly benefit from improvements in the pig's genotype, because they improve efficiency of pig production. The annual benefits from obtaining pigs of improved genotype can be more than €20 per capacity unit. The annual net benefits of animal breeding to pig farms can also be considerable. Animals of improved genotype can reach optimal slaughter maturity quicker and produce leaner meat than animals of poor genotype. In order to fully utilise the benefits of animal breeding, the producer must adjust feeding and slaughter patterns on the basis of genotype. The results suggest that the producer can benefit from flexible feeding technology. The flexible feeding technology segregates pigs into groups according to their weight, carcass leanness, genotype and sex and thereafter optimises feeding and slaughter decisions separately for these groups. Typically, such a technology provides incentives to feed piglets with protein-rich feed such that the genetic potential to produce leaner meat is fully utilised. When the pig approaches slaughter maturity, the share of protein-rich feed in the diet gradually decreases and the amount of energy-rich feed increases. Generally, the optimal slaughter weight is within the weight range that pays the highest price per kilogram of pig meat. The optimal feeding pattern and the optimal timing of slaughter depend on price ratios. Particularly, an increase in the price of pig meat provides incentives to increase the growth rates up to the pig's biological maximum by increasing the amount of energy in the feed. Price changes and changes in slaughter premium can also have large income effects. Key words: barley, carcass composition, dynamic programming, feeding, genotypes, lean, pig fattening, precision agriculture, productivity, slaughter weight, soybeans

Essays on socially optimal phosphorus policies in crop production

Phosphorus is a nutrient needed in crop production. While boosting crop yields it may also accelerate eutrophication in the surface waters receiving the phosphorus runoff. The privately optimal level of phosphorus use is determined by the input and output prices, and the crop response to phosphorus. Socially optimal use also takes into account the impact of phosphorus runoff on water quality. Increased eutrophication decreases the economic value of surface waters by Deteriorating fish stocks, curtailing the potential for recreational activities and by increasing the probabilities of mass algae blooms. In this dissertation, the optimal use of phosphorus is modelled as a dynamic optimization problem. The potentially plant available phosphorus accumulated in soil is treated as a dynamic state variable, the control variable being the annual phosphorus fertilization. For crop response to phosphorus, the state variable is more important than the annual fertilization. The level of this state variable is also a key determinant of the runoff of dissolved, reactive phosphorus. Also the loss of particulate phosphorus due to erosion is considered in the thesis, as well as its mitigation by constructing vegetative buffers. The dynamic model is applied for crop production on clay soils. At the steady state, the analysis focuses on the effects of prices, damage parameterization, discount rate and soil phosphorus carryover capacity on optimal steady state phosphorus use. The economic instruments needed to sustain the social optimum are also analyzed. According to the results the economic incentives should be conditioned on soil phosphorus values directly, rather than on annual phosphorus applications. The results also emphasize the substantial effects the differences in varying discount rates of the farmer and the social planner have on optimal instruments. The thesis analyzes the optimal soil phosphorus paths from its alternative initial levels. It also examines how erosion susceptibility of a parcel affects these optimal paths. The results underline the significance of the prevailing soil phosphorus status on optimal fertilization levels. With very high initial soil phosphorus levels, both the privately and socially optimal phosphorus application levels are close to zero as the state variable is driven towards its steady state. The soil phosphorus processes are slow. Therefore, depleting high phosphorus soils may take decades. The thesis also presents a methodologically interesting phenomenon in problems of maximizing the flow of discounted payoffs. When both the benefits and damages are related to the same state variable, the steady state solution may have an interesting property, under very general conditions: The tail of the payoffs of the privately optimal path as well as the steady state may provide a higher social welfare than the respective tail of the socially optimal path. The result is formalized and an applied to the created framework of optimal phosphorus use.

