Trapping phosphorus (III) into polyoxometalates: synthesis, characterisation and electronic behaviour study

The introduction of electronically-active heteroanions into polyoxometalates (POMs) is one of the emerging topics in this field. The novel clusters have shown unprecedented intramolecular electron-transfer features that can be directly mediated by the incorporated heteroanions. In this thesis, we will focus on the study of phosphite (HPO32-) as new non-traditional heteroanions, discover HPO32- templated nanostructures, investigate their electronic behaviours as well as understand the self-assembly process of HPO32--templated species. The thesis starts with incorporating HPO32- into POM cages. The feasibility of this work was illustrated by the successful trapping of HPO32- into a “Trojan Horse” type {W18O56} nanocage. The reactivity of embedded {HPO3} was fully studied, showing the cluster undergoes a structural rearrangement in solution whereby the {HPO3} moieties dimerise to form a weakly interacting (O3PH···HPO3) moiety. In the crystalline state a temperature-dependent intramolecular redox reaction and structural rearrangement occurs. This rearrangement appears to proceed via an intermediate containing two different templates, a pyramidal {HPO3} and a tetrahedral {PO4} moiety. {HPO3} templated POM cages were then vigorously expanded and led to the isolation of five either fully oxidised or mixed-valence clusters trapped with mono-, di-, or tri- {HPO3}. Interestingly, an intriguing 3D honeycomb-like host-guest structure was also synthesised. The porous framework was self-aggregated by a tri-phopshite anion templated {W21} cluster with a {VO4} templated Wells-Dawson type {W18} acting as a guest species within the hexagonal channels. Based on this work, we further extended the templating anions to two different redox-active heteroanions, and discovered a unique mixed-heteroatom templated system built by pairing redox-active {HPIIIO3} with {TeO3}, {SeO3} or {AsO3}. Two molecular systems were developed, ie. “Trojan Horse” type [W18O56(HPO3)0.8(SeO3)1.2(H2O)2]8- and cross-shaped [H4P4X4W64O224]32-/36-, where X=TeIV, SeIV, AsIII. In the case of {W18(HPO3)0.8(SeO3)1.2}, the compound is found to be a mixture of heteroleptic {W18(HPO3)(SeO3)} and homoleptic {W18(SeO3)2} and {W18(HPO3)2}, identified by single crystal x-ray diffraction, NMR as well as high resolution mass spectrometry. The cluster exhibited similar temperature-dependent electronic features to “Trojan Horse” type {W18(HPO3)2O56}. However, due to the intrinsic reactivity difference between {HPO3} and {SeO3}, the thermal treatment leads to the formation of an unusual species [W18O55(PO4)(SeO3)]5-, in which {HPO3} was fully oxidised to {PO4} within the cage, whereas and lone-pair-containing {SeO3} heteroanions were kept intact inside the shell. This finding is extremely interesting, as it demonstrated that multiple and independent intramolecular electronic performance can be achieved by the coexistence of distinct heteroatoms within a single molecule. On the other hand, the cross-shaped [H4P4X4W64O224]32-/36- were constructed by four {W15(HPO3)(XO3)} building units linked by four {WO6} octahedra. Each building unit traps two different heteroatoms. It is interesting to note that the mixed heteroatom species show self-sorting, with a highly selective positional preference. Smaller ionic sized {HPO3} are self-organised into the uncapped side of {W15} cavity, whereas closed side are occupied by larger heteroatoms, which is surprisingly opposed to steric hindrance. Density functional theory (DFT) calculations are currently underway to have a full understanding of the preference of heteroatom substitutions. This series of clusters is of great interest in terms of achieving single molecule-based heteroatom-dependent multiple levels of electron transfer. It has opened a new way to design and synthesise POMs with higher diversity of electrical states, which may lead to a new type of Q-bits for quantum computing. The third chapter is focused on developing polyoxotungstate building blocks templated by {HPO3}. A series of building blocks, {W15O48(HPO3)2}, {W9O30(HPO3)} {W12O40(HPO3)2} and hexagonal {W6O18(HPO3)} have been obtained. The first four building blocks have been reported with {SeO3} and/or {TeO3} heteroanions. This result demonstrates {HPO3} has a similar reactivity as {SeO3} and {TeO3}, therefore studying the self-assembly of {HPO3}-based building blocks would be helpful to have a general understanding of pyramidal heteroatom-based molecular systems. The hexagonal {W6O18(HPO3)} is observed for the first time in polyoxotungstates, showing some of reactivity difference between {HPO3} and {SeO3} and {TeO3}. Furthermore, inorganic salts and pH values have some directing influence on the formation and transformation of various building blocks, resulting in the discovery of a family of {HPO3}-based clusters with nuclearity ranging from {W29} to {W106}. High resolution mass spectrometry was also carried out to investigate the cluster solution behaviour and also gain information of building block speciation. It is found that some clusters experienced decomposition, which gives rise to potential building blocks accountable for the self-assembly.

