Value-adding Australian sardines: Factors affecting rates of deterioration in sardine (Sardinops sagax) quality during post-harvest handling

Deficiencies in sardine post-harvest handling methods were seen as major impediments to development of a value-adding sector supplying Australian bait and human consumption markets. Factors affecting sardine deterioration rates in the immediate post-harvest period were investigated and recommendations made for alternative handling procedures to optimise sardine quality. Net to factory sampling showed that post-mortem autolysis was probably caused by digestive enzyme activity contributing to the observed temporal increase in sardine Quality Index. Belly burst was not an issue. Sardine quality could be maintained by reducing tank loading, and rapid temperature reduction using dedicated, on-board value-adding tanks. Fish should be iced between the jetty and the processing factory, and transport bins chilled using an efficient cooling medium such as flow ice.

Smart sorbers - value adding spent litter fertiliser. A pilot trial

Currently spent litter is not a balanced fertiliser. This project is a first step in improving the ability to reduce environmental contamination and to more fully realise the full fertilizer and soil amendment value of this material.

The Potential for a New Value Adding Industry for Noni Tropical Fruit Producers

Morinda citrifolia (noni) grows widely throughout the Pacific and is native to Australia. It is a source of traditional medicine amongst Coastal Aboriginal Communities in Cape York, the Pacific Islands and South East Asia, and in recent years has experienced significant economic growth worldwide through a variety of health and cosmetic claims. The largest markets for noni are North America, Europe, Japan, Mexico, Asia and Australia with the worldwide market for these products estimated at US$400 million.

Resin defect impacts on the value of graded recovery and evaluation of technologies for internal defect detection in slash pine logs.

The key outcome will be to identify a technology that is practical to use to scan logs identified by the modelling as suspect or marginal for sawing and to confirm their unsuitability for value adding sawing by internal scanning.

Sustainable native forest management. Case studies in managing private native forest in southeast Queensland.

The introduction describes productive forest in Queensland and summaries the principles of native forest management that achieve optimum productivity. Case study 1 deals with thinning an even-aged regrowth forest. It shows how thinning the stand actively manages the future composition and structure to improve productivity in the best stems and increase the commercial value of the next harvest. Case study 2 describes restoring productivity in a high-graded spotted gum - ironbark forest. It shows that defective and non-saleable trees should be removed so they do not repress the future stand; and that regeneration should be thinned, retaining the best trees in adequate growing space. Case study 3 discusses on-farm value adding for hardwood forests. It shows how long-term viability and maximum productivity and returns depend on the best management practices and knowing how to obtain the best returns from a range of forest products. Case study 4 examines integrated harvesting in a eucalypt forest. It shows how integrating the harvest enables the full range of timber products are harvested and sold for their maximum value while reducing the amount of waste.

Plantation hardwood resource specifications required for planning small log sawing infrastructure investment in Queensland.

Improved information on the product quality of the plantation resource is needed to allow businesses to consider investing in the development of value-adding processing facilities. These facilities are likely to require customised design that optimises the utilisation of future small diameter plantation hardwood logs. This log resource will become available as wood supply in Queensland transitions from native forests to 100% from sustainable plantations. This resource will be controlled by plantations established prior to 2000. A survey of the three main growers (former Forest Enterprises Australia Pty Ltd, former Forestry Corporation of New South Wales, Hancock Queensland Plantation Pty Ltd) revealed that C. citriodora subsp.variegata – CCV (28.0%), Eucalyptus dunnii (27.5%), E. pilularis (23.0%), E. grandis (11.3%) and E. cloeziana –GMS (7.1%) were the most widely planted species in the southern Queensland and northern New South Wales subtropical hardwood estate and would potentially dominate the supply of plantation hardwoods to sawmill processing facilities.

Effects of Low Dose Irradiation on the K-Value and Hypoxanthine Concentration of Fish Fillets

Fillets of five fish species were irradiated at 0, 1 and 3kGy to investigate whether the K-value test of freshness can be applied to irradiated fish. Following irradiation, the fillets were stored on ice and sampled regularly for K-value analysis. Hypoxanthine (Hx) and total nucleotide content were also determined on fillets of two species. K-values of irradiated fillets were generally lower than those of unirradiated controls. Hypoxanthine levels paralleled the K-value changes. These results indicated that quality standards based on K-values or Hx levels that have been set for unirradiated species cannot be directly applied to fish that has been irradiated. Total nucleotide content did not appear to be affected by irradiation.