Liikennepolttoaineeksi tarkoitettu ohraetanoli, Suomen ohramarkkinat ja ilmastonmuutos

The aim of the thesis was to analyze the use of barley as an input for bioethanol production and the impacts the use has on the Finnish barley markets. Two main research questions were formulated. First, privately and socially optimal bioethanol production levels were examined. In the social optimum, the climate benefits of bioethanol production were considered. It was calculated that the production and use of bioethanol created smaller CO2 -emissions when compared with the production and use of gasoline. Second, the impacts of bioethanol production on farmland allocation and agricultural production were analyzed. In more detail, the second aim was to analyze the farmland allocation between wheat and barley cultivation and green set aside in the private and social optimum. An analytical model was produced to analyze the barley markets in Finland. To provide an empirical counterpart to this model, existing research data on bioethanol production and barley cultivation was used. The aim of the model was to analyze the supply and the demand as well as market equilibrium of barley. Furthermore, the model provided a framework for analyzing the differences between the private optimum and social optimum of bioethanol production in Finland. The demand for barley consists of animal feed demand and bioethanol demand. On the supply side, a heterogeneous model of farmland quality was used. With this framework, it is possible to analyze farmland allocation between barley and wheat cultivation and green set aside and how the climate benefits of bioethanol production affects the allocation. Moreover, the relative changes in barley price between the private and social optimum were analyzed. Based on the empirical analysis, the private optimum for barley based bioethanol production is 58 691 metric tons. However, the social optimum for barley based bioethanol production is 72 736 metric tons. The portion of farmland that is allocated to barley cultivation is increased if the climate benefits of bioethanol production are considered. In the private optimum, 1/19 of the total farmland is allocated to barley cultivation whereas in social optimum the share increases to 7/19. Furthermore, the increase in barley price between private and social optimum is rather modest. Total increase in price is only about 1,8 percent.

Quality of ALICE SSD modules revealed by electrical tests

ALICE (A Large Ion Collider Experiment) is an experiment at CERN (European Organization for Nuclear Research), where a heavy-ion detector is dedicated to exploit the unique physics potential of nucleus-nucleus interactions at LHC (Large Hadron Collider) energies. In a part of that project, 716 so-called type V4 modules were assembles in Detector Laboratory of Helsinki Institute of Physics during the years 2004 - 2006. Altogether over a million detector strips has made this project the most massive particle detector project in the science history of Finland. One ALICE SSD module consists of a double-sided silicon sensor, two hybrids containing 12 HAL25 front end readout chips and some passive components, such has resistors and capacitors. The components are connected together by TAB (Tape Automated Bonding) microcables. The components of the modules were tested in every assembly phase with comparable electrical tests to ensure the reliable functioning of the detectors and to plot the possible problems. The components were accepted or rejected by the limits confirmed by ALICE collaboration. This study is concentrating on the test results of framed chips, hybrids and modules. The total yield of the framed chips is 90.8%, hybrids 96.1% and modules 86.2%. The individual test results have been investigated in the light of the known error sources that appeared during the project. After solving the problems appearing during the learning-curve of the project, the material problems, such as defected chip cables and sensors, seemed to induce the most of the assembly rejections. The problems were typically seen in tests as too many individual channel failures. Instead, the bonding failures rarely caused the rejections of any component. One sensor type among three different sensor manufacturers has proven to have lower quality than the others. The sensors of this manufacturer are very noisy and their depletion voltage are usually outside of the specification given to the manufacturers. Reaching 95% assembling yield during the module production demonstrates that the assembly process has been highly successful.

Measuring and tracking quality factors in Free and Open Source Software projects

Free and Open Source Software (FOSS) has gained increased interest in the computer software industry, but assessing its quality remains a challenge. FOSS development is frequently carried out by globally distributed development teams, and all stages of development are publicly visible. Several product and process-level quality factors can be measured using the public data. This thesis presents a theoretical background for software quality and metrics and their application in a FOSS environment. Information available from FOSS projects in three information spaces are presented, and a quality model suitable for use in a FOSS context is constructed. The model includes both process and product quality metrics, and takes into account the tools and working methods commonly used in FOSS projects. A subset of the constructed quality model is applied to three FOSS projects, highlighting both theoretical and practical concerns in implementing automatic metric collection and analysis. The experiment shows that useful quality information can be extracted from the vast amount of data available. In particular, projects vary in their growth rate, complexity, modularity and team structure.