High performance terahertz resonant tunnelling diode sources and broadband antenna for air-side radiation

Resonant tunnelling diode (RTD) is known to be the fastest electronics device that can be fabricated in compact form and operate at room temperature with potential oscillation frequency up to 2.5 THz. The RTD device consists of a narrow band gap quantum well layer sandwiched between two thin wide band gap barriers layers. It exhibits negative differential resistance (NDR) region in its current-voltage (I-V) characteristics which is utilised in making oscillators. Up to date, the main challenge is producing high output power at high frequencies in particular. Although oscillation frequencies of ~ 2 THz have been already reported, the output power is in the range of micro-Watts. This thesis describes the systematic work on the design, fabrication, and characterisation of RTD-based oscillators in microwave/millimetre-wave monolithic integrated circuits (MMIC) form that can produce high output power and high oscillation frequency at the same time. Different MMIC RTD oscillator topologies were designed, fabricated, and characterised in this project which include: single RTD oscillator which employs one RTD device, double RTDs oscillator which employs two RTD devices connected in parallel, and coupled RTD oscillators which combine the powers of two oscillators over a single load, based on mutual coupling and which can employ up to four RTD devices. All oscillators employed relatively large size RTD devices for high power operation. The main challenge was to realise high oscillation frequency (~ 300 GHz) in MMIC form with the employed large sized RTD devices. To achieve this aim, proper designs of passive structures that can provide small values of resonating inductances were essential. These resonating inductance structures included shorted coplanar wave guide (CPW) and shorted microstrip transmission lines of low characteristics impedances Zo. Shorted transmission line of lower Zo has lower inductance per unit length. Thus, the geometrical dimensions would be relatively large and facilitate fabrication by low cost photolithography. A series of oscillators with oscillation frequencies in the J-band (220 – 325 GHz) range and output powers from 0.2 – 1.1 mW have been achieved in this project, and all were fabricated using photolithography. Theoretical estimation showed that higher oscillation frequencies (> 1 THz) can be achieved with the proposed MMIC RTD oscillators design in this project using photolithography with expected high power operation. Besides MMIC RTD oscillators, reported planar antennas for RTD-based oscillators were critically reviewed and the main challenges in designing high performance integrated antennas on large dielectric constant substrates are discussed in this thesis. A novel antenna was designed, simulated, fabricated, and characterised in this project. It was a bow-tie antenna with a tuning stub that has very wide bandwidth across the J-band. The antenna was diced and mounted on a reflector ground plane to alleviate the effect of the large dielectric constant substrate (InP) and radiates upwards to the air-side direction. The antenna was also investigated for integration with the all types of oscillators realised in this project. One port and two port antennas were designed, simulated, fabricated, and characterised and showed the suitability of integration with the single/double oscillator layout and the coupled oscillator layout, respectively.