Getting value out of your sensory testing - the difference from control test

Non-parametric difference tests such as triangle and duo-trio tests traditionally are used to establish differences or similarities between products. However they only supply the researcher with partial answers and often further testing is required to establish the nature, size and direction of differences. This paper looks at the advantages of the difference from control (DFC) test (also known as degree of difference test) and discusses appropriate applications of the test. The scope and principle of the test, panel composition and analysis of results are presented with the aid of suitable examples. Two of the major uses of the DFC test are in quality control and shelf-life testing. The role DFC takes in these areas and the use of other tests to complement the testing is discussed. Controls or standards are important in both these areas and the use of standard products, mental and written standards and blind controls are highlighted. The DFC test has applications in products where the duo-trio and triangle tests cannot be used because of the normal heterogeneity of the product. While the DFC test is a simple difference test it can be structured to give the researcher more valuable data and scope to make informed decisions about their product.

Predicting wood value in Queensland Caribbean pine plantations using a decision support system

A decision support system has been developed in Queensland to evaluate how changes in silvicultural regimes affect wood quality, and specifically the graded recovery of structural timber. Models of tree growth, branch architecture and wood properties were developed from data collected in routine Caribbean pine plantations and specific silvicultural experiments. These models were incorporated in software that simulates the conversion of standing trees into logs, and the logs into boards, and generates detailed data on knot location and basic density distribution. The structural grade of each board was determined by simulating the machine stress-grading process, and the predicted graded recovery provided an indicator of wood value. The decision support system improves the basis of decision-making by simulating the performance of elite genetic material under specified silvicultural regimes and by predicting links between wood quality and general stand attributes such as stocking and length of rotation.

Use of part records in Merino breeding programs - The inheritance of wool growth and fibre traits during different times of the year to determine their value in Merino breeding programs

Fibre diameter can vary dramatically along a wool staple, especially in the Mediterranean environment of southern Australia with its dry summers and abundance of green feed in spring. Other research results have shown a very low phenotypic correlation between fibre diameter grown between seasons. Many breeders use short staples to measure fibre diameter for breeding purposes and also to promote animals for sale. The effectiveness of this practice is determined by the relative response to selection by measuring fibre traits on a full 12 months wool staple as compared to measuring them only on part of a staple. If a high genetic correlation exists between the part record and the full record, then using part records may be acceptable to identify genetically superior animals. No information is available on the effectiveness of part records. This paper investigated whether wool growth and fibre diameter traits of Merino wool grown at different times of the year in a Mediterranean environment, are genetically the same trait, respectively. The work was carried out on about 7 dyebanded wool sections/animal.year, on ewes from weaning to hogget age, in the Katanning Merino resource flocks over 6 years. Relative clean wool growth of the different sections had very low heritability estimates of less than 0.10, and they were phenotypically and genetically poorly correlated with 6 or 12 months wool growth. This indicates that part record measurement of clean wool growth of these sections will be ineffective as indirect selection criteria to improve wool growth genetically. Staple length growth as measured by the length between dyebands, would be more effective with heritability estimates of between 0.20 and 0.30. However, these measurements were shown to have a low genetic correlation with wool grown for 12 months which implies that these staple length measurements would only be half as efficient as the wool weight for 6 or 12 months to improve total clean wool weight. Heritability estimates of fibre diameter, coefficient of variation of fibre diameter and fibre curvature were relatively high and were genetically and phenotypically highly correlated across sections. High positive phenotypic and genetic correlations were also found between fibre diameter, coefficient of variation of fibre diameter and fibre curvature of the different sections and similar measurements for wool grown over 6 or 12 months. Coefficient of variation of fibre diameter of the sections also had a moderate negative phenotypic and genetic correlation with staple strength of wool staples grown over 6 months indicating that coefficient of variation of fibre diameter of any section would be as good an indirect selection criterion to improve stable strength as coefficient of variation of fibre diameter for wool grown over 6 or 12 months. The results indicate that fibre diameter, coefficient of variation of fibre diameter and fibre curvature of wool grown over short periods of time have virtually the same heritability as that of wool grown over 12 months, and that the genetic correlation between fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part and on full records is very high (rg > 0.85). This indicates that fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part records can be used as selection criteria to improve these traits. However, part records of greasy and clean wool growth would be much less efficient than fleece weight for wool grown over 6 or 12 months because of the low heritability of part records and the low genetic correlation between these traits on part records and on wool grown for 12 months.