The Structure and Short-Term Development of Finnish Industries in the 1920s and 1930s : An Input-output Approach

Tutkimuksen tavoitteena on tuottaa uutta tietoa Suomen kansantalouden rakenteesta ja lyhyen aikavälin kehityksestä 1920- ja 1930-luvulla. Tutkimus toteutettiin laatimalla kansantaloutta kuvaava panos-tuotostaulu vuodelle 1928 sekä sen laajennus, panos-tuotosmalli. Aineiston avulla kuvataan kansantalouden rakenteellisia riippuvuuksia, tuotannon avaintoimialoja sekä näiden vaikutusta kansantalouteen. Lisäksi tutkimuksessa tarkastellaan kansantalouden tuontiriippuvuutta sekä tuontitullien vaikutusta hintoihin 1930-luvun laman aikana. Tutkimuksen perusteella voitiin identifioida Suomen kansantalouden avaintoimialat vuonna 1928: maatalous, metsätalous, elintarviketeollisuus, puuteollisuus, paperiteollisuus ja rakennustoiminta. Erityisesti elintarviketeollisuuden vahva rooli kansantaloudessa oli kenties yllättävää, erityisesti kun huomioidaan kuinka vähän toimiala on saanut huomiota osakseen taloushistorian tutkimuksessa. Tutkimus osoitti, että Suomen vienti oli pääomavaltaisempaa kuin tuonti. Vaikka tämän tuloksen tulkinta on varauksellinen, tutkimus pystyi osoittamaan ja kvantifioimaan toimialojen työ- ja pääomapanoksen osuuden tuotoksesta yksityiskohtaisesti. Panos-tuotosmallilla arvioitiin puuteollisuuden, paperiteollisuuden ja rakennustoiminnan ajanjaksona 1928-32 tapahtuneen loppukäytön muutoksen vaikutusta kansantalouteen. Merkittävä havainto on, että rakennustoiminnan loppukäytön muutoksella oli erittäin suuri kasvua vähentävä vaikutus koko kansantaloudessa. Talonrakennusinvestointien romahtaminen aiheutti lähes 13 prosentin tuotannon laskun kansantaloudessa. Vaikutus oli jopa suurempi kuin puuteollisuuden viennin romahtamisen. Tulokset osoittavat toisaalta, että yksityisen kulutuksen merkitys kansantaloudelle oli erittäin vahva. Esimerkiksi puuteollisuuden viennin romahtaminen aiheutti yli 4 % tuotannon vähenemisen mutta huomioitaessa mallissa myös yksityisen kulutuksen väheneminen, oli kokonaisvaikutus yli 10 %. Yksityisen kulutuksen huomioiminen mallissa siis yli kaksinkertaisti toimialojen vaikutukset kansantalouteen. Tulokset vahvistivat aiemmissa tutkimuksissa esitettyjä johtopäätöksiä tullipolitiikasta ja osoittivat maatalouteen läheisesti liittyvän elintarviketeollisuuden olleen eniten suojeltu toimiala kansantaloudessa. Muut kotimarkkinoiden toimialat eivät kuitenkaan hyötyneet tullipolitiikasta lamakauden aikana. Panos-tuotoshintamallilla osoitettiin, ettei tullipolitiikka ollut niin onnistunutta kuin aikalaistutkimuksissa väitettiin, vaan tullit korkeintaan pystyivät hidastamaan hintojen alenemista. Tutkimuksen liitteenä esitetään kaikki keskeiset Suomen kansantaloutta vuonna 1928 kuvaavat tilastolliset taulukot, mukaan lukien käyttö- ja tarjontataulukot, panos-tuotostaulukot, panoskertoimet, Leontiefin käänteismatriisi sekä työ- ja pääomapanoskertoimet.