The value of having no wild rabbits in south-east Queensland

Rabbits released in Australia in 1859 spread to most areas of suitable habitat by 1910 causing great damage to the environment and primary industries. Measurement of damage is essential to justify spending money and utilising resources to remove rabbits. Damage to pasture and biodiversity may be irreversible and therefore difficult to measure without comparison with an area that has never suffered such damage. A rabbit proof fence completed in 1906 protected a large part of south east Queensland from rabbits. The Darling Downs Moreton Rabbit Board (DDMRB) continues to maintain the fence and keep the area relatively free of rabbits. This area is unique because it is highly suitable for rabbits and yet it has never ‘experienced’ the damage caused by plagues of uncontrolled rabbits. A study site was established where the DDMRB fence separates an area heavily used by rabbits (‘dirty side’) from an area that has never been infested by rabbits (‘clean side’). The number and location of all rabbit warrens and log piles were recorded. The absence of warrens from the ‘clean side’ shows clearly that the rabbit proof fence has prevented rabbits from establishing warren systems. The ‘dirty side’ is characterised by a high number of warrens, a high density of rabbits, fewer pasture species and low macropod activity. Future work will determine whether the rabbit populations are viable in the absence of rabbit warrens. We plan to radio collar rabbits on both sides of the fence to measure their survival rate. In selected warrens and log piles of varying degrees of complexity and size, rabbits will be trapped and information on reproduction and age structure will be collected. This will allow better targeting of the source of rabbits during control operations. Once the initial comparative analysis of the site has been completed, all rabbit warrens will be destroyed on the dirty side of the fence. After rabbits are removed from this area, monitoring will continue to determine if pasture and biodiversity on opposite sides of the fence begin to mirror each other.

Resilience of a high-conservation-value, semi-arid grassland on fertile clay soils to burning, mowing and ploughing.

In grassland reserves, managed disturbance is often necessary to maintain plant species diversity. We carried out experiments to determine the impact of fire, kangaroo grazing, mowing and disc ploughing on grassland species richness and composition in a nature reserve in semi-arid eastern Australia. Vegetation response was influenced by winter-spring drought after establishment of the experiments, but moderate rainfall followed in late summer-autumn. Species composition varied greatly between sampling times, and the variability due to rainfall differences between seasons and years was greater than the effects of fire, kangaroo grazing, mowing or disc ploughing. In the fire experiment, species richness and composition recovered more rapidly after spring than autumn burning. Species richness and composition were similar to control sites within 12 months of burning and mowing, suggesting that removal of the dominant grass canopy is unnecessary to enhance plant diversity. Two fires (separated by 3 years) and post-fire kangaroo grazing had only minor influence on species richness and composition. Even disc ploughing caused only a small reduction in native richness. The minor impact of ploughing was explained by the small areas that were ploughed, the once-off nature of the treatment, and the high degree of natural movement and cracking in these shrink-swell soils. Recovery of the composition and richness of these grasslands was rapid because of the high proportion of perennial species that resprout vegetatively after fire and mowing. There appears to be little conservation benefit from fire, mowing or ploughing ungrazed areas, as we could identify no native plant species dependent on frequent disturbance for persistence in this grassland community. However, the ability of the Astrebla- and Dichanthium-dominated grasslands to recover quickly after disturbance, given favourable seasonal conditions, suggests that they are well adapted to natural disturbances (e.g. droughts, fire, flooding and native grazing).

MOE and MOR assessment technologies for improving graded recovery of exotic pines in Australia.

This project was designed to provide the structural softwood processing industry with the basis for improved green and dry grading to allow maximise MGP grade yields, consistent product performance and reduced processing costs. To achieve this, advanced statistical techniques were used in conjunction with state-of-the-art property measurement systems. Specifically, the project aimed to make two significant steps forward for the Australian structural softwood industry: • assessment of technologies, both existing and novel, that may lead to selection of a consistent, reliable and accurate device for the log yard and green mill. The purpose is to more accurately identify and reject material that will not make a minimum grade of MGP10 downstream; • improved correlation of grading MOE and MOR parameters in the dry mill using new analytical methods and a combination of devices. The three populations tested were stiffness-limited radiata pine, strength-limited radiata pine and Caribbean pine. Resonance tests were conducted on logs prior to sawmilling, and on boards. Raw data from existing in-line systems were captured for the green and dry boards. The dataset was analysed using classical and advanced statistical tools to provide correlations between data sets and to develop efficient strength and stiffness prediction equations. Stiffness and strength prediction algorithms were developed from raw and combined parameters. Parameters were analysed for comparison of prediction capabilities using in-line parameters, off-line parameters and a combination of in-line and off-line parameters. The results show that acoustic resonance techniques have potential for log assessment, to sort for low stiffness and/or low strength, depending on the resource. From the log measurements, a strong correlation was found between the average static MOE of the dried boards within a log and the predicted value. These results have application in segregating logs into structural and non-structural uses. Some commercial technologies are already available for this application such as Hitman LG640. For green boards it was found that in-line and laboratory acoustic devices can provide a good prediction of dry static MOE and moderate prediction for MOR.There is high potential for segregating boards at this stage of processing. Grading after the log breakdown can improve significantly the effectiveness of the mill. Subsequently, reductions in non-structural volumes can be achieved. Depending on the resource it can be expected that a 5 to 8 % reduction in non structural boards won’t be dried with an associated saving of $70 to 85/m3. For dry boards, vibration and a standard Metriguard CLT/HCLT provided a similar level of prediction on stiffness limited resource. However, Metriguard provides a better strength prediction in strength limited resources (due to this equipment’s ability to measure local characteristics). The combination of grading equipment specifically for stiffness related predictors (Metriguard or vibration) with defect detection systems (optical or X-ray scanner) provides a higher level of prediction, especially for MOR. Several commercial technologies are already available for acoustic grading on board such those from Microtec, Luxscan, Falcon engineering or Dynalyse AB for example. Differing combinations of equipment, and their strategic location within the processing chain, can dramatically improve the efficiency of the mill, the level of which will vary depending of the resource. For example, an initial acoustic sorting on green boards combined with an optical scanner associated with an acoustic system for grading dry board can result in a large reduction of the proportion of low value low non-structural produced. The application of classical MLR on several predictors proved to be effective, in particular for MOR predictions. However, the usage of a modern statistics approach(chemometrics tools) such as PLS proved to be more efficient for improving the level of prediction. Compared to existing technologies, the results of the project indicate a good improvement potential for grading in the green mill, ahead of kiln drying and subsequent cost-adding processes. The next stage is the development and refinement of systems for this purpose.

Membrane fractionation technologies for high quality mill sugar and value-added by products - an integrated sugar production process concept model.

Membrane filtration technology has been proven to be a technically sound process to improve the quality of clarified cane juice and subsequently to increase the productivity of crystallisation and the quality of sugar production. However, commercial applications have been hindered because the benefits to crystallisation and sugar quality have not outweighed the increased processing costs associated with membrane applications. An 'Integrated Sugar Production Process (ISPP) Concept Model' is proposed to recover more value from the non-sucrose streams generated by membrane processing. Pilot scale membrane fractionation trials confirmed the technical feasibility of separating high-molecular weight, antioxidant and reducing sugar fractions from cane juice in forms suitable for value recovery. It was also found that up to 40% of potassium salts from the juice can be removed by membrane application while removing the similar amount of water with potential energy saving in subsequent evaporation. Application of ISPP would allow sugar industry to co-produce multiple products and high quality mill sugar while eliminating energy intensive refining processes.

Develop added value uses of high anti-bacterial honey

Honey is valued for its medicinal properties. There interest from industry to develop a rapid method to detect the bioactivity of honey and also to develop value added products from high antibacterial honey.